http://www.openzwave.com/device-database/031E:0001:000a
images/inovelli/lzw31-sn.png
https://products.z-wavealliance.org/products/3438
TBD
TBD
TBD
U.S. / Canada / Mexico
TBD
TBD
TBD
LZW45 LED Light Strip
LZW45
TBD
Initial Release
Fix device type, fix some issues with parameter sizes
Updates to work with firmware 1.16
Updates to work with firmware 1.17
Updates to work with firmware 1.18
Updates parameter 30 to 4 bytes
When individually addressable LEDs are used, this parameter tells the controller the number of pixels that are attached.
0: Automatic recognition of pixels
Range 1 - 130: Set the fixed value of the pixel bit
Default: 0
This changes the speed in which the light strip dims up or down. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed.
Range 0 - 98: Set the dimming speed
Default: 4
This changes the speed in which the light strip turns on or off. For example, when a user sends the switch a basicSet(value: 0xFF) or basicSet(value: 0x00), this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter 2.
Range 0 - 98: Set the Ramp Rate
99: Keep in sync with parameter 2
Default: 99
The minimum level that the strip can be dimmed to. Useful when the user has an LED strip that does not turn on or flickers at a lower level.
Range: 1 - 45
Default: 1
The maximum level that the strip can be dimmed to. Useful when the user has an LED strip that reaches its maximum level before the dimmer value of 99.
Range: 55 - 99
Default: 99
Automatically turns the strip off after this many seconds. When the strip is turned on a timer is started that is the duration of this setting. When the timer expires, the strip is turned off.
0 - Auto off is disabled
Range: 0 - 32767
Default level for the strip when it is powered on from the local switch. A setting of 0 means that the switch will return to the level that it was on before it was turned off.
Range 0 - 99
Default: 0
Default level for the dimmer when it is powered on from a Z-Wave command (i.e. BasicSet(0xFF)). A setting of 0 means that the switch will return to the level that it was on before it was turned off.
Range: 0-99
Default: 0
Byte(3-2): Values between 2700-6500 represent a color temperature.
Byte(1-0): Values between 0-361, represent the color on the Hue color wheel. The value of 361 represents a random color.
Range: 0 - 425984362
Default: 262144000
The state the switch should return to once power is restored after power failure.
0 - Off
1 - Default Color / Level (Parameter 9)
2 - Previous
Default: Previous
The power level change that will result in a new power report being sent. The value is a percentage of the previous report. 0 = disabled.
Range: 0 - 100
Default: 10
Time period between consecutive power & energy reports being sent (in seconds). The timer is reset after each report is sent.
Range: 0, 30 - 32767
Default: 3600
The energy level change that will result in a new energy report being sent (in kWh)
0 = 0.01kWh, 10=0.1kWh, 100=1kWh
Range:0-127
Default: 10
See website for details
* Sending Basic, Binary Switch, Multilevel, and Color SET will automatically disable the strip effect.
* Toggling OFF -> ON will cancel effect mode set on LED Strip and change the LED Strip back to the Previous color.
Range: 0 - 2147483647
Default: 0
See website for details.
Range: 0 - 2147483647
Default: 0
See website for details.
Range: 0 - 2147483647
Default: 0
See website for details.
Range: 0 - 2147483647
Default: 0
See website for details.
Range: 0 - 65535
Default: 0
Byte 1 - Level
Byte 0 - Effect
See website for details.
Default: 0
The 700ms delay that occurs after pressing the physical button to turn the switch on/off is removed. Consequently this also removes the following scenes: 2x, 3x, 4x, 5x tap. Still working are the 1x tap, held, released, and the level up/down scenes. (firmware 1.36+)
0 - 700ms delay disabled (some scenes will not work)
1 - 700ms delay enabled (All scenes work)
Default: 700ms delay enabled