# This file allows user to override the factory # defaults for the WLAN Driver # Enable IMPS or not gEnableImps=1 # Enable/Disable Idle Scan gEnableIdleScan=0 # Increase sleep duration (seconds) during IMPS # 0 implies no periodic wake up from IMPS. Periodic wakeup is # unnecessary if Idle Scan is disabled. gImpsModSleepTime=0 # Enable BMPS or not gEnableBmps=1 # Enable suspend or not # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter gEnableSuspend=3 # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac gDot11Mode=0 # CSR Roaming Enable(1) Disable(0) gRoamingTime=0 # Assigned MAC Addresses - This will be used until NV items are in place # Each byte of MAC address is represented in Hex format as XX Intf0MacAddress=000AF58989FF Intf1MacAddress=000AF58989FE Intf2MacAddress=000AF58989FD Intf3MacAddress=000AF58989FC # Set/Clear UAPSD mask UapsdMask=0 # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=20 InfraUapsdViSrvIntv=40 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 # Make 1x1 the default antenna configuration gNumRxAnt=1 # Beacon filtering frequency (unit in beacon intervals) gNthBeaconFilter=50 # Enable WAPI or not # WAPIIsEnabled=0 # Flags to filter Mcast abd Bcast RX packets. # Value 0: No filtering, 1: Filter all Multicast. # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast McastBcastFilter=3 #Flag to enable HostARPOffload feature or not hostArpOffload=1 #SoftAP Related Parameters # AP MAc addr gAPMacAddr=000AF589dcab # 802.11n Protection flag gEnableApProt=1 #Enable OBSS protection gEnableApOBSSProt=1 #Enable/Disable UAPSD for SoftAP gEnableApUapsd=1 # Fixed Rate gFixedRate=0 # Maximum Tx power # gTxPowerCap=30 # Fragmentation Threshold # gFragmentationThreshold=2346 # RTS threshold RTSThreshold=2347 # Intra-BSS forward gDisableIntraBssFwd=0 # WMM Enable/Disable WmmIsEnabled=0 # 802.11d support g11dSupportEnabled=0 # CCX Support and fast transition EseEnabled=0 FastTransitionEnabled=1 ImplicitQosIsEnabled=0 gNeighborScanTimerPeriod=200 # default value of this parameter is zero to enable dynamic threshold allocation # to set static roming threshold uncomment below parameter and set vaule #gNeighborLookupThreshold=78 gNeighborScanChannelMinTime=20 gNeighborScanChannelMaxTime=30 # Legacy (non-CCX, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 #Check if the AP to which we are roaming is better than current AP in terms of RSSI. #Checking is disabled if set to Zero.Otherwise it will use this value as to how better #the RSSI of the new/roamable AP should be for roaming RoamRssiDiff=5 # SAP Country code # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. # Example # US Indoor, USI # Korea Outdoor, KRO # Japan without optional byte, JP # France without optional byte, FR #gAPCntryCode=USI #Short Guard Interval Enable/disable gShortGI20Mhz=1 gShortGI40Mhz=1 #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled gAPAutoShutOff=0 # SAP auto channel selection configuration # 0 = disable auto channel selection # 1 = enable auto channel selection, channel provided by supplicant will be ignored gApAutoChannelSelection=0 # Listen Energy Detect Mode Configuration # Valid values 0-128 # 128 means disable Energy Detect feature # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. # 10-128 are reserved. # The EDET threshold mapping is as follows in 3dB step: # 0 = -60 dBm # 1 = -63 dBm # 2 = -66 dBm # ... # 7 = -81 dBm # 8 = -84 dBm # 9 = -87 dBm # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: # # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. # gEnablePhyAgcListenMode=128 #Preferred channel to start BT AMP AP mode (0 means, any channel) BtAmpPreferredChannel=0 #Preferred band (both or 2.4 only or 5 only) BandCapability=0 #Beacon Early Termination (1 = enable the BET feature, 0 = disable) enableBeaconEarlyTermination=1 beaconEarlyTerminationWakeInterval=11 #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) gEnableBtAmp=0 #SOFTAP Channel Range selection gAPChannelSelectStartChannel=1 gAPChannelSelectEndChannel=11 #SOFTAP Channel Range selection Operating band # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND 5: 5GHZ BAND gAPChannelSelectOperatingBand=0 #Channel Bonding gChannelBondingMode5GHz=1 gEnableModulatedDTIM = 3 gMaxLIModulatedDTIM = 3 gEnableDatainactivity = 200 #Enable Keep alive with non-zero period value gStaKeepAlivePeriod=30 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). #For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) #For both active and power save clients. #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. #If doesn't honor for 5 seconds then Driver remove client. #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod).. #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period #where we send NULL frame. #gApLinkMonitorPeriod = 10 #gGoLinkMonitorPeriod = 10 #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. gGoKeepAlivePeriod = 10 gApKeepAlivePeriod = 30 #If set will start with active scan after driver load, otherwise will start with #passive scan to find out the domain #gEnableBypass11d=1 #If set to 0, will not scan DFS channels gEnableDFSChnlScan=1 gEnableLogp=1 # Enable Automatic Tx Power control gEnableAutomaticTxPowerControl=0 # 0 for OLPC 1 for CLPC and SCPC gEnableCloseLoop=1 #Data Inactivity Timeout when in powersave (in ms) gDataInactivityTimeout=200 gEnableLpwrImgTransition=1 # Scan Timing Parameters # gPassiveMaxChannelTime=110 # gPassiveMinChannelTime=60 # Enable Tx LDPC #gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT gTxLdpcEnable=3 # gActiveMaxChannelTime=40 # gActiveMinChannelTime=20 # Valid values are 2048,4096,8192 and so on # Please don't use values other than the ones mentioned above gMaxMediumTime=4096 # 802.11K support gRrmEnable=1 gRrmOperChanMax=8 gRrmNonOperChanMax=8 gRrmRandIntvl=100 #Scan offload gEnableDirectedScanOffload=0 #FlexConnect Power Factor #Default is set to 0 (disable) gFlexConnectPowerFactor=0 gVhtChannelWidth=2 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # Enable Tx beamforming gTxBFEnable=1 #Enable/Disable TDLS Feature gEnableTDLSSupport=1 #Enable/Disable TDLS Implicit Trigger gEnableTDLSImplicitTrigger=0 #Enable/Disable TDLS WMM Mode gEnableTDLSWmmMode=1 #Enable/Disable TDLS Buffer Sta gEnableTDLSBufferSta=1 #Enable mac spoofing for firmware scans only (disabled in host scans) gEnableMacAddrSpoof=2 #Disable Fatal event gEnableFatalEvent=0 END # Note: Configuration parser would not read anything past the END marker