http://www.openzwave.com/device-database/031E:0001:0001 images/inovelli/lzw31-sn.png https://products.z-wavealliance.org/products/3438 https://inovelli.com/shop/smart-light-switches/zwave-smart-switches-gen2/pre-order-z-wave-dimmer-switch-no-neutral-required-scenes-notification/ https://inovelli.com/shop/smart-light-switches/zwave-smart-switches-gen2/pre-order-z-wave-dimmer-switch-no-neutral-required-scenes-notification/ To Exclude your switch, put your HUB in exclusion mode and press the Configuration Button three (3) times. U.S. / Canada / Mexico https://products.z-wavealliance.org/ProductManual/File?folder=&filename=MarketCertificationFiles/3438/LZW31-SN%20Manual.pdf You may factory reset the switch by holding down the Config Button for twenty (20) or more seconds. The LED Bar will turn Red and blink three (3) times to confirm. However, we recommend using a certified Z-Wave controller to remove the device from your network for factory resetting the switch. Only use either of these procedures in the event that the network primary controller is missing or otherwise inoperable. The Inovelli Red Series Dimmer is a Z-Wave in-wall dimmer that controls attached LED, CFL, & Incandescent lighting which can be highly customized to your liking at the switch itself with our unique config button and advanced firmware. The switch can also be used either with or without a neutral wire. In addition, the Red Series comes with advanced features such as scene support, power monitoring, notifications, local protection, etc. LZW31-SN Dimmer LZW31-SN To include your switch, start the inclusion process on your HUB and tap the Configuration Button three (3) times. Please Note: If this doesn't work, you can check to see if your switch is within Z-Wave Range by holding down the Configuration Button for 5-10 seconds (if it's not within range, the LED Bar will indicate Red and if it is within Range, the LED Bar will indicate Green). If your switch indicates Red, please move the switch closer to the HUB. If your switch indicates Green, please try running an Exclusion to reset your switch. Initial Release Update config for Firmware 1.47+ Clarifying which scenes are disabled with parameter 51 Fix maximum value for parameter 16 Fixing value range for parameter 9 and 10 This changes the speed in which the attached light dims up or down. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. Range:0-100 Default: 3 This changes the speed in which the attached light dims up or down when controlled from the physical switch. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 101 should keep this in sync with parameter 1. Range:0-101 Default: 101 This changes the speed in which the attached light turns on or off. For example, when a user sends the switch a basicSet(value: 0xFF) or basicSet(value: 0x00), this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 101 should keep this in sync with parameter 1. Range:0-101 Default: 101 This changes the speed in which the attached light turns on or off from the physical switch. For example, when a user presses the up or down button, this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 101 should keep this in sync with parameter 1. Range:0-101 Default: 101 The minimum level that the dimmer allows the bulb to be dimmed to. Useful when the user has an LED bulb that does not turn on or flickers at a lower level. Range:1-45 Default: 1 The maximum level that the dimmer allows the bulb to be dimmed to. Useful when the user has an LED bulb that reaches its maximum level before the dimmer value of 99. Range:55-99 Default: 99 Inverts the orientation of the switch. Useful when the switch is installed upside down. Essentially up becomes down and down becomes up. Range: 0-1 Default: 0 Automatically turns the switch off after this many seconds. When the switch is turned on a timer is started that is the duration of this setting. When the timer expires, the switch is turned off. Range:0-32767 Default: 0 Default level for the dimmer when it is powered on from the local switch. A setting of 0 means that the switch will return to the level that it was on before it was turned off. Range:0-99 Default: 0 Default level for the dimmer when it is powered on from a Z-Wave command. A setting of 0 means that the switch will return to the level that it was on before it was turned off. Range:0-99 Default: 0 The state the switch should return to once power is restored after power failure. 0 = off, 1-99 = level, 100=previous. Range:0-100 Default: 0 When should the switch send commands to associated devices? 01 - local 02 - 3way 03 - 3way & local 04 - z-wave hub 05 - z-wave hub & local 06 - z-wave hub & 3-way 07 - z-wave hub & local & 3way 08 - timer 09 - timer & local 10 - timer & 3-way 11 - timer & 3-way & local 12 - timer & z-wave hub 13 - timer & z-wave hub & local 14 - timer & z-wave hub & 3-way 15 - all Range: 0-15 Default: 15 This is the color of the LED strip. Range: 0 to 255 Default: 170 This is the intensity of the LED strip. Range: 0-10 Default: 5 This is the intensity of the LED strip when the switch is off. This is useful for users to see the light switch location when the lights are off. Range: 0-10 Default: 1 Please see website for documentation. Range: 0-100600575 Default: 0 When the LED strip is disabled (LED Strip Intensity is set to 0), this setting allows the LED strip to turn on temporarily while being adjusted. Range: 0-10 Default: 3 The power level change that will result in a new power report being sent. The value is a percentage of the previous report. 0 = disabled. Range:0-100 Default: 10 Time period between consecutive power & energy reports being sent (in seconds). The timer is reset after each report is sent. Range:0-32767 Default: 3600 The energy level change that will result in a new energy report being sent. The value is a percentage of the previous report. Range:0-100 Default: 10 Configure the switch to use a neutral wire. Range: 0-1 Default: 1 Configure the type of 3-way switch connected to the dimmer. Range: 0-2 Default: 0 Enables instant on (ie: disables the 700ms button delay). Note, if you disable the delay, it will also disable scene control except for the following: Up pres sed, held, released, Down pressed, held, released & config button pressed. Optimize power output to be more compatible with smart bulbs. This prevents the dimmer from being able to dim and makes it act like an ON / OFF switch. (firmware 1.47+)