-- MIB file created 07-Aug-2002 10:53:24, by -- SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com CISCO-ATM-IF-MIB DEFINITIONS ::= BEGIN -- From file: "CISCO-ATM-IF-MIB.my" -- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T" IMPORTS TruthValue FROM SNMPv2-TC-v1 ciscoExperiment FROM CISCO-SMI Counter, Gauge FROM RFC1155-SMI ifIndex FROM IF-MIB OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215; ciscoAtmIfMIB OBJECT IDENTIFIER ::= { ciscoExperiment 14 } -- MODULE-IDENTITY -- LastUpdated -- 200202130000Z -- OrgName -- Cisco Systems, Inc. -- ContactInfo -- Cisco Systems -- Customer Service -- -- Postal: 170 W Tasman Drive -- San Jose, CA 95134 -- USA -- -- Tel: +1 800 553-NETS -- -- E-mail: cs-atm@cisco.com -- Descr -- A MIB module for an ATM interface configuration. -- RevDate -- 200202130000Z -- RevDescr -- Deprecated ciscoAtmIfSvcMinVci in favor of object -- ciscoatmInterfaceConfMinSvccVcc with greater -- capability in the CISCO-ATM2-MIB. -- -- Added a notification object to send out a trap -- when ILMI or SSCOP changes state. Also adding an -- object to enable or disable this notification. -- RevDate -- 200108080000Z -- RevDescr -- Added enum aini for the object ciscoAtmIfType. -- RevDate -- 200105210000Z -- RevDescr -- Add new per-service category SVC UPC Intent objects -- ciscoAtmIfSvcUpcIntentCbr, ciscoAtmIfSvcUpcIntentVbrRt, -- ciscoAtmIfSvcUpcIntentVbrNrt, ciscoAtmIfSvcUpcIntentAbr, -- ciscoAtmIfSvcUpcIntentUbr. Deprecate the old per-interface -- SVC UPC intent object ciscoAtmIfSvcUpcIntent. -- RevDate -- 200004110000Z -- RevDescr -- Added -- o A collection of objects that count UPC violations -- and number of cells discarded due to various -- conditions on ATM interfaces. -- o Added ILMI state and SSCOP state monitoring -- variables. -- o Fixed the lines in DESCRIPTION section for -- various objects that failed the line length check -- by mib-police. -- o Introduced a new Group object to obsolete -- ciscoAtmIfMIBGroup3 as it contained objects with -- incompatible status. -- RevDate -- 9903110000Z -- RevDescr -- Clarified the description of SVC UPC Intent object that -- it is defined for logical ATM interfaces too. -- RevDate -- 9711300000Z -- RevDescr -- Added -- ciscoAtmIfConfigAESA -- ciscoAtmIfDerivedAESA -- ciscoAtmIfE164Address -- ciscoAtmIfE164AutoConversionOnly -- objects. -- RevDate -- 9709100000Z -- RevDescr -- Updated description of ciscoAtmIfSignallingAdminStatus -- object. Restriction that the object value be modified -- only when the ifAdminStatus is down has been removed. -- RevDate -- 9611010000Z -- RevDescr -- Added Nsap Address and Well Known VC configuration -- variables. -- RevDate -- 9610140000Z -- RevDescr -- Added SVC UPC intent configuration variable. ciscoAtmIfMIBObjects OBJECT IDENTIFIER ::= { ciscoAtmIfMIB 1 } ciscoAtmIfMIBNotifications OBJECT IDENTIFIER ::= { ciscoAtmIfMIB 0 } ciscoAtmIfMIBConformance OBJECT IDENTIFIER ::= { ciscoAtmIfMIB 3 } ciscoAtmIfMIBCompliances OBJECT IDENTIFIER ::= { ciscoAtmIfMIBConformance 1 } ciscoAtmIfMIBGroups OBJECT IDENTIFIER ::= { ciscoAtmIfMIBConformance 2 } NsapAtmAddr ::= OCTET STRING(SIZE(20)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The ATM address used by the network entity. The -- address types are NSAP (20 octets). AtmAddr ::= OCTET STRING(SIZE(0|8|13|20)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The ATM address used by the network entity. The -- address types are: no address (0 octets), E.164 (8 -- octets), network prefix (13 octets), and NSAP (20 -- octets). Note: The E.164 address is encoded in -- BCD format. UpcMethod ::= INTEGER { passing(1), tagging(2), dropping(3) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- A textual convention defining options for Usage Parameter -- Control: -- passing : take no action on cells considered to violate the -- traffic contract. -- tagging : set the CLP bit in the header of cells considered -- to violate the traffic contract. -- dropping: discard cells considered to violate the traffic -- contract. ciscoAtmIfIlmiAccessGlobalDefaultFilter OBJECT-TYPE SYNTAX INTEGER { permitAll(1), permitPrefix(2), permitPrefixAndWellknownGroups(3), permitPrefixAndAllGroups(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The global default access filter which set the per-switch default access filter for ILMI address registration on all interfaces. permitAll - This permits all ILMI registered addresses. permitPrefix - The address being registered by ILMI should have their prefix portion of the address match the ILMI prefixes used on this interface. If there are any per-interface ILMI address prefixes configured, then the prefixes derived from the switch addresses are not considered ILMI prefixes for this interface. permitPrefixAndWellknownGroups - This is same as 'permitPrefix' but in addition it also allows the well-known group addresses. The well-known group addresses will be the old LECS address and any address matching the ATM Forum address prefix for well known addresses. (i.e.,C5.0079.0000.0000.0000.0000.0000.00A03E) permitPrefixAndAllGroups - This is same as 'permitPrefix' but in addition it allows all group addresses." DEFVAL { permitAll } ::= { ciscoAtmIfMIBObjects 2 } ciscoAtmIfNotifsEnabled OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Allows enabling/disabling of notifications for ATM Interface events" DEFVAL { false } ::= { ciscoAtmIfMIBObjects 3 } ciscoAtmIfTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoAtmIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table contains ATM local interface configuration parameters, one entry per ATM interface port." ::= { ciscoAtmIfMIBObjects 1 } ciscoAtmIfEntry OBJECT-TYPE SYNTAX CiscoAtmIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION " This list conatins additonal ATM interface configuration parameters and state variables." INDEX { ifIndex } -- Augments atmInterfaceConfEntry FROM ATM-MIB ::= { ciscoAtmIfTable 1 } CiscoAtmIfEntry ::= SEQUENCE { ciscoAtmIfType INTEGER, ciscoAtmIfSide INTEGER, ciscoAtmIfUniType INTEGER, ciscoAtmIfPVPs INTEGER, ciscoAtmIfPVCs INTEGER, ciscoAtmIfActiveSVPs Gauge, ciscoAtmIfActiveSVCs Gauge, ciscoAtmIfTotalConnections Gauge, ciscoAtmIfConfVplIf INTEGER, ciscoAtmIfPortType INTEGER, ciscoAtmIfXmitLed INTEGER, ciscoAtmIfRecvLed INTEGER, ciscoAtmIfXmitCells Counter, ciscoAtmIfRecvCells Counter, ciscoAtmIfSvcMinVci INTEGER, ciscoAtmIfIlmiConfiguration INTEGER, ciscoAtmIfIlmiAddressRegistration INTEGER, ciscoAtmIfIlmiAutoConfiguration INTEGER, ciscoAtmIfIlmiKeepAlive INTEGER, ciscoAtmIfSoftVcDestAddress NsapAtmAddr, ciscoAtmIfUniSignallingVersion INTEGER, ciscoAtmIfSvcUpcIntent INTEGER, ciscoAtmIfAddressType INTEGER, ciscoAtmIfAddress OCTET STRING, ciscoAtmIfWellKnownVcMode INTEGER, ciscoAtmIfSignallingAdminStatus INTEGER, ciscoAtmIfCdLed INTEGER, ciscoAtmIfIlmiAccessFilter INTEGER, ciscoAtmIfConfigAESA OCTET STRING, ciscoAtmIfDerivedAESA AtmAddr, ciscoAtmIfE164Address AtmAddr, ciscoAtmIfE164AutoConversionOnly TruthValue, ciscoAtmIfRxCellUpcViolations Counter, ciscoAtmIfRxCellDiscards Counter, ciscoAtmIfIlmiFSMState INTEGER, ciscoAtmIfIlmiUpDownChanges Counter, ciscoAtmIfSscopFSMState INTEGER, ciscoAtmIfSscopUpDownChanges Counter, ciscoAtmIfSvcUpcIntentCbr UpcMethod, ciscoAtmIfSvcUpcIntentVbrRt UpcMethod, ciscoAtmIfSvcUpcIntentVbrNrt UpcMethod, ciscoAtmIfSvcUpcIntentAbr UpcMethod, ciscoAtmIfSvcUpcIntentUbr UpcMethod } ciscoAtmIfType OBJECT-TYPE SYNTAX INTEGER { other(1), uni(2), pnni(3), iisp(4), nniPvcOnly(5), aini(6) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of ATM interface which is either a UNI (User to Network), PNNI, IISP or NNI PVC only. To modify the ciscoAtmIftype, ifAdminStatus has to be down and atmIfIlmiAutoConfiguration disabled." DEFVAL { uni } ::= { ciscoAtmIfEntry 1 } ciscoAtmIfSide OBJECT-TYPE SYNTAX INTEGER { user(1), network(2), notApplicable(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The side of ATM interface which is either a user or network side.NotApplicable value implies that ciscoAtmIftype is other than uni or iisp." DEFVAL { network } ::= { ciscoAtmIfEntry 2 } ciscoAtmIfUniType OBJECT-TYPE SYNTAX INTEGER { public(1), private(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of User to Network interface is either private or public. If ciscoAtmIfType is not uni then ciscoAtmIfUniType value should be ignored." DEFVAL { private } ::= { ciscoAtmIfEntry 3 } ciscoAtmIfPVPs OBJECT-TYPE SYNTAX INTEGER(0..255) ACCESS read-only STATUS mandatory DESCRIPTION "The number of permanent virtual paths at this interface." ::= { ciscoAtmIfEntry 4 } ciscoAtmIfPVCs OBJECT-TYPE SYNTAX INTEGER(0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The number of permanent virtual channels at this interface." ::= { ciscoAtmIfEntry 5 } ciscoAtmIfActiveSVPs OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The number of active switched virtual paths at this interface." ::= { ciscoAtmIfEntry 6 } ciscoAtmIfActiveSVCs OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The number of active switched virtual channels at this interface." ::= { ciscoAtmIfEntry 7 } ciscoAtmIfTotalConnections OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The total number of existing connections at this interface." ::= { ciscoAtmIfEntry 8 } ciscoAtmIfConfVplIf OBJECT-TYPE SYNTAX INTEGER(0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The number of configured VP interfaces at this physical interface." ::= { ciscoAtmIfEntry 9 } ciscoAtmIfPortType OBJECT-TYPE SYNTAX INTEGER { other(1), cpu(2), ethernet(3), oc3Utp(4), oc3SingleModeFiber(5), oc3MultiModeFiber(6), oc12SingleModeFiber(7), ds3(8), e3(9), ds1(10), e1(11), oc3Utp3(12), oc3Utp5(13), oc3SmIr(14), oc3SmIrPlus(15), oc3SmLr(16), oc3Pof(17), oc12MultiModeFiber(18), oc12SmIr(19), oc12SmIrPlus(20), oc12SmLr(21), oc12Pof(22), oc12SmLr2(23), oc12SmLr3(24), atm25(25) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of physical layer medium on the port." ::= { ciscoAtmIfEntry 10 } ciscoAtmIfXmitLed OBJECT-TYPE SYNTAX INTEGER { off(1), steadyGreen(2), steadyYellow(3), steadyRed(4), flashGreen(5), flashYellow(6), flashRed(7) } ACCESS read-only STATUS mandatory DESCRIPTION "The transmit LED color of this port." ::= { ciscoAtmIfEntry 11 } ciscoAtmIfRecvLed OBJECT-TYPE SYNTAX INTEGER { off(1), steadyGreen(2), steadyYellow(3), steadyRed(4), flashGreen(5), flashYellow(6), flashRed(7) } ACCESS read-only STATUS mandatory DESCRIPTION "The receive LED color of this port." ::= { ciscoAtmIfEntry 12 } ciscoAtmIfXmitCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of cells transmitted of this interface, including p2p and p2mp cells." ::= { ciscoAtmIfEntry 13 } ciscoAtmIfRecvCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of cells received of this interface, including p2p and p2mp cells." ::= { ciscoAtmIfEntry 14 } ciscoAtmIfSvcMinVci OBJECT-TYPE SYNTAX INTEGER(0..255) ACCESS read-only STATUS deprecated DESCRIPTION "The minimum of the range of values from which VCI's are assigned to new SVC connections. By this value being larger, more VCI's are reserved for setting up PVCs. This applies to every VPI of the physical interface and every logical port. The object is deprecated because it is recommended to use ciscoAtmInterfaceConfMinSvccVci of the CISCO-ATM2-MIB which is meant for the same purpose." ::= { ciscoAtmIfEntry 15 } ciscoAtmIfIlmiConfiguration OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable ILMI configuration on this interface. The configuration takes effect only on the next interface restart. Disabling this object will also disable atmIfIlmiAddressRegistration and atmIfIlmiAutoConfiguration and atmIfIlmiKeepAlive" DEFVAL { disabled } ::= { ciscoAtmIfEntry 16 } ciscoAtmIfIlmiAddressRegistration OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable ILMI Address Registration on on this interface. The configuration takes effect only on the next interface restart." DEFVAL { disabled } ::= { ciscoAtmIfEntry 17 } ciscoAtmIfIlmiAutoConfiguration OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable ILMI link and interface type determination. The configuration takes effect only on the next interface restart." DEFVAL { disabled } ::= { ciscoAtmIfEntry 18 } ciscoAtmIfIlmiKeepAlive OBJECT-TYPE SYNTAX INTEGER(0..65535) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "The amount of time that should elapse between successive ILMI keepalive messages sent on this interface. A value of 0 disables ILMI keepalive messages on this interface." DEFVAL { 0 } ::= { ciscoAtmIfEntry 19 } ciscoAtmIfSoftVcDestAddress OBJECT-TYPE SYNTAX NsapAtmAddr -- Rsyntax OCTET STRING(SIZE(20)) ACCESS read-only STATUS mandatory DESCRIPTION "The 20 byte ATM address of the destination ATM interface for soft ATM PVC/PVP" ::= { ciscoAtmIfEntry 20 } ciscoAtmIfUniSignallingVersion OBJECT-TYPE SYNTAX INTEGER { notApplicable(1), atmfUni3Dot0(2), atmfUni3Dot1(3), atmfUni4Dot0(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The version of UNI signalling that is currently being used on the interface. The appropriate value, either atmfUni3Dot0, atmfUni3Dot1 or atmfUni4Dot0, is used when the interface is an UNI or IISP interface. The value notApplicable is used when the interface is a PNNI interface or when signalling is disabled. This may reflect a manually configured value for the signalling version, or may be determined by other means such as auto-configuration.Setting this variable to a value of 'notApplicable' is not allowed. To modify the ciscoAtmIfUniSignallingVersion, ifAdminStatus has to be down and atmIfIlmiAutoConfiguration disabled." ::= { ciscoAtmIfEntry 21 } ciscoAtmIfSvcUpcIntent OBJECT-TYPE SYNTAX INTEGER { passing(1), tagging(2), dropping(3) } ACCESS read-write STATUS deprecated DESCRIPTION "Determines the policing (Usage Parameter Control or UPC) action to take for SVCs established through this interface. Values other than passing are allowed only if policing is supported on the interface. Also serves to determine UPC to use on the terminating (destination) half-leg of Soft PVCs. This object has been deprecated in favor of the per-service category objects ciscoAtmIfSvcUpcIntentCbr, ciscoAtmIfSvcUpcIntentVbrRt, ciscoAtmIfSvcUpcIntentVbrNrt, ciscoAtmIfSvcUpcIntentAbr, ciscoAtmIfSvcUpcIntentUbr. Note that if those objects are set to different values, the return value for this object cannot be correct." DEFVAL { passing } ::= { ciscoAtmIfEntry 22 } ciscoAtmIfAddressType OBJECT-TYPE SYNTAX INTEGER { nsap(1), esi(2), e164(3), null(4) } ACCESS read-write STATUS obsolete DESCRIPTION "An indication of the type of the ATM addresses on this interface. To configure a new atm address, set ciscoAtmIfAddress to the address, then set this object to ether nsap(1), or esi(2), or e164(3), depending on the type of address of ciscoAtmIfAddress. To delete the address, set this object to null(4). Adding nsap address type to this interface has the effect of canceling the existing esi address, if there is one. Similarly, adding the esi address on this interface also has the effect of removing the existing nsap address. The value of ciscoAtmIfAddress has no effect when this object is set to null(4). For the switch, the nsap/esi address can only exist on the cpu port for signalling applications." ::= { ciscoAtmIfEntry 23 } ciscoAtmIfAddress OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0|6|8|20)) ACCESS read-write STATUS obsolete DESCRIPTION "The ATM address of this interface, which can be either nsap, esi or e164. For the switch, the nsap/esi address can only exist on the cpu port." ::= { ciscoAtmIfEntry 24 } ciscoAtmIfWellKnownVcMode OBJECT-TYPE SYNTAX INTEGER { automatic(1), manual(2), manualDeleteUponEntry(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether well-known VCs should be automatically or manually created for the interface. In automatic(1) mode, well-known VCs will be created with default VPI/VCI values upon startup or upon entry to the automatic mode. While in this mode, well-known VCs will not be allowed to be deleted or modified by user commands. This is the default mode at startup for equipment which supports automatic well-known VC creation. In manual(2) mode, well-known VCs won't be automatically created. Instead, the user will be allowed to delete and create PVCs with the reserved encapsulation types aalQsAal, aal5Ilmi, and aal5Pnni as applicable. And these PVCs will be allowed to have VCI values in the range <5-16383>, instead of <32-16383>. The manualDeleteUponEntry(3) action causes any existing VCs with reserved encapsulation types (aalQsAal, aal5Ilmi or aal5Pnni) to be deleted for this interface as it enters the manual state." DEFVAL { automatic } ::= { ciscoAtmIfEntry 31 } ciscoAtmIfSignallingAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable signalling/sscop on this interface.The disabled(2) action causes all the active SVCs on this interface to be cleared." DEFVAL { enabled } ::= { ciscoAtmIfEntry 32 } ciscoAtmIfCdLed OBJECT-TYPE SYNTAX INTEGER { off(1), steadyGreen(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The Cd LED color of this port." ::= { ciscoAtmIfEntry 33 } ciscoAtmIfIlmiAccessFilter OBJECT-TYPE SYNTAX INTEGER { permitAll(1), permitPrefix(2), permitPrefixAndWellknownGroups(3), permitPrefixAndAllGroups(4), useGlobalDefaultFilter(5) } ACCESS read-write STATUS mandatory DESCRIPTION "The access filter which allows or denies certain ILMI registered addresses on this interface when ciscoAtmIfIlmiAddressRegistration is set to enable(1). permitAll - This permits all ILMI registered addresses. permitPrefix - The address being registered by ILMI should have their prefix portion of the address match the ILMI prefixes used on this interface. If there are any per-interface ILMI address prefixes configured, then the prefixes derived from the switch addresses are not considered ILMI prefixes for this interface. permitPrefixAndWellknownGroups - This is same as 'permitPrefix' but in addition it also allows the well-known group addresses. The well-known group addresses will be the old LECS address and any address matching the ATM Forum address prefix for well known addresses. (i.e.,C5.0079.0000.0000.0000.0000.0000.00A03E) permitPrefixAndAllGroups - This is same as 'permitPrefix' but in addition it allows all group addresses. useGlobalDefaultFilter - It indicates that this interface uses the per-switch global default filter" DEFVAL { useGlobalDefaultFilter } ::= { ciscoAtmIfEntry 34 } ciscoAtmIfConfigAESA OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0|7|20)) ACCESS read-write STATUS mandatory DESCRIPTION "The ATM End System Address (AESA) of this interface can be configured by entering the full 20 octet AESA, or the 6 octet ESI and 1 octet Selector Byte. If the ESI and Selector Byte are entered, the full AESA will be formed using a 13 octet prefix from ILMI. The full AESA can be read using ciscoAtmIfDerivedAESA. A length of zero indicates that no AESA is configured. For the switch, the AESA address can only exist on the cpu port." ::= { ciscoAtmIfEntry 35 } ciscoAtmIfDerivedAESA OBJECT-TYPE SYNTAX AtmAddr -- Rsyntax OCTET STRING(SIZE(0|8|13|20)) ACCESS read-only STATUS mandatory DESCRIPTION "The ATM End System Address (AESA) of this interface. The AESA is configured using ciscoAtmIfConfigAESA or can be automatically generated. A length of zero indicates that no AESA is specified. For the switch, the AESA address can only exist on the cpu port." ::= { ciscoAtmIfEntry 36 } ciscoAtmIfE164Address OBJECT-TYPE SYNTAX AtmAddr -- Rsyntax OCTET STRING(SIZE(0|8|13|20)) ACCESS read-write STATUS mandatory DESCRIPTION "The ATM E164 address of this interface. When a native E.164 number is configured for this inteface, only native E.164 numbers are transmitted/received as the called/calling party numbers. The presence of an ATM E164 address allows both an algorithmic translation between the native E164 number and E164 AESA address formats (see ciscoAtmIfE164AutoConversionOnly) and use of the ATM E164 Address for the calling/called party number of transmitted/received calls. Entering an address will disable ciscoAtmIfE164AutoConversionOnly. An address of length zero indicates that no address is specified. For the switch, the E164 address cannot exist on the cpu port." ::= { ciscoAtmIfEntry 37 } ciscoAtmIfE164AutoConversionOnly OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable E164 auto conversion only on this interface. The E164 auto-conversion allows for algorithmic translation between the native E164 number and E164 AESA address formats. This object is used when there is no native E.164 number specified for this interface (see ciscoAtmIfE164Address), to specify that only native E.164 numbers are transmitted/received as the called/calling party numbers and to enable/disable E164 auto-conversion. For the switch, E164 auto-conversion cannot exist on the cpu port." ::= { ciscoAtmIfEntry 38 } ciscoAtmIfRxCellUpcViolations OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this interface. This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmIfEntry 39 } ciscoAtmIfRxCellDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of cells that were discarded within the switch. The cells can be discarded due to non conformance detected by Usage Parameter Control (UPC) or queue overflows within the switch. This object is not instantiated on systems that do not have support for collecting such statistics." ::= { ciscoAtmIfEntry 40 } ciscoAtmIfIlmiFSMState OBJECT-TYPE SYNTAX INTEGER { down(1), restarting(2), waitDevType(3), deviceAndPortTypeComplete(4), awaitPnniConfig(5), pnniConfigComplete(6), awaitRestartAck(7), upAndNormal(8) } ACCESS read-only STATUS mandatory DESCRIPTION "The ILMI states meaningful when the value of ciscoAtmIfIlmiConfiguration indicates that the ILMI is enabled for an ATM interface: down -- Stopped or just booted or interface down restarting -- Establishing link connectivity waitDevType -- Awaiting device type from peer deviceAndPortTypeComplete -- Determined device and/or port type awaitPnniConfig -- Awaiting PNNI configuration from peer pnniConfigComplete -- Completed interface PNNI configuration awaitRestartAck -- Awaiting peer range values after restart upAndNormal -- Up and normal." ::= { ciscoAtmIfEntry 41 } ciscoAtmIfIlmiUpDownChanges OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times ILMI enters and leaves the state of upAndNormal." ::= { ciscoAtmIfEntry 42 } ciscoAtmIfSscopFSMState OBJECT-TYPE SYNTAX INTEGER { idle(1), outgoingConnectionPending(2), incomingConnectionPending(3), dataTransferReady(4), outgoingDisconnectionPending(5), outgoingResyncPending(6), incomingResyncPending(7), outgoingRecoveryPending(8), incomingRecoveryPending(9), concurrentResyncPending(10) } ACCESS read-only STATUS mandatory DESCRIPTION "The SSCOP state for an ATM interface as defined by the ITU-T. The state is idle when the interface is down or SSCOP is not enabled on the ATM interface" REFERENCE "ITU-T Recommendation Q.2110 (07/94)" ::= { ciscoAtmIfEntry 43 } ciscoAtmIfSscopUpDownChanges OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times SSCOP enters and leaves the state of DataTransferReady." ::= { ciscoAtmIfEntry 44 } ciscoAtmIfSvcUpcIntentCbr OBJECT-TYPE SYNTAX UpcMethod -- Rsyntax INTEGER { -- passing(1), -- tagging(2), -- dropping(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the policing (Usage Parameter Control or UPC) action to take for Constant Bit Rate SVCs established through this interface. Values other than passing are allowed only if policing is supported on the interface. Also serves to determine UPC to use on the terminating (destination) half-leg of Soft PVCs." DEFVAL { passing } ::= { ciscoAtmIfEntry 45 } ciscoAtmIfSvcUpcIntentVbrRt OBJECT-TYPE SYNTAX UpcMethod -- Rsyntax INTEGER { -- passing(1), -- tagging(2), -- dropping(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the policing (Usage Parameter Control or UPC) action to take for Variable Bit Rate - Real Time SVCs established through this interface. Values other than passing are allowed only if policing is supported on the interface. Also serves to determine UPC to use on the terminating (destination) half-leg of Soft PVCs." DEFVAL { passing } ::= { ciscoAtmIfEntry 46 } ciscoAtmIfSvcUpcIntentVbrNrt OBJECT-TYPE SYNTAX UpcMethod -- Rsyntax INTEGER { -- passing(1), -- tagging(2), -- dropping(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the policing (Usage Parameter Control or UPC) action to take for Variable Bit Rate - Non Real Time SVCs established through this interface. Values other than passing are allowed only if policing is supported on the interface. Also serves to determine UPC to use on the terminating (destination) half-leg of Soft PVCs." DEFVAL { passing } ::= { ciscoAtmIfEntry 47 } ciscoAtmIfSvcUpcIntentAbr OBJECT-TYPE SYNTAX UpcMethod -- Rsyntax INTEGER { -- passing(1), -- tagging(2), -- dropping(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the policing (Usage Parameter Control or UPC) action to take for Available Bit Rate SVCs established through this interface. Values other than passing are allowed only if policing is supported on the interface. Also serves to determine UPC to use on the terminating (destination) half-leg of Soft PVCs." DEFVAL { passing } ::= { ciscoAtmIfEntry 48 } ciscoAtmIfSvcUpcIntentUbr OBJECT-TYPE SYNTAX UpcMethod -- Rsyntax INTEGER { -- passing(1), -- tagging(2), -- dropping(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the policing (Usage Parameter Control or UPC) action to take for Unspecified Bit Rate SVCs established through this interface. Values other than passing are allowed only if policing is supported on the interface. Also serves to determine UPC to use on the terminating (destination) half-leg of Soft PVCs." DEFVAL { passing } ::= { ciscoAtmIfEntry 49 } ciscoAtmIfEvent TRAP-TYPE -- Reverse mappable trap ENTERPRISE ciscoAtmIfMIB VARIABLES { ciscoAtmIfIlmiFSMState, ciscoAtmIfSscopFSMState } -- Status -- mandatory DESCRIPTION "This notification is generated when ever ILMI or SSCOP FSM state changes" ::= 1 ciscoAtmIfMIBGroup OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 1 } -- OBJECT-GROUP -- Status -- deprecated -- Descr -- A collection of objects providing the information -- about ATM interface related information also an -- ability to configure certain parameters of -- ATM interface. -- objects -- ciscoAtmIfType, ciscoAtmIfSide, ciscoAtmIfUniType, -- ciscoAtmIfPVPs, ciscoAtmIfPVCs, ciscoAtmIfActiveSVPs, -- ciscoAtmIfActiveSVCs, ciscoAtmIfTotalConnections, -- ciscoAtmIfConfVplIf, ciscoAtmIfPortType, ciscoAtmIfXmitLed, -- ciscoAtmIfRecvLed, ciscoAtmIfXmitCells, ciscoAtmIfRecvCells, -- ciscoAtmIfSvcMinVci, ciscoAtmIfIlmiConfiguration, -- ciscoAtmIfIlmiAddressRegistration, -- ciscoAtmIfIlmiAutoConfiguration, ciscoAtmIfIlmiKeepAlive, -- ciscoAtmIfSoftVcDestAddress, ciscoAtmIfCdLed ciscoAtmIfMIBGroup2 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 2 } -- OBJECT-GROUP -- Status -- deprecated -- Descr -- Additional collection of objects providing -- ATM interface related information. -- objects -- ciscoAtmIfUniSignallingVersion, ciscoAtmIfSvcUpcIntent ciscoAtmIfMIBGroup3 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 3 } -- OBJECT-GROUP -- Status -- obsolete -- Descr -- Additional collection of objects providing ATM -- interface related information. -- objects -- ciscoAtmIfAddressType, ciscoAtmIfAddress, -- ciscoAtmIfWellKnownVcMode, ciscoAtmIfSignallingAdminStatus ciscoAtmIfMIBGroup4 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 4 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- Additional collection of objects providing ATM -- switch and interface related information on Access -- Filter for ILMI Address Registration. -- objects -- ciscoAtmIfIlmiAccessGlobalDefaultFilter, -- ciscoAtmIfIlmiAccessFilter ciscoAtmIfMIBGroup5 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 5 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- Additional collection of objects providing ATM -- switch and interface related information for ATM Addresses. -- objects -- ciscoAtmIfConfigAESA, ciscoAtmIfDerivedAESA, -- ciscoAtmIfE164Address, ciscoAtmIfE164AutoConversionOnly ciscoAtmIfMIBGroup6 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 6 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- Additional collection of objects providing ATM -- interface related information. -- objects -- ciscoAtmIfWellKnownVcMode, ciscoAtmIfSignallingAdminStatus ciscoAtmIfMIBGroup7 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 7 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- Additional collection of objects providing ATM switch -- interface Resource Manager, ILMI and Signalling related -- information. -- objects -- ciscoAtmIfRxCellUpcViolations, ciscoAtmIfRxCellDiscards, -- ciscoAtmIfIlmiFSMState, ciscoAtmIfIlmiUpDownChanges, -- ciscoAtmIfSscopFSMState, ciscoAtmIfSscopUpDownChanges ciscoAtmIfMIBGroup8 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 8 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- Additional collection of objects providing -- ATM interface related information. -- objects -- ciscoAtmIfUniSignallingVersion, ciscoAtmIfSvcUpcIntentCbr, -- ciscoAtmIfSvcUpcIntentVbrRt, ciscoAtmIfSvcUpcIntentVbrNrt, -- ciscoAtmIfSvcUpcIntentAbr, ciscoAtmIfSvcUpcIntentUbr ciscoAtmIfMIBGroup9 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 9 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects providing the information -- about ATM interface related information also an -- ability to configure certain parameters of -- ATM interface. -- objects -- ciscoAtmIfType, ciscoAtmIfSide, ciscoAtmIfUniType, -- ciscoAtmIfPVPs, ciscoAtmIfPVCs, ciscoAtmIfActiveSVPs, -- ciscoAtmIfActiveSVCs, ciscoAtmIfTotalConnections, -- ciscoAtmIfConfVplIf, ciscoAtmIfPortType, ciscoAtmIfXmitLed, -- ciscoAtmIfRecvLed, ciscoAtmIfXmitCells, ciscoAtmIfRecvCells, -- ciscoAtmIfIlmiConfiguration, -- ciscoAtmIfIlmiAddressRegistration, -- ciscoAtmIfIlmiAutoConfiguration, ciscoAtmIfIlmiKeepAlive, -- ciscoAtmIfSoftVcDestAddress, ciscoAtmIfCdLed ciscoAtmIfMIBGroup10 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 10 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- Additional objects providing means to enable/disable -- notifications related to the interface ILMI and -- SSCOP state -- objects -- ciscoAtmIfNotifsEnabled ciscoAtmIfNotifyGroup OBJECT IDENTIFIER ::= { ciscoAtmIfMIBGroups 11 } -- NOTIFICATION-GROUP -- Status -- mandatory -- Descr -- Interface ILMI and SSCOP FSM notifications -- notifications -- ciscoAtmIfEvent ciscoAtmIfMIBCompliance OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 1 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup ciscoAtmIfMIBCompliance2 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 2 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup -- MandGroup -- ciscoAtmIfMIBGroup2 ciscoAtmIfMIBCompliance3 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 3 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup -- MandGroup -- ciscoAtmIfMIBGroup2 -- MandGroup -- ciscoAtmIfMIBGroup3 ciscoAtmIfMIBCompliance4 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 4 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup -- MandGroup -- ciscoAtmIfMIBGroup2 -- MandGroup -- ciscoAtmIfMIBGroup3 -- MandGroup -- ciscoAtmIfMIBGroup4 ciscoAtmIfMIBCompliance5 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 5 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup -- MandGroup -- ciscoAtmIfMIBGroup2 -- MandGroup -- ciscoAtmIfMIBGroup3 -- MandGroup -- ciscoAtmIfMIBGroup4 -- MandGroup -- ciscoAtmIfMIBGroup5 ciscoAtmIfMIBCompliance6 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 6 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup -- MandGroup -- ciscoAtmIfMIBGroup2 -- MandGroup -- ciscoAtmIfMIBGroup4 -- MandGroup -- ciscoAtmIfMIBGroup5 -- MandGroup -- ciscoAtmIfMIBGroup6 -- MandGroup -- ciscoAtmIfMIBGroup7 ciscoAtmIfMIBCompliance7 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 7 } -- MODULE-COMPLIANCE -- Status -- deprecated -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup -- MandGroup -- ciscoAtmIfMIBGroup4 -- MandGroup -- ciscoAtmIfMIBGroup5 -- MandGroup -- ciscoAtmIfMIBGroup6 -- MandGroup -- ciscoAtmIfMIBGroup7 -- MandGroup -- ciscoAtmIfMIBGroup8 ciscoAtmIfMIBCompliance8 OBJECT IDENTIFIER ::= { ciscoAtmIfMIBCompliances 8 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for the Cisco ATM -- interface group. -- Module -- >>current<< -- MandGroup -- ciscoAtmIfMIBGroup4 -- MandGroup -- ciscoAtmIfMIBGroup5 -- MandGroup -- ciscoAtmIfMIBGroup6 -- MandGroup -- ciscoAtmIfMIBGroup7 -- MandGroup -- ciscoAtmIfMIBGroup8 -- MandGroup -- ciscoAtmIfMIBGroup9 -- MandGroup -- ciscoAtmIfMIBGroup10 -- MandGroup -- ciscoAtmIfNotifyGroup END