[include mainsail.cfg] [include timelapse.cfg] [include get_ip.cfg] [include Macro.cfg] [include moonraker_obico_macros.cfg] [mcu] serial: /dev/ttyACM1 restart_method: command [mcu extra_mcu] serial: /dev/ttyACM0 restart_method: command [adxl345] cs_pin:extra_mcu:PB12 [exclude_object] [resonance_tester] accel_chip: adxl345 probe_points: 175, 175, 30 # an example175 Y175 Z30 accel_per_hz:50 min_freq:1 max_freq:100 max_smoothing:0.2 hz_per_sec:0.5 [temperature_sensor mcu_temp] sensor_type: temperature_mcu min_temp:0 max_temp:100 [temperature_sensor Host_temp] sensor_type: temperature_host min_temp: 0 max_temp: 110 [temperature_sensor Toolhead_Temp] sensor_type: temperature_mcu sensor_mcu: extra_mcu [virtual_sdcard] path:/home/sovol/printer_data/gcodes/ [pause_resume] [printer] kinematics: corexy max_velocity: 700 max_accel: 40000 max_accel_to_decel: 10000 max_z_velocity: 20 max_z_accel: 500 square_corner_velocity: 5.0 [input_shaper] damping_ratio_x: 0.001 damping_ratio_y: 0.001 shaper_type_x = mzv shaper_freq_x = 35 shaper_type_y = mzv shaper_freq_y = 35 [probe] pin: extra_mcu:PB6 x_offset: -17 y_offset: 10 #z_offset : 0 speed: 15.0 speed: 5.0 samples: 2 sample_retract_dist: 2.0 lift_speed: 50 samples_result: average samples_tolerance: 0.016 samples_tolerance_retries: 2 [probe_pressure] pin: ^!PE12 x_offset: 0 y_offset: 0 z_offset : 0 speed: 1.0 [homing_override] gcode: {% if not 'Z' in params and not 'Y' in params and 'X' in params %} G28 X G0 X348 F1200 {% elif not 'Z' in params and not 'X' in params and 'Y' in params %} G28 Y G0 Y360 F1200 {% elif not 'Z' in params and 'X' in params and 'Y' in params %} G28 Y G0 Y360 F1200 G4 P2000 G28 X G0 X348 F1200 {% elif 'Z' in params and not 'X' in params and not 'Y' in params %} G90 G0 X191 Y165 F3600 G28 Z G0 Z10 F600 {% else %} G90 G0 Z5 F300 G28 Y G0 Y360 F1200 G4 P2000 G28 X G0 X348 F1200 G90 G0 X191 Y165 F3600 G28 Z G0 Z10 F600 {% endif %} axes: xyz set_position_z: 0 [bed_mesh] speed: 500 horizontal_move_z: 5 mesh_min: 10,10 mesh_max: 333,340 probe_count: 9,9 algorithm: bicubic bicubic_tension: 0.4 split_delta_z: 0.016 mesh_pps:3,3 adaptive_margin: 5 fade_start: 0 fade_end: 10 fade_target: 0 [quad_gantry_level] gantry_corners: -60,-10 410,420 points: 36,10 36,320 346,320 346,10 speed: 400 horizontal_move_z: 10 retry_tolerance: 0.05 retries: 5 max_adjust: 30 [z_offset_calibration] center_xy_position:191,165 endstop_xy_position:289,361 z_hop: 10 z_hop_speed: 15 [stepper_x] step_pin: PE2 dir_pin: !PE0 enable_pin: !PE3 rotation_distance: 40 microsteps: 16 full_steps_per_rotation:200 endstop_pin: tmc2209_stepper_x: virtual_endstop position_min: 0 position_endstop: 355 position_max: 355 homing_speed: 30 homing_retract_dist: 0 homing_positive_dir: True #-------------------------------------------------------------------- [tmc2209 stepper_x] uart_pin: PE1 interpolate: True run_current: 1.5 hold_current: 1.5 sense_resistor: 0.150 stealthchop_threshold: 0 uart_address:3 driver_sgthrs: 65 diag_pin: PE15 [stepper_y] step_pin: PB8 dir_pin: !PB6 enable_pin: !PB9 rotation_distance: 40 microsteps: 16 full_steps_per_rotation:200 endstop_pin: tmc2209_stepper_y: virtual_endstop position_min: 0 position_endstop: 364 position_max: 364 homing_speed: 30 homing_retract_dist: 0 homing_positive_dir: true #-------------------------------------------------------------------- [tmc2209 stepper_y] uart_pin: PB7 interpolate: True run_current: 1.5 hold_current: 1.5 sense_resistor: 0.150 stealthchop_threshold: 0 uart_address:3 driver_sgthrs: 65 diag_pin: PE13 [stepper_z] #motherboard：Z3 step_pin:PC0 dir_pin:PE5 enable_pin:!PC1 rotation_distance: 40 gear_ratio: 80:12 microsteps: 16 endstop_pin: probe:z_virtual_endstop position_max: 347 position_min: -5 #position_endstop: 0 homing_speed: 15.0 homing_retract_dist: 5.0 homing_retract_speed: 15.0 second_homing_speed: 10.0 [tmc2209 stepper_z] uart_pin: PE6 interpolate: true run_current: 0.58 hold_current: 0.58 sense_resistor: 0.150 stealthchop_threshold: 999999 uart_address:3 [stepper_z1] ##motherboard：Z1 step_pin:PD3 dir_pin:!PD1 enable_pin:!PD4 rotation_distance: 40 gear_ratio: 80:12 microsteps: 16 [tmc2209 stepper_z1] uart_pin:PD2 interpolate: true run_current: 0.58 hold_current: 0.58 sense_resistor: 0.150 stealthchop_threshold: 999999 uart_address:3 [stepper_z2] ##motherboard：Z2 step_pin:PD7 dir_pin:PD5 enable_pin:!PB5 rotation_distance: 40 gear_ratio: 80:12 microsteps: 16 [tmc2209 stepper_z2] uart_pin:PD6 interpolate: true run_current: 0.58 hold_current: 0.58 sense_resistor: 0.150 stealthchop_threshold: 999999 uart_address:3 [stepper_z3] ##motherboard：Z4 step_pin:PD11 dir_pin:!PD9 enable_pin:!PD12 rotation_distance: 40 gear_ratio: 80:12 microsteps: 16 [tmc2209 stepper_z3] uart_pin:PD10 interpolate: true run_current: 0.58 hold_current: 0.58 sense_resistor: 0.150 uart_address:3 stealthchop_threshold: 999999 [thermistor my_thermistor_e] temperature1:25 resistance1:110000 temperature2:100 resistance2:7008 temperature3:220 resistance3:435 [extruder] step_pin: extra_mcu:PA8 dir_pin: extra_mcu:PB8 enable_pin:!extra_mcu: PB11 rotation_distance: 6.5 microsteps: 16 full_steps_per_rotation: 200 nozzle_diameter: 0.400 filament_diameter: 1.75 max_extrude_only_distance: 150 heater_pin:extra_mcu:PB9 sensor_type:my_thermistor_e pullup_resistor: 11500 sensor_pin: extra_mcu:PA5 min_temp: 5 max_temp: 305 max_power: 1.0 min_extrude_temp: 150 control : pid pid_kp : 33.838 pid_ki : 5.223 pid_kd : 47.752 pressure_advance: 0.025 pressure_advance_smooth_time: 0.035 [tmc2209 extruder] uart_pin: extra_mcu:PB10 interpolate: True run_current: 0.8 hold_current: 0.8 uart_address:3 sense_resistor: 0.150 [verify_heater extruder] max_error: 120 check_gain_time:30 hysteresis: 5 heating_gain: 2 [filament_switch_sensor filament_sensor] pause_on_runout: True event_delay: 3.0 pause_delay: 0.5 switch_pin: PE9 [thermistor my_thermistor] temperature1:25 resistance1:100000 temperature2:50 resistance2:18085.4 temperature3:100 resistance3:5362.6 [heater_bed] heater_pin:PA0 sensor_type: my_thermistor sensor_pin: PC5 max_power: 1.0 min_temp: 5 max_temp: 105 control : pid pid_kp : 73.571 pid_ki : 1.820 pid_kd : 783.849 [verify_heater heater_bed] max_error: 120 check_gain_time:40 hysteresis: 5 heating_gain: 2 [fan_generic fan0] # back model cooling fan pin: extra_mcu:PA7 max_power: 1.0 [fan_generic fan1] # front model cooling fan pin: extra_mcu:PB1 max_power: 1.0 [fan_generic fan3] # exhaust fan pin: PA2 max_power: 1.0 [heater_fan hotend_fan] pin: extra_mcu:PA6 max_power: 1.0 kick_start_time: 0.5 heater: extruder heater_temp: 45 tachometer_pin:extra_mcu:PA1 tachometer_ppr: 1 tachometer_poll_interval: 0.0013 [board_pins] aliases: # EXP1 header EXP1_1=PA8, EXP1_2=PC9, EXP1_3=PA10, EXP1_4=PA9, EXP1_5=PC11, EXP1_6=PC10, EXP1_7=PD8, EXP1_8=PC12, EXP1_9=, EXP1_10=<5V>, # EXP2 header EXP2_1=PB14, EXP2_2=PB13, EXP2_3=PC7, EXP2_4=PB12, EXP2_5=PC6, EXP2_6=PB15, EXP2_7=PC8, EXP2_8=, EXP2_9=, EXP2_10=<5V> [display] lcd_type: uc1701 cs_pin: EXP1_3 a0_pin: EXP1_4 rst_pin: EXP1_5 encoder_pins: ^EXP2_5, ^EXP2_3 click_pin: ^!EXP1_2 contrast: 63 spi_software_miso_pin: EXP2_1 spi_software_mosi_pin: EXP2_6 spi_software_sclk_pin: EXP2_2 [output_pin beeper] pin: EXP1_1 pwm: False value: 0 [neopixel Screen_Colour] pin: EXP1_6 chain_count: 3 color_order: RGB initial_RED: 0.5 initial_GREEN: 0.4 initial_BLUE: 0.7 [gcode_arcs] resolution: 1.0 [output_pin main_led] pin:PA3 pwm: 1 value:1 cycle_time: 5 [idle_timeout] gcode: _IDLE_TIMEOUT timeout: 600 [save_variables] filename =/home/sovol/printer_data/config/saved_variables.cfg #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [probe] #*# z_offset = 1.0