-- MIB file created 26-Jan-2006 15:28:44, by
--   SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com

CISCO-C8500-REDUNDANCY-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-C8500-REDUNDANCY-MIB.my"
-- Compile options "4 7 F H N O W 03 06 0B 0G 0N 0T"

IMPORTS
    TimeStamp, TruthValue
            FROM SNMPv2-TC-v1
    ciscoMgmt
            FROM CISCO-SMI
    Gauge
            FROM RFC1155-SMI
    OBJECT-TYPE
            FROM RFC-1212
    TRAP-TYPE
            FROM RFC-1215;

ciscoC8500RedundancyMIB OBJECT IDENTIFIER ::= { ciscoMgmt 105 }
-- MODULE-IDENTITY
--  LastUpdated
--    200305040000Z
--  OrgName
--    Cisco Systems, Inc.
--  ContactInfo
--            Cisco Systems
--             Customer Service
--    
--    Postal:  170 W. Tasman Drive
--             San Jose, CA  95134
--             USA
--    
--    Tel: +1 800 553-NETS
--    
--    E-mail:  cs-atm@cisco.com
--  Descr
--    This MIB allows management of redundancy of CPU and 
--     switch cards for the Catalyst 8540 switch, and other 
--     products with similar implementations.
--    
--     The Catalyst 8540 is an ATM switch. It has 13 (or, in
--     some models, 14) slots, of which 2 slots can hold CPU
--     cards, and 3 (or, in some models, 4) slots can hold
--     switch cards. A switch card is one that contains the
--     ATM switching fabric. Two switch cards are combined 
--     to operate in 20Gbps switching mode.
--     For CPU cards, 1+1 redundancy is supported.
--     For switch cards, 2+1 redundancy is supported.
--  RevDate
--    200305040000Z
--  RevDescr
--    Added the following scalar objects to ccrCpu group:
--     ccrCpuStandbyEnableMode, ccrCpuSwitchoverTime,
--     ccrForceCounterSync, ccrIfCounterSyncFreq,
--     ccrVcCounterSyncFreq, ccrSigCounterSyncEnable.
--  RevDate
--    199806220000Z
--  RevDescr
--    Initial version of the MIB Module.

ciscoC8500RedundancyMIBObjects OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIB 1 }
ccrCpu          OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBObjects 1 }
ccrSwitch       OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBObjects 2 }
ciscoC8500RedundancyMIBNotificationPrefix OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIB 2 }
ccrMIBNotifications OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBNotificationPrefix 0 }
ciscoC8500RedundancyMIBConformance OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIB 3 }
ciscoC8500RedundancyMIBCompliances OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBConformance 1 }
ciscoC8500RedundancyMIBGroups OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBConformance 2 }

RedundancyStatus ::= INTEGER {
        notPresent(1),
        ok(2),
        fault(3)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    The operational status of a card.

RedundancyMode ::= INTEGER {
        active(1),
        standby(2),
        unused(3),
        notPresent(4)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    The redundancy mode of a card.
--    
--    The redundancy mode of a card is part of the state of
--    the redundancy machine (i.e., the hardware or software
--    that implements redundancy). The redundancy modes of
--    all the cards in a redundancy group together represent
--    the state of the redundancy machine for that
--    redundancy group. The inputs to the redundancy machine
--    that cause the redundancy mode of a card to transition
--    from one value to another are events like card
--    failure, card removal, user configuration, etc.
--    Objects defined using this TC have a MAX-ACCESS of
--    read-write or read-create. This allows a user to force
--    the redundancy machine to transition to a desired 
--    state.
--    
--    The following values may be written:
--    
--      active(1) - Make this card an active member of the
--    redundancy group.
--    
--      standby(2) - Make this card a standby member of
--    the redundancy group.
--    
--      unused(3)  - Do not use this card.
--    
--    Writing the above values may cause a switchover.
--    
--    When read, the values mean:
--    
--     active(1) - This card is an active member of the
--    redundancy group.
--    
--     standby(2) - This card is a standby member of the
--    redundancy group.
--    
--     unused(3) - This card is not being used at present.
--    
--     notPresent(4) - There is no card in the slot.

RedundancySlotIndex ::= Gauge(1..65535)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A value that identifies a physical slot in the 
--     chassis.
--    
--     For a chassis with slots that are numbered left to 
--     right, the leftmost slot has value 1.
--    
--     For a chassis with slots that are numbered top to 
--     bottom, the topmost slot has value 1.

ccrCpuTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CcrCpuEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "There is an entry in this table for each slot that
         can hold a CPU card."
    ::= { ccrCpu 1 }

ccrCpuEntry OBJECT-TYPE
    SYNTAX CcrCpuEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Redundancy information for a CPU card."
    INDEX { ccrCpuSlotIndex }
    ::= { ccrCpuTable 1 }

CcrCpuEntry ::= SEQUENCE {
    ccrCpuSlotIndex RedundancySlotIndex,
    ccrCpuMode RedundancyMode,
    ccrCpuStatus RedundancyStatus
    }

ccrCpuSlotIndex OBJECT-TYPE
    SYNTAX RedundancySlotIndex
--    Rsyntax Gauge(1..65535)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Identifies a chassis slot."
    ::= { ccrCpuEntry 1 }

ccrCpuMode OBJECT-TYPE
    SYNTAX RedundancyMode
--    Rsyntax INTEGER {
--        active(1),
--        standby(2),
--        unused(3),
--        notPresent(4)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The redundancy mode of this CPU card."
    ::= { ccrCpuEntry 2 }

ccrCpuStatus OBJECT-TYPE
    SYNTAX RedundancyStatus
--    Rsyntax INTEGER {
--        notPresent(1),
--        ok(2),
--        fault(3)
--        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The operational status of this CPU card."
    ::= { ccrCpuEntry 3 }

ccrSyncConfigOnSet OBJECT-TYPE
    SYNTAX OCTET STRING(SIZE(1..2))
        -- BITS are:
        --   runningConfig(0)
        --   startupConfig(1)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The device's running-configuration and
        startup-configuration both reside on the active CPU
        card.  This object indicates whether these
        configurations should be copied from the active CPU
        to the standby CPU whenever they change.  It is
        acceptable to copy either, both, or neither."
    ::= { ccrCpu 2 }

ccrCpuStandbyEnableMode OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object is used to allow or disallow the
         execution of the enable exec command on the 
         secondary CPU.
         
         When set to 'true', the enable exec command can be 
         executed on secondary CPU, and the user may enter 
         enable mode after keying in the password configured.
         When set to 'false', the enable exec command cannot 
         be executed; thus, no user may enter enabled mode."
    DEFVAL { false }
    ::= { ccrCpu 3 }

ccrCpuSwitchoverTime OBJECT-TYPE
    SYNTAX INTEGER(0..65535)
--  Units
--    seconds
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The time taken for the most recent CPU switchover."
    ::= { ccrCpu 4 }

ccrForceCounterSync OBJECT-TYPE
    SYNTAX INTEGER {
        forcesync(1),
        noop(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object is used to force the synchronization of
         counters from primary CPU to secondary CPU. It should
         generally be set just before a controlled Route 
         Processor Switchover.
        
         When this object is retrieved, the value 'noop' is 
         returned.   When this object is set to 'noop' no 
         operation is performed."
    ::= { ccrCpu 5 }

ccrIfCounterSyncFreq OBJECT-TYPE
    SYNTAX INTEGER(0..1440)
--  Units
--    minutes
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object configures the periodicity of interface
         counter synchronization from primary CPU to 
         secondary CPU. Setting this object to 0 will disable 
         counter synchronization."
    ::= { ccrCpu 6 }

ccrVcCounterSyncFreq OBJECT-TYPE
    SYNTAX INTEGER(0..1440)
--  Units
--    minutes
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object configures the periodicity of Virtual 
         Circuit (VC) counter synchronization from primary CPU
         to secondary CPU.  Setting this object to 0 will 
         disable counter synchronization."
    ::= { ccrCpu 7 }

ccrSigCounterSyncEnable OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object configures the synchronization of ATM
         Signalling Statistics from primary CPU to 
         secondary CPU.
        
         When this object is set to 'true', sychronization 
         is enabled.  When this object is set to 'false', 
         synchronization is disabled."
    ::= { ccrCpu 8 }

ccrSwitchTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CcrSwitchEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "There is an entry in this table for each slot that
         can hold a switch card. A 'switch card' is a card that
         contains the ATM switch fabric."
    ::= { ccrSwitch 1 }

ccrSwitchEntry OBJECT-TYPE
    SYNTAX CcrSwitchEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Redundancy information for a switch card."
    INDEX { ccrSwitchSlotIndex }
    ::= { ccrSwitchTable 1 }

CcrSwitchEntry ::= SEQUENCE {
    ccrSwitchSlotIndex RedundancySlotIndex,
    ccrSwitchMode RedundancyMode,
    ccrSwitchStatus RedundancyStatus
    }

ccrSwitchSlotIndex OBJECT-TYPE
    SYNTAX RedundancySlotIndex
--    Rsyntax Gauge(1..65535)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Identifies a chassis slot."
    ::= { ccrSwitchEntry 1 }

ccrSwitchMode OBJECT-TYPE
    SYNTAX RedundancyMode
--    Rsyntax INTEGER {
--        active(1),
--        standby(2),
--        unused(3),
--        notPresent(4)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The redundancy mode of this switch card."
    ::= { ccrSwitchEntry 2 }

ccrSwitchStatus OBJECT-TYPE
    SYNTAX RedundancyStatus
--    Rsyntax INTEGER {
--        notPresent(1),
--        ok(2),
--        fault(3)
--        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The operational status of this switch card."
    ::= { ccrSwitchEntry 3 }

ccrSwitchLastSwitchoverTime OBJECT-TYPE
    SYNTAX TimeStamp
--    Rsyntax TimeTicks
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The value of sysUpTime at the last switchover of the 
         switch cards. 
        
         The value is zero if there was no switchover since
         agent initialization."
    ::= { ccrSwitch 2 }

ccrSwitchLastSwitchoverReason OBJECT-TYPE
    SYNTAX INTEGER {
        none(1),
        notKnown(2),
        userInitiated(3),
        cardFailed(4),
        cardRecovered(5),
        cardRemoved(6),
        cardInserted(7)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The reason for the last switch card switchover.
        
         The value is none(1) if there was no switchover since
         agent initialization."
    ::= { ccrSwitch 3 }

ccrSwitchBw OBJECT-TYPE
    SYNTAX INTEGER {
        tenGbps(1),
        twentyGbps(2)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The switching capacity (i.e., bandwidth) of the
         switch fabric.
            tenGbps(1) - 10 Gigabits/sec
            twentyGbps(2) - 20 Gigabits/sec."
    ::= { ccrSwitch 4 }

ccrDesiredSwitchBw OBJECT-TYPE
    SYNTAX INTEGER {
        tenGbps(1),
        twentyGbps(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The desired switching capacity (i.e., bandwidth) of 
         the switch fabric.
            tenGbps(1) - 10 Gigabits/sec
            twentyGbps(2) - 20 Gigabits/sec
        
         If the value configured by writing to this object is
         supported by the device, it will be applied at the 
         next reboot. The speed at which the switch fabric is
         currently operating is reflected by the value of 
         ccrSwitchBw."
    ::= { ccrSwitch 5 }

ccrCpuStatusChange TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE ciscoC8500RedundancyMIBNotificationPrefix
    VARIABLES {
        ccrCpuStatus }
--  Status
--    mandatory
    DESCRIPTION
        "This notification is generated when the value of
         ccrCpuStatus changes for a CPU card.
        
         The varbind indicates the current status of the
         affected card."
    ::= 1

ccrSwitchStatusChange TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE ciscoC8500RedundancyMIBNotificationPrefix
    VARIABLES {
        ccrSwitchStatus }
--  Status
--    mandatory
    DESCRIPTION
        "This notification is generated when the value of
         ccrSwitchStatus changes for a switch card.
        
         The varbind indicates the current status of the
         affected card."
    ::= 2

ccrSwitchModeChange TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE ciscoC8500RedundancyMIBNotificationPrefix
    VARIABLES {
        ccrSwitchMode }
--  Status
--    mandatory
    DESCRIPTION
        "This notification is generated when the value of
         ccrSwitchMode changes from active(1) to either
         standby(2) or unused(3) or notPresent(4).
         The varbind indicates the current mode of the 
         affected card."
    ::= 3

ccrCpuMibGroup OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBGroups 1 }
-- OBJECT-GROUP
--  Status
--    obsolete
--  Descr
--    A collection of objects providing the ability to
--     manage CPU card redundancy.
--  objects
--    ccrCpuMode, ccrCpuStatus, ccrSyncConfigOnSet

ccrSwitchMibGroup OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBGroups 2 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing the ability to
--     manage Switch Fabric card redundancy.
--  objects
--    ccrSwitchMode, ccrSwitchStatus, ccrSwitchLastSwitchoverTime, 
--    ccrSwitchLastSwitchoverReason, ccrSwitchBw, 
--    ccrDesiredSwitchBw

ccrCpuMibGroup1 OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBGroups 4 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing the ability to
--    manage CPU card redundancy and redundancy feature
--    for counter, enable password on secondary and
--    switchover duration.
--  objects
--    ccrCpuMode, ccrCpuStatus, ccrSyncConfigOnSet, 
--    ccrCpuStandbyEnableMode, ccrCpuSwitchoverTime, 
--    ccrForceCounterSync, ccrIfCounterSyncFreq, 
--    ccrVcCounterSyncFreq, ccrSigCounterSyncEnable

ccrNotificationsGroup OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBGroups 3 }
-- NOTIFICATION-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of notifications related to redundancy.
--  notifications
--    ccrCpuStatusChange, ccrSwitchStatusChange, 
--    ccrSwitchModeChange

ciscoC8500RedundancyMIBCompliance OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    obsolete
--  Descr
--    The compliance statement for Cisco agents which 
--     implement the CISCO-C8500-REDUNDANCY-MIB.
--  Module
--    >>current<<
--   MandGroup
--    ccrCpuMibGroup
--   MandGroup
--    ccrSwitchMibGroup

ciscoC8500RedundancyMIBComplianceRev1 OBJECT IDENTIFIER ::= { ciscoC8500RedundancyMIBCompliances 2 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--    The compliance statement to include objects
--     related to the redundancy features like
--     enable password on secondary, switchover
--     duration and counter.
--  Module
--    >>current<<
--   MandGroup
--    ccrCpuMibGroup1
--   MandGroup
--    ccrSwitchMibGroup
--   MandGroup
--    ccrNotificationsGroup


END