#### ALL FULL DEFINITIONS PARAMETERS #### #### ALL GENERATED DEFINITIONS PARAMETERS #### 1st injection timing MAP for WOT intake split injection 2nd injection timing MAP for WOT intake split injection ABS enabled Advance learning permission upper limit increase coefficient AF learned value maximum AF learned value minimum ECT AF learned value minimum AFM enabled AFM flow AFM maximum voltage AFM minimum voltage After CAT back pressure Air temperature fuel compensation cranking Air temperature ignition compensation (MAP high) Air temperature ignition compensation (MAP low) Air temperature ignition compensation high (MAP>40 kPa) Air temperature ignition compensation low (MAP<40 kPa) Boost by ethanol limit Boost pressure reverse lookup CAEX angle map CAEX upper limit CAIN angle map Calibration ID Cam angle exhaust limit #1 Cam angle exhaust limit #2 Cam angle exhaust limit #3 Cam angle exhaust limit #4 Cam angle exhaust limit #5 Cam angle exhaust WOT #1 Cam angle exhaust WOT #2 Cam angle exhaust WOT Cam angle intake WOT #1 Cam angle intake WOT #2 Cam angle intake WOT Closed loop target lambda high load Closed loop target lambda limit Closed loop target lambda low load Closed loop target lambda Cold start idle air control system (P050A, P050B) Combustion torque conversion Coolant thermostat temperature check enabled (P0128) Cranking fuel pressure Default PA value Digital AFM flow Direct injection time lower limit Direct injector Flow #1 Direct injector Flow #2 Direct injector Flow #3 Direct injector Flow #4 Direct injector Flow #5 Direct injector Flow (Large) #1 Direct injector Flow (Large) #2 Direct injector Flow (Large) #3 Direct injector Flow (Large) #4 Direct injector Flow (Large) #5 Driving force 10 Driving force 2 Driving force 3 Driving force 4 Driving force 5 Driving force 6 Driving force 7 Driving force 8 Driving force 9 Driving force MT EGR area target CAEX angle map upper limit EGR enabled EGR Ignition high EGR Ignition EGT prediction MAP by air intake ELD enabled EPS enabled ETACVTCH1 #1 ETACVTCH1 #2 ETACVTCH1 #3 ETACVTCH1 #4 Ethanol ignition compensation EVAP FTP enabled (P0451 P0452 P0453 P1454) EVAP leak detection enabled (P0455 P0456 P0457) EVAP VSV error check enabled (P0498 P0499) EWG low voltage error threshold hiss high EWG low voltage error threshold hiss lo EWG lower limit voltage EWG out of range upper limit voltage EWG upper limit voltage F / S detection already during KIGKNA assignment value FCAN malfunction (U0073 U0155) enabled(Off=32767,On=4000) final gear ratio (for GSI) final reduction ratio Forced induction enabled Fuel pressure abnormality detection time Fuel pressure abnormality determination lower threshold Fuel pressure abnormality high threshold Fuel pressure abnormality low threshold Fuel pump drive angle #1 Fuel pump drive angle #2 Fuel pump drive angle #3 Fuel pump drive angle #4 Fuel pump drive angle #5 High speed throttle reduction speed Idle speed (after start) Idle speed (normal) Idle Speed Ignition (split) Ignition dwell angle voltage compensation Ignition type(Off=0,On=256) IGRLMTETACH Immobilizer enabled(Off=0,On=6) Individual cylinder fuel trim Individual cylinder ignition trim Initial knock control value Injection timing MAP (water temperature base) #1 Injection timing MAP (water temperature base) #2 Injection timing MAP (water temperature base) #3 Injection timing MAP (water temperature base) #4 Injection timing MAP (water temperature base) #5 Injector phase (WOT) Intake air system leak (P2279) KIGKNA lower limit value of the learning value KIGKNA upper limit value of the learning value Knock air limit #1 Knock air limit #2 Knock air limit high #1 Knock air limit high #2 Knock ignition limit #1 Knock ignition limit #2 Knock ignition limit high #1 Knock ignition limit high #2 Knock retard high Knock sensitivity cylinder 1-4 Knock sensitivity cylinder 2-3 Knock sensitivity high cylinder 1-4 Knock sensitivity high cylinder 2-3 Knock sensor enabled KWOT high KWOT low LAF voltage to lambda Launch recover rpm #1 Launch recover rpm #2 Launch rpm #1 Launch rpm #2 Launch rpm disengage speed Lean best torque high Lean best torque Long term fuel trim error limit high Long term fuel trim error limit low Long term fuel trim maximum Long term fuel trim minimum MAF Load Limit MAP too low / too high enabled (P1127 P1128) Mass or volume circuit range performance problem enabled (P0101) Max discharge rate Max throttle limit request Max throttle limit Maximum MAP voltage Maximum supercharging pressure calculation standard state atmospheric pressure for out Maximum TC sensor voltage Minimum MAP voltage Minimum TC sensor voltage Misfire detection OBD MODE $01 PID $1C value Overrun cutoff MAP (cut) Overrun cutoff MAP (recover) Overrun cutoff MAP high cam (cut) Overrun cutoff MAP high cam (recover) Overrun fuel cut delay Overrun injector restart rpm (cut) Overrun injector restart rpm (recover) P1658 starter enable lrelay control circuit enabled(Off=32767,On=200) PA sensor enabled PA vs MAP error enabled (P2227) Post Start Idle Speed Primary oxygen sensor enabled Purge/EVAP enabled Radiator fan speed 1 off threshold Radiator fan speed 1 on threshold Radiator fan speed 2 off threshold Radiator fan speed 2 on threshold Radiator fan speed 3 off threshold Radiator fan speed 3 on threshold Readiness codes enabled Retard coefficient equivalent value of ADV limit from RON100 Rev limiter #1 Rev limiter #2 Rev limiter #3 Rev limiter recover #1 Rev limiter recover #2 Rev limiter recover #3 Revlimiter 1 Revlimiter 2 Revlimiter 3 Revlimiter 4 Revlimiter 5 Revlimiter 6 Revlimiter 7 Revlimiter Second ECT sensor enabled Secondary oxygen sensor enabled Short term fuel trim maximum Short term fuel trim minimum Soot generation limit CAEX angle table Soot generation limit CAIN angle table Speed limiter rpm Speed limiter speed Speedlimiter Start of injection table 1 Start of injection table 2 Target boost pressure Target discharge amount I Target discharge amount P Target fuel pressure map (high water temp) Target fuel pressure map (low water temp) #1 Target fuel pressure map (low water temp) #2 Target fuel pressure map (low water temp) Target fuel pressure map 3 #1 Target fuel pressure map 3 #2 Target fuel pressure map 3 Target fuel pressure map 4 Target fuel pressure map 5 Target RPM (no load) for throttle target torque rate limit air mass TC boost command TC max boost (EGT) #1 TC max boost (EGT) #2 TC max boost (EGT) #3 TC max boost (EGT) #4 TC max boost (EGT) #5 TC max boost (IAT) #1 TC max boost (PA) TC max boost(EGT) #1 TC max boost(EGT) #2 TC max boost(EGT) #3 TC max boost(EGT) #4 TC max boost(EGT) #5 TC max boost(IAT) #1 TC max boost(IAT) #2 TC max boost(IAT2) #1 TC max boost(IAT2) #2 TC max boost(IAT2) #3 TC max boost(IAT2) #4 TC max boost(IAT2) #5 TC max boost(PA) TC maximum pressure ratio #1 TC maximum pressure ratio #2 Throttle flow vs opening Throttle position at the time of the optimum boost Throttle/brake max something Throttle/brake max speed Torque Limit Warning Turbine overspeed avoidance upper limit Turbo WOT judgment GAIRCYL table Under boost error (P0299) Use MAP to determine WOT(Off=1,On=0) VLFFCR calculation factor VSA enabled VTC enabled(Off=0,On=2) VTEC Engagement VTEC oil pressure switch enabled Waste gate command map Water temperature ignition compensation cold high load Water temperature ignition compensation cold high Water temperature ignition compensation cold low load Water temperature ignition compensation cold low Water temperature ignition compensation hot high load Water temperature ignition compensation hot high Water temperature ignition compensation hot low load Water temperature ignition compensation hot low WOT determination (mg/cyl) WOT lambda adjustment #1 WOT lambda adjustment #2 WOT lambda adjustment #3 WOT lambda adjustment high #1 WOT lambda adjustment high #2 WOT lambda adjustment high #3 WOT lambda adjustment low #1 WOT lambda adjustment low #2 WOT lambda adjustment low #3 WOT rich limit Write security word #1 Write security word #2 Write security word #3