[SCSI] # Settings that apply to all SCSI IDs # Select a system preset to apply default settings # Known systems: "Mac", "MacPlus", "MPC3000", "MegaSTE", "X68000" #System="Mac" #Debug = 0 # Same effect as DIPSW2, enables verbose log messages #SelectionDelay = 255 # Millisecond delay after selection, 255 = automatic, 0 = no delay #Dir = "/" # Optionally look for image files in subdirectory #Dir2 = "/images" # Multiple directories can be specified Dir1...Dir9 #DisableStatusLED 1 # 0: Use status LED, 1: Disable status LED # NOTE: PhyMode is only relevant for ZuluSCSI V1.1 at this time. #PhyMode = 0 # 0: Best available 1: PIO 2: DMA_TIMER 3: GREENPAK_PIO 4: GREENPAK_DMA # The PhyMode parameter has no effect on ZuluSCSI RP2040-based platforms, as there is only one PHY mode. # Settings that can be needed for compatibility with some hosts #Quirks = 0 # 0: Standard, 1: Apple, 2: OMTI, 4: Xebec, 8: VMS, 16: X68000, 32: EWSD #EnableUnitAttention = 0 # Post UNIT_ATTENTION status on power-on or SD card hotplug #EnableSCSI2 = 1 # Enable faster speeds of SCSI2 #EnableSelLatch = 0 # For Philips P2000C and other devices that release SEL signal before BSY #EnableParity = 1 # Enable parity checks on platforms that support it (RP2040) #MapLunsToIDs = 0 # For Philips P2000C simulate multiple LUNs #MaxSyncSpeed = 10 # Set to 5 or 10 to enable synchronous SCSI mode, 0 to disable #InitPreDelay = 0 # How many milliseconds to delay before the SCSI interface is initialized #InitPostDelay = 0 # How many milliseconds to delay after the SCSI interface is initialized # ROM settings #DisableROMDrive = 1 # Disable the ROM drive if it has been loaded to flash #ROMDriveSCSIID = 7 # Override ROM drive's SCSI ID #Initiator settings #InitiatorID = 7 # SCSI ID, 0-7, when the device is in initiator mode, default is 7 #InitiatorMaxRetry = 5 # number of retries on failed reads 0-255, default is 5 #InitiatorImageHandling = 0 # 0: skip exisitng images, 1: create new image with incrementing suffix, 2: overwrite exising image #EnableCDAudio = 0 # Enable CD audio - an external I2S DAC on the v1.2 is required # Settings that can be specified either per-device or for all devices. # Select a device preset to apply default settings # Known systems: "ST32430N" #Device = "ST32430N" #Vendor = "QUANTUM" #Product = "FIREBALL1" #Version = "1.0" #Serial = "0123456789ABCDEF" #Type = 0 # 0: Fixed, 1: Removable, 2: Optical, 3: Floppy, 4: Mag-optical, 5: Tape, 6: Network #VendorExtensions = 0 # Bit flags for specific extensions per device type # CDROM - 1: Plextor's d8h vendor command #TypeModifier = 0 # Affects only INQUIRY response #SectorsPerTrack = 63 #HeadsPerCylinder = 255 #RightAlignStrings = 0 # Right-align SCSI vendor / product strings #PrefetchBytes = 8192 # Maximum number of bytes to prefetch after a read request, 0 to disable #ReinsertCDOnInquiry = 1 # Reinsert any ejected CD-ROM image on Inquiry command #ReinsertAfterEject = 1 # Reinsert next CD image after eject, if multiple images configured. #EjectButton = 0 # Enable eject by button 1 or 2, or set 0 to disable #CDAVolume = 63 # Change CD Audio default volume. Maximum 255. #DisableMacSanityCheck = 0 # Disable sanity warnings for Mac disk drives. Default is 0 - enable checks # SCSI DaynaPORT settings #WiFiSSID = "Wifi SSID string" #WiFiPassword = "WiFi Password" #WiFiMACAddress = "01:23:45:67:89" # Settings can be overridden for individual devices. #[SCSI2] #Product = "Disk with ID2" #[SCSI5] #Product = "CD-ROM Drive" #Type = 2 # If IMG0..IMG9 are specified, they are cycled after each CD eject command. #IMG0 = FirstCD.iso #IMG1 = SecondCD.bin # Raw sector range from SD card can be passed through # Format is RAW:first_sector:last_sector where sector numbers can be decimal or hex. # If end sector is beyond end of SD card, it will be adjusted automatically. # [SCSI4] # IMG0 = RAW:0x00000000:0xFFFFFFFF # Whole SD card