-- MIB file created 29-Nov-2005 10:33:43, by -- SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com CISCO-ATM-TRUNK-STAT-MIB DEFINITIONS ::= BEGIN -- From file: "CISCO-ATM-TRUNK-STAT-MIB.my" -- Compile options "4 7 F H N O W 03 06 0B 0G 0N 0T" IMPORTS TruthValue, TimeStamp FROM SNMPv2-TC-v1 ciscoMgmt FROM CISCO-SMI ifIndex FROM IF-MIB AtmVcIdentifier, AtmVpIdentifier FROM ATM-TC-MIB Counter, Gauge FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212; ciscoAtmTrunkStatMIB OBJECT IDENTIFIER ::= { ciscoMgmt 407 } -- MODULE-IDENTITY -- LastUpdated -- 200508100000Z -- OrgName -- Cisco Systems, Inc. -- ContactInfo -- Cisco Systems -- Customer Service -- -- Postal: 170 W Tasman Drive -- San Jose, CA 95134 -- USA -- -- Tel: +1 800 553-NETS -- -- E-mail: cs-wanatm@cisco.com -- Descr -- The MIB module contains ATM Trunk statistics. -- -- TERMINOLOGY -- =========== -- PVC: Permanent Virtual Circuit -- OAM: Operation and Management -- CRC: Cyclic redundancy check -- AIS: Alarm Indication Signal -- TDM: Time Division Multiplex -- FERF: Far End Receive Failure -- CPS: Common Part Sub-layer -- PDU: Protocol Data Unit -- HEC: Header Error Control -- DSP: Digital Signal Processing -- CID: Channel Identifier -- UUI: User-to-User Information -- VoIP: Voice over IP -- CCS: Common Channel Signaling -- VoAAL2: Voice over AAL2 -- SDU: Service Data Unit -- HDLC: High Level Data Link Control -- SAR: Segmantation and Reassembly -- -- External AIS - is an Alarm Indication Signal associated -- with a maintenance alarm detected on a defective -- maintenance span, that is transmitted in the direction -- of the defect as a substitute for normal signal. -- The purpose is to show the downstream entities that -- a defect has been identified and to prevent other -- maintenance alarms consequent to this first defect. -- External AIS bit stream is represented by an all 1's -- signal. -- Ref - ITU-T Rec. M.20 sec. 5.4.2 a -- -- External RAI - is a Remote Alarm Indication signal -- that is transmitted upstream from an entity that has -- detected defects persisting long enough to constitute -- a received signal failure. Its purpose is to report in -- the backward direction that there is an interruption -- of service in the forward direction. -- The forward direction is from the originating end of -- the alarm to the remote end. -- The backward direction is from the remote end to the -- orginating end of the alarm. -- Ref - ITU-T Rec. G.704 section 2.1.3.1.3 -- I.366.2 - ANNEX N -- -- External Connection AIS - is a Alarm Indicating Signal -- transmitted in the downstream direction from the AAL -- type 2 connecting point that first detects a defect -- affecting the AAL type 2 connection; this includes -- defects indicated by lower layers. -- Ref - ITU-T Rec. I.610 sec 6.2.2.1.1.1 -- -- External Connection RDI - is a signal transmitted upstream -- by an AAl type 2 endpoint that is in an alarm state as the -- result of having received an AAL type2 connection AIS or -- having detected a defect that affects the AAL type2 -- connection. -- -- All ATM alarm definitions are specified in I.610 -- (ITU standard). -- RevDate -- 200508100000Z -- RevDescr -- Add new objects -- - catsPvcOamLpbkTimeoutCnts -- - catsPvcNewOamLpbkTimeoutDur -- - catsPvcActiveOamLpbkTimeoutDur -- - catsPvcOamLpbkTimeoutThreshold -- RevDate -- 200405120000Z -- RevDescr -- Initial version of the MIB. ciscoAtmTrunkStatNotifs OBJECT IDENTIFIER ::= { ciscoAtmTrunkStatMIB 0 } ciscoAtmTrunkStatObjects OBJECT IDENTIFIER ::= { ciscoAtmTrunkStatMIB 1 } catsStatistics OBJECT IDENTIFIER ::= { ciscoAtmTrunkStatObjects 1 } catsMIBConformance OBJECT IDENTIFIER ::= { ciscoAtmTrunkStatMIB 2 } catsMIBGroups OBJECT IDENTIFIER ::= { catsMIBConformance 1 } catsMIBCompliances OBJECT IDENTIFIER ::= { catsMIBConformance 2 } catsPvcHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CatsPvcHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table represents a 24 hour history of statistics per PVC. The statistics are collected using 15 minute intervals. Entries in this table are populated at the end of the interval." ::= { catsStatistics 1 } catsPvcHistoryEntry OBJECT-TYPE SYNTAX CatsPvcHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table. Each entry represents the PVC statistics for a given 15 minute interval. The ifIndex refers to the instance in the ifTable with ifType propAtm(197) or atm(37)." INDEX { ifIndex, catsPvcVpi, catsPvcVci, catsPvcIntervalIndex } ::= { catsPvcHistoryTable 1 } CatsPvcHistoryEntry ::= SEQUENCE { catsPvcVpi AtmVpIdentifier, catsPvcVci AtmVcIdentifier, catsPvcIntervalIndex Gauge, catsPvcValidFlag TruthValue, catsPvcDiscontinuityTime TimeStamp, catsPvcAtmXmtCells Counter, catsPvcAtmRcvCells Counter, catsPvcAvgAtmXmtCells Counter, catsPvcAvgAtmRcvCells Counter, catsPvcPeakAtmXmtCells Counter, catsPvcPeakAtmRcvCells Counter, catsPvcOamXmtEndLpbkCells Counter, catsPvcOamRcvEndLpbkCells Counter, catsPvcOamXmtSegLpbkCells Counter, catsPvcOamRcvSegLpbkCells Counter, catsPvcOamLpbkLostCells Counter, catsPvcDiscardedRcvOamCells Counter, catsPvcAisSuppressCnts Counter, catsPvcXmtAisCnts Counter, catsPvcRcvAisCnts Counter, catsPvcXmtFerfCnts Counter, catsPvcRcvFerfCnts Counter, catsPvcXmtAisCells Counter, catsPvcRcvAisCells Counter, catsPvcXmtFerfCells Counter, catsPvcRcvFerfCells Counter, catsPvcOamLpbkTimeoutCnts Counter, catsPvcNewOamLpbkTimeoutDur Gauge, catsPvcActiveOamLpbkTimeoutDur Gauge, catsPvcOamLpbkTimeoutThreshold Gauge } catsPvcVpi OBJECT-TYPE SYNTAX AtmVpIdentifier -- Rsyntax INTEGER(0..4095) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VPI value for the PVC for which the statistics are being collected." ::= { catsPvcHistoryEntry 1 } catsPvcVci OBJECT-TYPE SYNTAX AtmVcIdentifier -- Rsyntax INTEGER(0..65535) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VCI value for the PVC for which the statistics are being collected." ::= { catsPvcHistoryEntry 2 } catsPvcIntervalIndex OBJECT-TYPE SYNTAX Gauge(1..96) ACCESS not-accessible STATUS mandatory DESCRIPTION "This is the history interval number. The intervals are 15 minutes long and thus for a 24 hour period there will be 96 intervals. The 24 hour interval is aligned to wall clock. The index of 1 will represent the interval from 00:00 to 00:15. The index of 2 will represent the interval from 00:15 to 00:30 and so on. " ::= { catsPvcHistoryEntry 3 } catsPvcValidFlag OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to indicate if the entry has valid statistics data. It contains a value of true(1) if the data is valid and false(2) otherwise. A possible scenario when this flag will be set to false(2) is when there are time changes due to daylight savings time and/ or time zone changes. This flag can also be set to false(2) if the statistics in this 15 minute interval have experienced discontinuity." ::= { catsPvcHistoryEntry 4 } catsPvcDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object will represent the timestamp when the statistics in this 15 minute interval were discontinued due to a forced clear on the module. If this has the default value then it indicates that the statistics in this interval have not experienced any discontinuity." DEFVAL { 0 } ::= { catsPvcHistoryEntry 5 } catsPvcAtmXmtCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of cells transmitted by this PVC towards the ATM network." ::= { catsPvcHistoryEntry 6 } catsPvcAtmRcvCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of cells received by this PVC from the ATM network." ::= { catsPvcHistoryEntry 7 } catsPvcAvgAtmXmtCells OBJECT-TYPE SYNTAX Counter -- Units -- cells-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "The average number of cells transmitted towards the network by this PVC. The average is computed by dividing the total number of cells transmitted over this 15 minute interval by the interval time (15 minutes)." ::= { catsPvcHistoryEntry 8 } catsPvcAvgAtmRcvCells OBJECT-TYPE SYNTAX Counter -- Units -- cells-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "The average number of cells received from the network by the PVC. The average is computed by dividing the total number of cells received over this 15 minute interval by the interval time (15 minutes)." ::= { catsPvcHistoryEntry 9 } catsPvcPeakAtmXmtCells OBJECT-TYPE SYNTAX Counter -- Units -- cells-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "The peak number of cells per second transmitted towards the network. The transmitted cells per second are monitored every second and the peak value over this 15 minute interval is returned in this object." ::= { catsPvcHistoryEntry 10 } catsPvcPeakAtmRcvCells OBJECT-TYPE SYNTAX Counter -- Units -- cells-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "The peak number of cells per second received from the network. The received cells per second are monitored every second and the peak value over this 15 minute interval is returned in this object." ::= { catsPvcHistoryEntry 11 } catsPvcOamXmtEndLpbkCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of OAM end-to-end loopback cells that were transmitted on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 12 } catsPvcOamRcvEndLpbkCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of OAM end-to-end loopback cells that were received on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 13 } catsPvcOamXmtSegLpbkCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of OAM Segment loop back cells that were transmitted on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 14 } catsPvcOamRcvSegLpbkCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of OAM Segment loop back cells that were received on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 15 } catsPvcOamLpbkLostCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object keeps track of the number of OAM loopback cells lost." ::= { catsPvcHistoryEntry 16 } catsPvcDiscardedRcvOamCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of OAM cells that had CRC errors and are not counted in any other counters for received OAM cells." ::= { catsPvcHistoryEntry 17 } catsPvcAisSuppressCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of instances that an ATM AIS alarm was successfully suppressed which prevented the alarm from propagating to the TDM interfaces. " ::= { catsPvcHistoryEntry 18 } catsPvcXmtAisCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of instances that an ATM AIS alarm was transmitted." ::= { catsPvcHistoryEntry 19 } catsPvcRcvAisCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of instances that an ATM AIS alarm was received." ::= { catsPvcHistoryEntry 20 } catsPvcXmtFerfCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of instances that an ATM FERF alarm was transmitted." ::= { catsPvcHistoryEntry 21 } catsPvcRcvFerfCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of instances that an ATM FERF alarm was received." ::= { catsPvcHistoryEntry 22 } catsPvcXmtAisCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AIS cells that were transmitted on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 23 } catsPvcRcvAisCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AIS cells that were received on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 24 } catsPvcXmtFerfCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of FERF cells that were transmitted on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 25 } catsPvcRcvFerfCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of FERF cells that were received on this connection during this 15 minute interval." ::= { catsPvcHistoryEntry 26 } catsPvcOamLpbkTimeoutCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of instances that OAM Loopback Timeout alarm had occurred within this 15 minute interval." ::= { catsPvcHistoryEntry 27 } catsPvcNewOamLpbkTimeoutDur OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "The duration of new OAM Loopback Timeout alarms for this 15 minute interval expressed in seconds." ::= { catsPvcHistoryEntry 28 } catsPvcActiveOamLpbkTimeoutDur OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "The total duration of new and past OAM loopback timeout alarms that were active during this 15 minute interval. For example, if the an alarm lasted for a total of 50 seconds and crossed interval boundaries. In the previous 15 minute interval it lasted for 30 seconds and 20 seconds in the current 15 minute interval. There is a new alarm that lasted for 15 seconds in the current 15 minute interval as well. Thus, this object will have a value of 20+15 = 35 seconds." ::= { catsPvcHistoryEntry 29 } catsPvcOamLpbkTimeoutThreshold OBJECT-TYPE SYNTAX Gauge(1..60) -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "This is the threshold for OAM Loopback Timeout alarm expressed in seconds. If the OAM cell is not received back within the threshold specified in this object, an OAM loopback timeout alarm is generated." DEFVAL { 5 } ::= { catsPvcHistoryEntry 30 } catsAal2PvcHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CatsAal2PvcHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table represents a 24 hour history of statistics per AAL2 PVC. The statistics are collected using 15 minute intervals. Entries in this table are populated at the end of the interval." ::= { catsStatistics 2 } catsAal2PvcHistoryEntry OBJECT-TYPE SYNTAX CatsAal2PvcHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table. Each entry contains the statistics for particular AAL2 PVC for the given 15 minute interval. The primary index, ifIndex, will be of ifType propAtm(197), atm(37) or aal2(187)." INDEX { ifIndex, catsAal2PvcVpi, catsAal2PvcVci, catsAal2PvcIntervalIndex } ::= { catsAal2PvcHistoryTable 1 } CatsAal2PvcHistoryEntry ::= SEQUENCE { catsAal2PvcVpi AtmVpIdentifier, catsAal2PvcVci AtmVcIdentifier, catsAal2PvcIntervalIndex Gauge, catsAal2PvcValidFlag TruthValue, catsAal2PvcDiscontinuityTime TimeStamp, catsAal2PvcCpsSentPkts Counter, catsAal2PvcCpsRcvdPkts Counter, catsAal2PvcHecErrors Counter, catsAal2PvcCrcErrors Counter, catsAal2PvcInvOsfCells Counter, catsAal2PvcInvParCells Counter, catsAal2PvcCpsInvCidPkts Counter, catsAal2PvcCpsInvUuiPkts Counter, catsAal2PvcCpsInvLenPkts Counter } catsAal2PvcVpi OBJECT-TYPE SYNTAX AtmVpIdentifier -- Rsyntax INTEGER(0..4095) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VPI value for the AAL2 PVC for which the statistics are being collected." ::= { catsAal2PvcHistoryEntry 1 } catsAal2PvcVci OBJECT-TYPE SYNTAX AtmVcIdentifier -- Rsyntax INTEGER(0..65535) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VCI value for the AAL2 PVC for which the statistics are being collected." ::= { catsAal2PvcHistoryEntry 2 } catsAal2PvcIntervalIndex OBJECT-TYPE SYNTAX Gauge(1..96) ACCESS not-accessible STATUS mandatory DESCRIPTION "This is the history interval number. The intervals are 15 minutes long and thus for a 24 hour period there will be 96 intervals. The 24 hour interval is aligned to wall clock. The index of 1 will represent the interval from 00:00 to 00:15. The index of 2 will represent the interval from 00:15 to 00:30 and so on." ::= { catsAal2PvcHistoryEntry 3 } catsAal2PvcValidFlag OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to indicate if the entry has valid statistics data. It contains a value of true(1) if the data is valid and false(2) otherwise. A possible scenario when this flag will be set to false(2) is when there are time changes due to daylight savings time and/ or time zone changes. This flag can also be set to false(2) if statistics in this 15 minute interval have experienced discontinuity." ::= { catsAal2PvcHistoryEntry 4 } catsAal2PvcDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object will represent the timestamp when the statistics in this 15 minute interval were discontinued due to a forced clear on the module. If this has the default value then it indicates that the statistics in this interval have not experienced any discontinuity." DEFVAL { 0 } ::= { catsAal2PvcHistoryEntry 5 } catsAal2PvcCpsSentPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL2 CPS packets sent to the network during this 15 minute interval." ::= { catsAal2PvcHistoryEntry 6 } catsAal2PvcCpsRcvdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL2 CPS packets received from the network during this 15 minute interval. This does not include the packets which are counted as error packets." ::= { catsAal2PvcHistoryEntry 7 } catsAal2PvcHecErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of egress AAL2(ATM Adaptation layer 2) CPS PDU dropped due to HEC error." ::= { catsAal2PvcHistoryEntry 8 } catsAal2PvcCrcErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of egress AAL2 Type3 CPS PDUs dropped due to invalid CRC-10 error. CRC validation is for Type 3 packets only. Type 1 packets are not subjected to CRC-10 error validation. This does not count the Type 3 packets generated by the DSP." ::= { catsAal2PvcHistoryEntry 9 } catsAal2PvcInvOsfCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL2 cells dropped due to invalid OSF (OffSet Field) in the egress direction." ::= { catsAal2PvcHistoryEntry 10 } catsAal2PvcInvParCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL2 cells dropped due to invalid parity bit field in the egress direction." ::= { catsAal2PvcHistoryEntry 11 } catsAal2PvcCpsInvCidPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL2 CPS packets dropped in the egress direction due to invalid CID(Channel Identifier). The CID may be considered as invalid if it is out of range or not configured." ::= { catsAal2PvcHistoryEntry 12 } catsAal2PvcCpsInvUuiPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL2 CPS packets dropped in the egress direction due to invalid UUI field. " ::= { catsAal2PvcHistoryEntry 13 } catsAal2PvcCpsInvLenPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL2 CPS packets dropped in the egress direction due to invalid length field. " ::= { catsAal2PvcHistoryEntry 14 } catsAal5PvcHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CatsAal5PvcHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table represents a 24 hour history of statistics per AAL5 PVC. The statistics are collected using 15 minute intervals. Entries in this table are populated at the end of the interval." ::= { catsStatistics 3 } catsAal5PvcHistoryEntry OBJECT-TYPE SYNTAX CatsAal5PvcHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table. Each entry contains the statistics for a particular AAL5 PVC for the given 15 minute interval. The primary index, ifIndex, will be of ifType propAtm(197), atm(37) or aal5(49)." INDEX { ifIndex, catsAal5PvcVpi, catsAal5PvcVci, catsAal5PvcIntervalIndex } ::= { catsAal5PvcHistoryTable 1 } CatsAal5PvcHistoryEntry ::= SEQUENCE { catsAal5PvcVpi AtmVpIdentifier, catsAal5PvcVci AtmVcIdentifier, catsAal5PvcIntervalIndex Gauge, catsAal5PvcValidFlag TruthValue, catsAal5PvcDiscontinuityTime TimeStamp, catsAal5PvcPduSentPkts Counter, catsAal5PvcPduRcvdPkts Counter, catsAal5PvcInvCpiPdus Counter, catsAal5PvcOverSizedSDUs Counter, catsAal5PvcInvLenPdus Counter, catsAal5PvcCrc32ErrorPdus Counter, catsAal5PvcReassemTimerExpiryPdus Counter } catsAal5PvcVpi OBJECT-TYPE SYNTAX AtmVpIdentifier -- Rsyntax INTEGER(0..4095) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VPI value for the AAL5 PVC for which the statistics are being collected." ::= { catsAal5PvcHistoryEntry 1 } catsAal5PvcVci OBJECT-TYPE SYNTAX AtmVcIdentifier -- Rsyntax INTEGER(0..65535) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VCI value for the AAL5 PVC for which the statistics are being collected." ::= { catsAal5PvcHistoryEntry 2 } catsAal5PvcIntervalIndex OBJECT-TYPE SYNTAX Gauge(1..96) ACCESS not-accessible STATUS mandatory DESCRIPTION "This is the history interval number. The intervals are 15 minutes long and thus for a 24 hour period there will be 96 intervals. The 24 hour interval is aligned to wall clock. The index of 1 will represent the interval from 00:00 to 00:15. The index of 2 will represent the interval from 00:15 to 00:30 and so on." ::= { catsAal5PvcHistoryEntry 3 } catsAal5PvcValidFlag OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to indicate if the entry has valid statistics data. It contains a value of true(1) if the data is valid and false(2) otherwise. A possible scenario when this flag will be set to false(2) is when there are time changes due to daylight savings time and/ or time zone changes. This flag can also be set to false(2) if statistics in this 15 minute interval have experienced discontinuity." ::= { catsAal5PvcHistoryEntry 4 } catsAal5PvcDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object will represent the timestamp when the statistics in this 15 minute interval were discontinued due to a forced clear on the module. If this has the default value then it indicates that the statistics in this interval have not experienced any discontinuity." DEFVAL { 0 } ::= { catsAal5PvcHistoryEntry 5 } catsAal5PvcPduSentPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 PDUs transmitted to the network. This is applicable only to the PVCs configured as AAL5 PVCs (VoIP(Voice Over IP) PVCs or CCS PVCs in the case of VoAAL2 application)." ::= { catsAal5PvcHistoryEntry 6 } catsAal5PvcPduRcvdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 PDUs received from the network. This is applicable only to the PVCs configured as AAL5 PVCs (VoIP(Voice Over IP) PVCs or CCS(Common Channel Signaling) PVCs in the case of VoAAL2 application)." ::= { catsAal5PvcHistoryEntry 7 } catsAal5PvcInvCpiPdus OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 PDUs dropped in the egress direction due to invalid CPI(Common Part Indicator) field in the AAL5 PDU trailer. This is applicable only to the PVCs configured as AAL5 PVCs (VoIP(Voice Over IP) PVCs or CCS(Common Channel Signaling) PVCs in the case of VoAAL2 application)." ::= { catsAal5PvcHistoryEntry 8 } catsAal5PvcOverSizedSDUs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number AAL5 PDUs discarded on this AAL5 PVC at the interface associated with an AAL5 entity because the AAL5 SDUs were too large." ::= { catsAal5PvcHistoryEntry 9 } catsAal5PvcInvLenPdus OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 PDUs dropped due to length violations. This is applicable to CCS PVCs. The HDLC frames should have a minimum frame size in order for the proper interpretation by the upper layer protocol. " ::= { catsAal5PvcHistoryEntry 10 } catsAal5PvcCrc32ErrorPdus OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 PDUs dropped in the egress direction due to CRC-32 errors detected by the SAR. " ::= { catsAal5PvcHistoryEntry 11 } catsAal5PvcReassemTimerExpiryPdus OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of AAL5 PDU reassembly timer expirations. The timers are maintained in the egress direction for building an AAL5 PDU from the cells." ::= { catsAal5PvcHistoryEntry 12 } catsCidHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF CatsCidHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table represents a 24 hour history of statistics per CID. The statistics are collected using 15 minute intervals. The Channel IDentification (CID) is the standard term to identify an ATM AAL2 connection (ITU-T I.366.2). CID is unique within a VC (SVC or PVC). Entries in this table are populated at the end of the interval. " ::= { catsStatistics 4 } catsCidHistoryEntry OBJECT-TYPE SYNTAX CatsCidHistoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the table. Each entry contains the statistics for a particular CID for the given 15 minute interval. The primary index, ifIndex, will be of ifType propAtm(197), atm(37) or aal2(37)." INDEX { ifIndex, catsCidVpi, catsCidVci, catsCid, catsCidIntervalIndex } ::= { catsCidHistoryTable 1 } CatsCidHistoryEntry ::= SEQUENCE { catsCidVpi AtmVpIdentifier, catsCidVci AtmVcIdentifier, catsCid Gauge, catsCidIntervalIndex Gauge, catsCidValidFlag TruthValue, catsCidDiscontinuityTime TimeStamp, catsCidAvgSentPkts Counter, catsCidAvgRcvdPkts Counter, catsCidSentPkts Counter, catsCidRcvdPkts Counter, catsCidSentOctets Counter, catsCidRcvdOctets Counter, catsCidSentPeakPkts Counter, catsCidRcvdPeakPkts Counter, catsCidExtAISRcvdPkts Counter, catsCidExtRAIRcvdPkts Counter, catsCidExtConnAISRcvdPkts Counter, catsCidExtConnRDIRcvdPkts Counter, catsCidExtAISRcvCnts Counter, catsCidExtRAIRcvCnts Counter, catsCidExtConnAISCnts Counter, catsCidExtConnRDICnts Counter, catsCidExtAISXmtCnts Counter, catsCidExtRAIXmtCnts Counter } catsCidVpi OBJECT-TYPE SYNTAX AtmVpIdentifier -- Rsyntax INTEGER(0..4095) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VPI value of the ATM trunk connection with the CID for which the statistics are being collected." ::= { catsCidHistoryEntry 1 } catsCidVci OBJECT-TYPE SYNTAX AtmVcIdentifier -- Rsyntax INTEGER(0..65535) ACCESS not-accessible STATUS mandatory DESCRIPTION " The VCI value of the ATM trunk connection with the CID for which the statistics are being collected." ::= { catsCidHistoryEntry 2 } catsCid OBJECT-TYPE SYNTAX Gauge(1..2147483647) ACCESS not-accessible STATUS mandatory DESCRIPTION " This object is the CID of an ATM AAL2 connection for which the statistics are being collected." ::= { catsCidHistoryEntry 3 } catsCidIntervalIndex OBJECT-TYPE SYNTAX Gauge(1..96) ACCESS not-accessible STATUS mandatory DESCRIPTION "This is the history interval number. The intervals are 15 minutes long and thus for a 24 hour period there will be 96 intervals. The 24 hour interval is aligned to wall clock. The index of 1 will represent the interval from 00:00 to 00:15. The index of 2 will represent the interval from 00:15 to 00:30 and so on." ::= { catsCidHistoryEntry 4 } catsCidValidFlag OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to indicate if the entry has valid statistics data. It will take a value of true(1) if the data is valid and false(2) otherwise. A possible scenario when this flag will be set to false(2) is when there are time changes due to daylight savings time and/ or time zone changes. This flag can also be set to false(2) if statistics in this 15 minute interval have experienced discontinuity." ::= { catsCidHistoryEntry 5 } catsCidDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object will represent the timestamp when the statistics in this 15 minute interval were discontinued due to a forced clear on the module. If this has the default value then it indicates that the statistics in this interval have not experienced any discontinuity." DEFVAL { 0 } ::= { catsCidHistoryEntry 6 } catsCidAvgSentPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the average packets per second sent towards the network in this 15 minute interval. The average is computed by dividing the total number of packets sent over this 15 minute interval by the interval time (15 minutes). " ::= { catsCidHistoryEntry 7 } catsCidAvgRcvdPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the average packets per second received from the network in this 15 minute interval. The average is computed by dividing the total number of packets received over this 15 minute interval by the interval time (15 minutes)." ::= { catsCidHistoryEntry 8 } catsCidSentPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the count of packets sent towards the network in this 15 minute interval. " ::= { catsCidHistoryEntry 9 } catsCidRcvdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the count of packets received from the network in this 15 minute interval. " ::= { catsCidHistoryEntry 10 } catsCidSentOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the count of bytes sent towards the network in this 15 minute interval. " ::= { catsCidHistoryEntry 11 } catsCidRcvdOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the count of bytes received from the network in this 15 minute interval. " ::= { catsCidHistoryEntry 12 } catsCidSentPeakPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the peak packets per second sent towards the network in this 15 minute interval. The sent packets per second are monitored every second and the peak value over the 15 minute interval is returned in this object." ::= { catsCidHistoryEntry 13 } catsCidRcvdPeakPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets-per-sec ACCESS read-only STATUS mandatory DESCRIPTION "This attribute defines the peak packets per second received from the network in this 15 minute interval. The received packets per second are monitored every second and the peak value over the 15 minute interval is returned in this object." ::= { catsCidHistoryEntry 14 } catsCidExtAISRcvdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the number of external AIS AAL2 Type3 packets received in this 15 minute interval. " ::= { catsCidHistoryEntry 15 } catsCidExtRAIRcvdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the number of external RAI AAL2 Type3 packets received in this 15 minute interval. " ::= { catsCidHistoryEntry 16 } catsCidExtConnAISRcvdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the number of external connection AIS AAL2 Type2 packets received in this 15 minute interval. " ::= { catsCidHistoryEntry 17 } catsCidExtConnRDIRcvdPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the number of External Connection RDI (Remote Defect Ind.) AAL2 Type2 packets received in this 15 minute interval. " ::= { catsCidHistoryEntry 18 } catsCidExtAISRcvCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the count of external AIS AAL2 Type3 packets received in this 15 minute interval. " ::= { catsCidHistoryEntry 19 } catsCidExtRAIRcvCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the number of external RAI AAL2 Type3 packets received in this 15 minute interval." ::= { catsCidHistoryEntry 20 } catsCidExtConnAISCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains count of external connection AIS AAL2 Type2 packets received in this 15 minute interval. " ::= { catsCidHistoryEntry 21 } catsCidExtConnRDICnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the count of external connection RDI (Remote Defect Ind.) AAL2 Type2 packets received in this 15 minute interval. " ::= { catsCidHistoryEntry 22 } catsCidExtAISXmtCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the count of external AIS AAL2 Type3 packets transmitted in this 15 minute interval. " ::= { catsCidHistoryEntry 23 } catsCidExtRAIXmtCnts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "This object contains the count of external RAI AAL2 Type3 packets transmitted in this 15 minute interval. " ::= { catsCidHistoryEntry 24 } catsPvcStatGroup OBJECT IDENTIFIER ::= { catsMIBGroups 1 } -- OBJECT-GROUP -- Status -- deprecated -- Descr -- A collection of objects used for maintaining history -- statistics per PVC. -- objects -- catsPvcValidFlag, catsPvcDiscontinuityTime, -- catsPvcAtmXmtCells, catsPvcAtmRcvCells, catsPvcAvgAtmXmtCells, -- catsPvcAvgAtmRcvCells, catsPvcPeakAtmXmtCells, -- catsPvcPeakAtmRcvCells, catsPvcOamXmtEndLpbkCells, -- catsPvcOamRcvEndLpbkCells, catsPvcOamXmtSegLpbkCells, -- catsPvcOamRcvSegLpbkCells, catsPvcOamLpbkLostCells, -- catsPvcDiscardedRcvOamCells, catsPvcAisSuppressCnts, -- catsPvcXmtAisCnts, catsPvcRcvAisCnts, catsPvcXmtFerfCnts, -- catsPvcRcvFerfCnts, catsPvcXmtAisCells, catsPvcRcvAisCells, -- catsPvcXmtFerfCells, catsPvcRcvFerfCells catsAal2PvcStatGroup OBJECT IDENTIFIER ::= { catsMIBGroups 2 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects used for maintaining history -- statistics per AAL2 PVC. -- objects -- catsAal2PvcValidFlag, catsAal2PvcDiscontinuityTime, -- catsAal2PvcCpsSentPkts, catsAal2PvcCpsRcvdPkts, -- catsAal2PvcHecErrors, catsAal2PvcCrcErrors, -- catsAal2PvcInvOsfCells, catsAal2PvcInvParCells, -- catsAal2PvcCpsInvCidPkts, catsAal2PvcCpsInvUuiPkts, -- catsAal2PvcCpsInvLenPkts catsAal5PvcStatGroup OBJECT IDENTIFIER ::= { catsMIBGroups 3 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects used for maintaining history -- statistics per AAL5 PVC. -- objects -- catsAal5PvcValidFlag, catsAal5PvcDiscontinuityTime, -- catsAal5PvcPduSentPkts, catsAal5PvcPduRcvdPkts, -- catsAal5PvcInvCpiPdus, catsAal5PvcOverSizedSDUs, -- catsAal5PvcInvLenPdus, catsAal5PvcCrc32ErrorPdus, -- catsAal5PvcReassemTimerExpiryPdus catsCidHistoryStatGroup OBJECT IDENTIFIER ::= { catsMIBGroups 4 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects used for maintaining history -- statistics per CID. -- objects -- catsCidValidFlag, catsCidDiscontinuityTime, -- catsCidAvgSentPkts, catsCidAvgRcvdPkts, catsCidSentPkts, -- catsCidRcvdPkts, catsCidSentOctets, catsCidRcvdOctets, -- catsCidSentPeakPkts, catsCidRcvdPeakPkts, -- catsCidExtAISRcvdPkts, catsCidExtRAIRcvdPkts, -- catsCidExtConnAISRcvdPkts, catsCidExtConnRDIRcvdPkts, -- catsCidExtAISRcvCnts, catsCidExtRAIRcvCnts, -- catsCidExtConnAISCnts, catsCidExtConnRDICnts, -- catsCidExtAISXmtCnts, catsCidExtRAIXmtCnts catsPvcStatGroupRev1 OBJECT IDENTIFIER ::= { catsMIBGroups 5 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects used for maintaining history -- statistics per PVC. -- objects -- catsPvcValidFlag, catsPvcDiscontinuityTime, -- catsPvcAtmXmtCells, catsPvcAtmRcvCells, catsPvcAvgAtmXmtCells, -- catsPvcAvgAtmRcvCells, catsPvcPeakAtmXmtCells, -- catsPvcPeakAtmRcvCells, catsPvcOamXmtEndLpbkCells, -- catsPvcOamRcvEndLpbkCells, catsPvcOamXmtSegLpbkCells, -- catsPvcOamRcvSegLpbkCells, catsPvcOamLpbkLostCells, -- catsPvcDiscardedRcvOamCells, catsPvcAisSuppressCnts, -- catsPvcXmtAisCnts, catsPvcRcvAisCnts, catsPvcXmtFerfCnts, -- catsPvcRcvFerfCnts, catsPvcXmtAisCells, catsPvcRcvAisCells, -- catsPvcXmtFerfCells, catsPvcRcvFerfCells, -- catsPvcOamLpbkTimeoutCnts, catsPvcNewOamLpbkTimeoutDur, -- catsPvcActiveOamLpbkTimeoutDur, -- catsPvcOamLpbkTimeoutThreshold ciscoAtmPvcStatMIBCompliance OBJECT IDENTIFIER ::= { catsMIBCompliances 1 } -- MODULE-COMPLIANCE -- Status -- deprecated -- Descr -- Compliance statement for CISCO-ATM-TRUNK-STAT-MIB. -- Module -- >>current<< -- MandGroup -- catsPvcStatGroup -- MandGroup -- catsAal2PvcStatGroup -- MandGroup -- catsAal5PvcStatGroup -- MandGroup -- catsCidHistoryStatGroup ciscoAtmPvcStatMIBComplianceRev1 OBJECT IDENTIFIER ::= { catsMIBCompliances 2 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- Compliance statement for CISCO-ATM-TRUNK-STAT-MIB. -- Module -- >>current<< -- MandGroup -- catsPvcStatGroupRev1 -- MandGroup -- catsAal2PvcStatGroup -- MandGroup -- catsAal5PvcStatGroup -- MandGroup -- catsCidHistoryStatGroup END