-- MIB file created 15-Sep-2003 14:10:26, by -- SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com CISCO-FRAME-RELAY-MIB DEFINITIONS ::= BEGIN -- From file: "CISCO-FRAME-RELAY-MIB.my" -- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T" IMPORTS DisplayString, TruthValue FROM SNMPv2-TC-v1 ciscoMgmt FROM CISCO-SMI InterfaceIndex FROM IF-MIB ifIndex FROM RFC1213-MIB frDlcmiIfIndex, frCircuitIfIndex, frCircuitDlci FROM RFC1315-MIB Counter, IpAddress FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212; ciscoFrameRelayMIB OBJECT IDENTIFIER ::= { ciscoMgmt 49 } -- MODULE-IDENTITY -- LastUpdated -- 200010130000Z -- OrgName -- Cisco Systems, Inc. -- ContactInfo -- Cisco Systems -- Customer Service -- -- Postal: 170 W Tasman Drive -- San Jose, CA 95134 -- USA -- -- Tel: +1 800 553-NETS -- -- E-mail: cs-framerelay@cisco.com -- Descr -- Cisco Frame Relay MIB -- RevDate -- 200010130000Z -- RevDescr -- (1) Added objects of FR Switching, FR Fragmentation -- and FR/ATM Interworking. -- (2) Objects for per PVC I/O rate is added to -- cfrExtCircuitTable -- RevDate -- 200005220000Z -- RevDescr -- (1) Added ELMI subgroup for ELMI objects. -- RevDate -- 200005160000Z -- RevDescr -- (1) Added Traffic Shaping parameter objects to -- cfrExtCircuitTable. -- (2) Deprecated cfrSvcMinThruputOut and -- cfrSvcMinThruputIn. Added cfrExtCircuitMinThruputOut -- and cfrExtCircuitMinThruputIn in cfrExtCircuitTable -- inorder to make them applicable to both PVC/SVC. -- (3) Added cfrExtCircuitBandwidth object to -- cfrExtCircuitTable. -- RevDate -- 200004260000Z -- RevDescr -- (1) add an integer value for cfrMapPayloadCompressType; -- (2) reword the Description statements for -- { cfrMapPayloadCompressType, -- cfrExtCircuitUncompressIns, -- cfrExtCircuitUncompressOuts } -- so that they are not limited to software compression. -- RevDate -- 9908210000Z -- RevDescr -- (1) Added cfrExtCircuitUncompressOuts and -- cfrExtCircuitUncompressIns to the circuit subgroup; -- (2) Added cfrMapRtpHdrCompress and cfrMapPayloadCompressType -- to the mapping subgroup; -- (3) cfrMapPayloadCompress becomes deprecated, obsoleted -- by cfrMapPayloadCompressType; -- (4) frCircuitSentOctets and frCircuitReceivedOctets -- per RFC1315 will reflect the number of bytes in Frame Relay -- frames sent to and received from the physical layer. Same -- effect is applied to ifOutOctets and ifInOctets as well -- when ifIndex refers to a Frame Relay subinterface. -- RevDate -- 9608150000Z -- RevDescr -- Initial version of this MIB module. ciscoFrMIBObjects OBJECT IDENTIFIER ::= { ciscoFrameRelayMIB 1 } cfrLmiObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 1 } cfrCircuitObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 2 } cfrMapObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 3 } cfrSvcObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 4 } cfrElmiObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 5 } cfrFragObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 6 } cfrConnectionObjs OBJECT IDENTIFIER ::= { ciscoFrMIBObjects 7 } ciscoFrMIBConformance OBJECT IDENTIFIER ::= { ciscoFrameRelayMIB 3 } ciscoFrMIBCompliances OBJECT IDENTIFIER ::= { ciscoFrMIBConformance 1 } ciscoFrMIBGroups OBJECT IDENTIFIER ::= { ciscoFrMIBConformance 2 } DlciNumber ::= INTEGER(0..1023) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Numerical format of Data Link Connection Identifier -- (DLCI) in decimal, identical to the 'DLCI' as INTEGER -- of 0..DLCINumber in RFC1315. The maximum value depends -- on Frame Relay implementation, which is currently set -- to be 1023 for 2-octet address format per UNI -- Implementation Agreement FRF.1. CfrMapProtocols ::= INTEGER { arp(1), serialArp(6), ip(7), xns(10), novell(11), apollo(12), vines(13), appletalk(16), ieeeSpanning(18), decnet(22), clns(25), rsrb(37), bridge(38), stun(39), frArp(40), uncompressedTcp(47), compressedTcp(48), llc2(49), frSwitch(53), dlsw(63), nhrp(74), compressedRtp(83), wildcard(999) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Cisco link types (network protocols) that run -- over Frame Relay. Associated values, except for -- wildcard, match assigned values of internal software -- respectively. cfrLmiTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrLmiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of Frame Relay LMI information that are either supplemental to the frDlcmiTable of RFC 1315 or specific to Cisco's implementation." REFERENCE "American National Standard T1.617-1991, Annex D" ::= { cfrLmiObjs 1 } cfrLmiEntry OBJECT-TYPE SYNTAX CfrLmiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains information of Frame Relay LMI over one physical interface. They are mostly FR generic and some Cisco specific." INDEX { frDlcmiIfIndex } -- Augments frDlcmiEntry FROM RFC1315-MIB ::= { cfrLmiTable 1 } CfrLmiEntry ::= SEQUENCE { cfrLmiLinkstatus INTEGER, cfrLmiLinkType INTEGER, cfrLmiEnquiryIns Counter, cfrLmiEnquiryOuts Counter, cfrLmiStatusIns Counter, cfrLmiStatusOuts Counter, cfrLmiUpdateStatusIns Counter, cfrLmiUpdateStatusOuts Counter, cfrLmiStatusTimeouts Counter, cfrLmiStatusEnqTimeouts Counter, cfrLmiN392Dce INTEGER, cfrLmiN393Dce INTEGER, cfrLmiT392Dce INTEGER } cfrLmiLinkstatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Data link status via LMI." ::= { cfrLmiEntry 1 } cfrLmiLinkType OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2), nni(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Frame Relay link type." ::= { cfrLmiEntry 2 } cfrLmiEnquiryIns OBJECT-TYPE SYNTAX Counter -- Units -- messages ACCESS read-only STATUS mandatory DESCRIPTION "Number of Status Enquiry messages received." ::= { cfrLmiEntry 3 } cfrLmiEnquiryOuts OBJECT-TYPE SYNTAX Counter -- Units -- messages ACCESS read-only STATUS mandatory DESCRIPTION "Number of Status Enquiry messages sent." ::= { cfrLmiEntry 4 } cfrLmiStatusIns OBJECT-TYPE SYNTAX Counter -- Units -- messages ACCESS read-only STATUS mandatory DESCRIPTION "Number of Status messages received." ::= { cfrLmiEntry 5 } cfrLmiStatusOuts OBJECT-TYPE SYNTAX Counter -- Units -- messages ACCESS read-only STATUS mandatory DESCRIPTION "Number of Status messages sent." ::= { cfrLmiEntry 6 } cfrLmiUpdateStatusIns OBJECT-TYPE SYNTAX Counter -- Units -- messages ACCESS read-only STATUS mandatory DESCRIPTION "Number of Update Status messages received." ::= { cfrLmiEntry 7 } cfrLmiUpdateStatusOuts OBJECT-TYPE SYNTAX Counter -- Units -- messages ACCESS read-only STATUS mandatory DESCRIPTION "Number of Update Status messages sent" ::= { cfrLmiEntry 8 } cfrLmiStatusTimeouts OBJECT-TYPE SYNTAX Counter -- Units -- times ACCESS read-only STATUS mandatory DESCRIPTION "Number of times when timeout occurred on waiting for Status message" ::= { cfrLmiEntry 9 } cfrLmiStatusEnqTimeouts OBJECT-TYPE SYNTAX Counter -- Units -- times ACCESS read-only STATUS mandatory DESCRIPTION "Number of times when timeout occurred on waiting for Status Enquiry message" ::= { cfrLmiEntry 10 } cfrLmiN392Dce OBJECT-TYPE SYNTAX INTEGER(0..10) ACCESS read-only STATUS mandatory DESCRIPTION "LMI error threshold for DCE interface. For DTE, value becomes 0." ::= { cfrLmiEntry 11 } cfrLmiN393Dce OBJECT-TYPE SYNTAX INTEGER(0..10) ACCESS read-only STATUS mandatory DESCRIPTION "LMI monitored event count for DCE interface. For DTE, value becomes zero (0)." ::= { cfrLmiEntry 12 } cfrLmiT392Dce OBJECT-TYPE SYNTAX INTEGER(0..30) -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "DCE polling verification timer for DCE interface For DTE, the value becomes zero (0)." ::= { cfrLmiEntry 13 } cfrCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of descriptive and statistics information that are generic to Frame Relay virtual circuits." ::= { cfrCircuitObjs 1 } cfrCircuitEntry OBJECT-TYPE SYNTAX CfrCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains information of a circuit that are not included in frCircuitTable of RFC1315 but are generic to Frame Relay." INDEX { frCircuitIfIndex, frCircuitDlci } -- Augments frCircuitEntry FROM RFC1315-MIB ::= { cfrCircuitTable 1 } CfrCircuitEntry ::= SEQUENCE { cfrCircuitDEins Counter, cfrCircuitDEouts Counter, cfrCircuitDropPktsOuts Counter, cfrCircuitType INTEGER } cfrCircuitDEins OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of packets received with the Discarded Eligibility indictor (the DE bit) set." ::= { cfrCircuitEntry 1 } cfrCircuitDEouts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of packets transmitted with DE bit set." ::= { cfrCircuitEntry 2 } cfrCircuitDropPktsOuts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of discarded packets that were to be sent." ::= { cfrCircuitEntry 3 } cfrCircuitType OBJECT-TYPE SYNTAX INTEGER { pvc(1), svc(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Basic circuit type" ::= { cfrCircuitEntry 4 } cfrExtCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrExtCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of Cisco implementation specific FR circuit information. This is a Cisco extension for the frCircuitTable of RFC 1315." ::= { cfrCircuitObjs 2 } cfrExtCircuitEntry OBJECT-TYPE SYNTAX CfrExtCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains information of a Frame Relay virtual circuit that are specific to Cisco implementation." INDEX { frCircuitIfIndex, frCircuitDlci } -- Augments frCircuitEntry FROM RFC1315-MIB ::= { cfrExtCircuitTable 1 } CfrExtCircuitEntry ::= SEQUENCE { cfrExtCircuitIfName DisplayString, cfrExtCircuitIfType INTEGER, cfrExtCircuitSubifIndex InterfaceIndex, cfrExtCircuitMapStatus INTEGER, cfrExtCircuitCreateType INTEGER, cfrExtCircuitMulticast TruthValue, cfrExtCircuitRoutedDlci DlciNumber, cfrExtCircuitRoutedIf InterfaceIndex, cfrExtCircuitUncompressIns Counter, cfrExtCircuitUncompressOuts Counter, cfrExtCircuitFECNOuts Counter, cfrExtCircuitBECNOuts Counter, cfrExtCircuitMinThruputOut INTEGER, cfrExtCircuitMinThruputIn INTEGER, cfrExtCircuitBcastPktOuts Counter, cfrExtCircuitBcastByteOuts Counter, cfrExtCircuitBandwidth INTEGER, cfrExtCircuitShapeByteLimit INTEGER, cfrExtCircuitShapeInterval INTEGER, cfrExtCircuitShapeByteIncrement INTEGER, cfrExtCircuitShapePkts Counter, cfrExtCircuitShapeBytes Counter, cfrExtCircuitShapePktsDelay Counter, cfrExtCircuitShapeBytesDelay Counter, cfrExtCircuitShapeActive TruthValue, cfrExtCircuitShapeAdapting INTEGER, cfrExtCircuitTxDataRate INTEGER, cfrExtCircuitTxPktRate INTEGER, cfrExtCircuitRcvDataRate INTEGER, cfrExtCircuitRcvPktRate INTEGER } cfrExtCircuitIfName OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "The textual name of the main interface or the subinterface that this DLCI is associated with. This is the same name string of an interface used in the configuration and all console displays, such as 'serial 0', 'serial 3/0.3', etc." ::= { cfrExtCircuitEntry 1 } cfrExtCircuitIfType OBJECT-TYPE SYNTAX INTEGER { mainInterface(1), pointToPoint(2), multipoint(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of the subinterface this DLCI is associated with, if configured." ::= { cfrExtCircuitEntry 2 } cfrExtCircuitSubifIndex OBJECT-TYPE SYNTAX InterfaceIndex -- Rsyntax INTEGER(1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "For value greater than zero (0), it indicates the network management interface index for the subinterface associated with this DLCI. Value 0 means the DLCI is not associated with any subinterface." ::= { cfrExtCircuitEntry 3 } cfrExtCircuitMapStatus OBJECT-TYPE SYNTAX INTEGER(0..2047) ACCESS read-only STATUS mandatory DESCRIPTION "The mapping protocols (internally considered as the 'link type') applied on this circuit. The value ranges from 0 to 2047. For point-to-point DLCI, the value stays zero. Otherwise, the value is a sum. It initially takes the value zero, then, for each type of Protocol, 2 raised to a power is added to the sum. The following table presents respective power and equivalent value for each applicable type: Protocol Power Value -------- ----- ----- IP 0 1 IPX 1 2 Appletalk 2 4 XNS 3 8 VINES 4 16 DECnet 5 32 CLNS 6 64 Bridging 7 128 RSRB 8 256 STUN 9 512 LLC2 10 1024 For example, value 3 means the circuit's mapping protocols include IP and IPX. (3 = 2**1 + 2**0, where 0 corresponds to IP and 1 to IPX.) Value 0 means there is currently no mapping protocol for the circuit. See cfrMapTable for more mapping information." ::= { cfrExtCircuitEntry 4 } cfrExtCircuitCreateType OBJECT-TYPE SYNTAX INTEGER { dynamic(1), static(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Identify the last source of the circuit's creation." ::= { cfrExtCircuitEntry 5 } cfrExtCircuitMulticast OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "Indicate if this DLCI is a multicast DLCI." ::= { cfrExtCircuitEntry 6 } cfrExtCircuitRoutedDlci OBJECT-TYPE SYNTAX DlciNumber -- Rsyntax INTEGER(0..1023) ACCESS read-only STATUS mandatory DESCRIPTION "The routed DLCI to pair up with this DLCI for switching function. NOTE: Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI." ::= { cfrExtCircuitEntry 7 } cfrExtCircuitRoutedIf OBJECT-TYPE SYNTAX InterfaceIndex -- Rsyntax INTEGER(1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The interface for the routed DLCI that pairs up with this DLCI for switching. Value greater than 0 is the InterfaceIndex for that interface. Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI." ::= { cfrExtCircuitEntry 8 } cfrExtCircuitUncompressIns OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Number of inbound octets of the data packets, accounted at Frame Relay level after FRF.9 payload decompression is applied. In the case of non-FRF.9, this value could be identical to frCircuitReceivedOctets, unless otherwise noted." ::= { cfrExtCircuitEntry 9 } cfrExtCircuitUncompressOuts OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Number of outbound octets of the data packets, accounted at Frame Relay level before FRF.9 payload compression is applied. In the case of non-FRF.9, this value could be identical to frCircuitSentOctets, unless otherwise noted." ::= { cfrExtCircuitEntry 10 } cfrExtCircuitFECNOuts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames sent out to the network indicating forward congestion." ::= { cfrExtCircuitEntry 11 } cfrExtCircuitBECNOuts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames sent out to the network indicating backward congestion." ::= { cfrExtCircuitEntry 12 } cfrExtCircuitMinThruputOut OBJECT-TYPE SYNTAX INTEGER(9600..1544000) -- Units -- bits per second ACCESS read-only STATUS mandatory DESCRIPTION "Circuit's outgoing minimal Throughput based on configuration." ::= { cfrExtCircuitEntry 13 } cfrExtCircuitMinThruputIn OBJECT-TYPE SYNTAX INTEGER(9600..1544000) -- Units -- bits per second ACCESS read-only STATUS mandatory DESCRIPTION "Circuit's incoming minimal Throughput based on configuration." ::= { cfrExtCircuitEntry 14 } cfrExtCircuitBcastPktOuts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of broadcast packets sent out to the network." ::= { cfrExtCircuitEntry 15 } cfrExtCircuitBcastByteOuts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes sent out to the network in broadcast packets." ::= { cfrExtCircuitEntry 16 } cfrExtCircuitBandwidth OBJECT-TYPE SYNTAX INTEGER(0..16777215) -- Units -- bits per second ACCESS read-only STATUS mandatory DESCRIPTION "Bandwidth of the virtual circuit, acquired from Cisco typed LMI Full Status message." ::= { cfrExtCircuitEntry 17 } cfrExtCircuitShapeByteLimit OBJECT-TYPE SYNTAX INTEGER(125..2147483647) -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Maximum number of tokens a token bucket can hold in any time interval in case of traffic shaping." ::= { cfrExtCircuitEntry 18 } cfrExtCircuitShapeInterval OBJECT-TYPE SYNTAX INTEGER(10..125) -- Units -- milliseconds ACCESS read-only STATUS mandatory DESCRIPTION "Committed rate measurement interval." ::= { cfrExtCircuitEntry 19 } cfrExtCircuitShapeByteIncrement OBJECT-TYPE SYNTAX INTEGER(125..2147483647) -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Number of tokens added into the token bucket per time interval in case of traffic shaping." ::= { cfrExtCircuitEntry 20 } cfrExtCircuitShapePkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of packets that went through traffic shaping." ::= { cfrExtCircuitEntry 21 } cfrExtCircuitShapeBytes OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes that went through traffic shaping." ::= { cfrExtCircuitEntry 22 } cfrExtCircuitShapePktsDelay OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of packets that were delayed by the traffic shaper." ::= { cfrExtCircuitEntry 23 } cfrExtCircuitShapeBytesDelay OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes that were delayed by the traffic shaper." ::= { cfrExtCircuitEntry 24 } cfrExtCircuitShapeActive OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "Shows whether shaping is active or not." ::= { cfrExtCircuitEntry 25 } cfrExtCircuitShapeAdapting OBJECT-TYPE SYNTAX INTEGER { none(1), becn(2), foreSight(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of Adaptive Shaping configured. none(1) - No adaptive shaping configured becn(2) - Backward Explicit Congestion Notification foreSight(3) - ForeSight is the network traffic control software used in Cisco WAN switches" ::= { cfrExtCircuitEntry 26 } cfrExtCircuitTxDataRate OBJECT-TYPE SYNTAX INTEGER(1..45000000) ACCESS read-only STATUS mandatory DESCRIPTION "The average rate (bytes/second) at which data is transmitted in this circuit. " ::= { cfrExtCircuitEntry 27 } cfrExtCircuitTxPktRate OBJECT-TYPE SYNTAX INTEGER(1..45000000) ACCESS read-only STATUS mandatory DESCRIPTION "The average number of packets sent in a second in this circuit." ::= { cfrExtCircuitEntry 28 } cfrExtCircuitRcvDataRate OBJECT-TYPE SYNTAX INTEGER(1..45000000) ACCESS read-only STATUS mandatory DESCRIPTION "The average rate (bytes/second) at which data is received in this circuit. " ::= { cfrExtCircuitEntry 29 } cfrExtCircuitRcvPktRate OBJECT-TYPE SYNTAX INTEGER(1..45000000) ACCESS read-only STATUS mandatory DESCRIPTION "The average number of packets received in a second in this circuit. " ::= { cfrExtCircuitEntry 30 } cfrMapTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of protocols and addresses mapping information of FR virtual circuit." ::= { cfrMapObjs 1 } cfrMapEntry OBJECT-TYPE SYNTAX CfrMapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains one mapping information of a Frame Relay virtual circuit." INDEX { frCircuitIfIndex, frCircuitDlci, cfrMapIndex } ::= { cfrMapTable 1 } CfrMapEntry ::= SEQUENCE { cfrMapIndex INTEGER, cfrMapProtocol CfrMapProtocols, cfrMapAddress OCTET STRING, cfrMapType INTEGER, cfrMapEncaps INTEGER, cfrMapBroadcast TruthValue, cfrMapPayloadCompress TruthValue, cfrMapTcpHdrCompress INTEGER, cfrMapRtpHdrCompress INTEGER, cfrMapPayloadCompressType INTEGER } cfrMapIndex OBJECT-TYPE SYNTAX INTEGER(1..999) ACCESS read-only STATUS mandatory DESCRIPTION "An arbitrary Index to the mapping information associated with a certain circuit. The maximum value is arbitrarily picked which is considered sufficient for usual configuration." ::= { cfrMapEntry 1 } cfrMapProtocol OBJECT-TYPE SYNTAX CfrMapProtocols -- Rsyntax INTEGER { -- arp(1), -- serialArp(6), -- ip(7), -- xns(10), -- novell(11), -- apollo(12), -- vines(13), -- appletalk(16), -- ieeeSpanning(18), -- decnet(22), -- clns(25), -- rsrb(37), -- bridge(38), -- stun(39), -- frArp(40), -- uncompressedTcp(47), -- compressedTcp(48), -- llc2(49), -- frSwitch(53), -- dlsw(63), -- nhrp(74), -- compressedRtp(83), -- wildcard(999) -- } ACCESS read-only STATUS mandatory DESCRIPTION "Mapping protocol for this circuit." ::= { cfrMapEntry 2 } cfrMapAddress OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..64)) ACCESS read-only STATUS mandatory DESCRIPTION "Mapping protocol address at remote end for this DLCI. NOTE: For point-to-point DLCI, the string is fixed to be point-to-point." ::= { cfrMapEntry 3 } cfrMapType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), svc(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Type for the map creation." ::= { cfrMapEntry 4 } cfrMapEncaps OBJECT-TYPE SYNTAX INTEGER { ietf(1), cisco(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indication of the encapsulation type for this mapping protocol." ::= { cfrMapEntry 5 } cfrMapBroadcast OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "Broadcast enabled or disabled." ::= { cfrMapEntry 6 } cfrMapPayloadCompress OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS deprecated DESCRIPTION "Indicate if payload compression is enabled." ::= { cfrMapEntry 7 } cfrMapTcpHdrCompress OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), passive(2), active(3) } ACCESS read-only STATUS mandatory DESCRIPTION "TCP header compression type, if applicable." ::= { cfrMapEntry 8 } cfrMapRtpHdrCompress OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), passive(2), active(3) } ACCESS read-only STATUS mandatory DESCRIPTION "RTP header compression type, if applicable. The value 'passive' means that the header of an outgoing RTP/IP packet is compressed only if an incoming RTP/IP packet had a compressed header. The value 'active' means the header of every outgoing RTP/IP packet is compressed." ::= { cfrMapEntry 9 } cfrMapPayloadCompressType OBJECT-TYPE SYNTAX INTEGER { inapplicable(1), cisco(2), frf9Software(3), frf9Hardware(4) } ACCESS read-only STATUS mandatory DESCRIPTION "FR payload compression type, if applicable. FRF.9 is the Frame Relay Forum Implementation Agreement on FR payload compression. The compression can be done by either software or hardware (when equipped with the supporting hardware), depending on configuration." REFERENCE "Frame Relay Forum document number FRF.9" ::= { cfrMapEntry 10 } cfrSvcTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrSvcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of FR SVC specific, descriptive and statistics information." ::= { cfrSvcObjs 1 } cfrSvcEntry OBJECT-TYPE SYNTAX CfrSvcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains circuit information specific to a Frame Relay Switched Virtual Circuit." INDEX { frCircuitIfIndex, frCircuitDlci } ::= { cfrSvcTable 1 } CfrSvcEntry ::= SEQUENCE { cfrSvcAddrLocal OCTET STRING, cfrSvcAddrRemote OCTET STRING, cfrSvcThroughputIn INTEGER, cfrSvcMinThruputOut INTEGER, cfrSvcMinThruputIn INTEGER, cfrSvcCommitBurstIn INTEGER, cfrSvcExcessBurstIn INTEGER, cfrSvcIdleTime INTEGER } cfrSvcAddrLocal OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..64)) ACCESS read-only STATUS mandatory DESCRIPTION "Local E.164/X.125 address for the circuit." ::= { cfrSvcEntry 1 } cfrSvcAddrRemote OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..64)) ACCESS read-only STATUS mandatory DESCRIPTION "Remote E.164/X.125 address for the circuit." ::= { cfrSvcEntry 2 } cfrSvcThroughputIn OBJECT-TYPE SYNTAX INTEGER(9600..1544000) -- Units -- bits per second ACCESS read-only STATUS mandatory DESCRIPTION "Circuit's incoming throughput. For outgoing throughput (commonly referred to as CIR) see frCircuitThroughput per RFC1315." ::= { cfrSvcEntry 3 } cfrSvcMinThruputOut OBJECT-TYPE SYNTAX INTEGER(9600..1544000) -- Units -- bits per second ACCESS read-only STATUS deprecated DESCRIPTION "Circuit's outgoing minimal Throughput." ::= { cfrSvcEntry 4 } cfrSvcMinThruputIn OBJECT-TYPE SYNTAX INTEGER(9600..1544000) -- Units -- bits per second ACCESS read-only STATUS deprecated DESCRIPTION "Circuit's incoming minimal Throughput." ::= { cfrSvcEntry 5 } cfrSvcCommitBurstIn OBJECT-TYPE SYNTAX INTEGER(9600..1544000) ACCESS read-only STATUS mandatory DESCRIPTION "Circuit's incoming Committed Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing CBR, see frCircuitCommittedBurst per RFC 1315." ::= { cfrSvcEntry 6 } cfrSvcExcessBurstIn OBJECT-TYPE SYNTAX INTEGER(9600..2440000) ACCESS read-only STATUS mandatory DESCRIPTION "Circuit's incoming Excess Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing EBR, see frCircuitExcessBurst per RFC 1315." ::= { cfrSvcEntry 7 } cfrSvcIdleTime OBJECT-TYPE SYNTAX INTEGER -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Circuit's idle time period. If expires, the circuit is cleared." ::= { cfrSvcEntry 8 } cfrElmiIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "This object represents the Management address of the device used for address registration. Network management station can send management messages to this IP address. This can be user configured address or the address of one of the interfaces on the device. If address registration is disabled then this will have a value of 0.0.0.0. This object is accessible only if the ELMI protocol is supported on the device" ::= { cfrElmiObjs 1 } cfrElmiTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrElmiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of CISCO Frame Relay ELMI information that is specific to CISCO implementation" ::= { cfrElmiObjs 2 } cfrElmiEntry OBJECT-TYPE SYNTAX CfrElmiEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains information about a physical interface. The table can be accessible only if the device supports ELMI protocol and if LMI is enabled on the interface." INDEX { ifIndex } ::= { cfrElmiTable 1 } CfrElmiEntry ::= SEQUENCE { cfrElmiLinkStatus INTEGER, cfrElmiArStatus INTEGER, cfrElmiRemoteStatus INTEGER } cfrElmiLinkStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable states whether Enhanced Link Management Interface(ELMI) protocol is enabled or not on a frame relay interface." ::= { cfrElmiEntry 1 } cfrElmiArStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable states whether the Enhanced Link Management Interface(ELMI) address registration(AR) mechanism is enabled or not on a frame relay interface. A value of 1 indicates ELMI AR is supported on the interface. A value of 2 indicates ELMI AR is supported but the user disabled the exchange of IP address and ifIndex with the neighboring device. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface." ::= { cfrElmiEntry 2 } cfrElmiRemoteStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable states the Enhanced Link Management(ELMI) status on the other end of the interface. If cfrElmiLinkStatus is enabled on the other end a value of 1 will be returned, else 2 will be returned. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface" ::= { cfrElmiEntry 3 } cfrElmiNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrElmiNeighborEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of CISCO Frame Relay Neighbor ELMI information that is specific to CISCO implementation." ::= { cfrElmiObjs 3 } cfrElmiNeighborEntry OBJECT-TYPE SYNTAX CfrElmiNeighborEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains information of the neighboring device connected to a physical interface. The entry will be present only if ELMI is enabled on the neighboring device interface. If the value of the cfrElmiRemoteStatus in the cfrElmiEntry is 1 then a valid entry exists for the interface. If ELMI is not supported on the remote end then, the neighbor information for the interface will not be present" INDEX { ifIndex } ::= { cfrElmiNeighborTable 1 } CfrElmiNeighborEntry ::= SEQUENCE { cfrElmiNeighborArStatus INTEGER, cfrElmiNeighborIpAddress IpAddress, cfrElmiNeighborIfIndex InterfaceIndex, cfrElmiNeighborVendorName DisplayString, cfrElmiNeighborPlatformName DisplayString, cfrElmiNeighborDeviceName DisplayString } cfrElmiNeighborArStatus OBJECT-TYPE SYNTAX INTEGER { notsupported(1), enabled(2), disabled(3) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates the status of ELMI Address registration(AR) on the neighboring device. A value of 1 indicates ELMI AR is not supported on the neighboring device. A value of 2 indicates ELMI AR is enabled on the interface. A value of 3 indicates AR is supported, but user disabled the exchange of IP address and ifIndex with the neighbor." ::= { cfrElmiNeighborEntry 1 } cfrElmiNeighborIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Management IP address of the neighboring device to which the other end of this interface is connected. Network management system can use this address to send management messages to the device. If address registration is not supported on the remote end then the value will be 0.0.0.0. NMS uses this object in the topology discovery of the network." ::= { cfrElmiNeighborEntry 2 } cfrElmiNeighborIfIndex OBJECT-TYPE SYNTAX InterfaceIndex -- Rsyntax INTEGER(1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "The Interface index of the neighboring device to which this interface is connected. If the value of cfrElmiNeighborArStatus is 2 then this will have a valid value. If the value of cfrElmiNeighborArStatus is 3 or 1 then value of this object will be 0. NMS uses this object in the topology discovery of the network." ::= { cfrElmiNeighborEntry 3 } cfrElmiNeighborVendorName OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Vendor name of the neighboring device to which the other end of this interface is connected." ::= { cfrElmiNeighborEntry 4 } cfrElmiNeighborPlatformName OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Platform name of the neighboring device to which the other end of this interface is connected." ::= { cfrElmiNeighborEntry 5 } cfrElmiNeighborDeviceName OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Device name of the neighboring device to which the other end of this interface is connected." ::= { cfrElmiNeighborEntry 6 } cfrFragTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrFragEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of Frame Relay Fragmentation information. These are specific to Cisco's implementation." ::= { cfrFragObjs 1 } cfrFragEntry OBJECT-TYPE SYNTAX CfrFragEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains details of fragmentation configured on this circuit. " INDEX { frCircuitIfIndex, frCircuitDlci } ::= { cfrFragTable 1 } CfrFragEntry ::= SEQUENCE { cfrFragSize INTEGER, cfrFragType DisplayString, cfrFragInPkts Counter, cfrFragOutPkts Counter, cfrFragInOctets Counter, cfrFragOutOctets Counter, cfrFragNotInPkts Counter, cfrFragNotOutPkts Counter, cfrFragNotInOctets Counter, cfrFragNotOutOctets Counter, cfrFragAssembledInPkts Counter, cfrFragAssembledInOctets Counter, cfrFragPreOutPkts Counter, cfrFragPreOutOctets Counter, cfrFragDroppedReAssembledInPkts Counter, cfrFragDroppedFragmentedOutPkts Counter, cfrFragTimeoutsIn INTEGER, cfrFragOutOfSeqFragPkts Counter, cfrFragUnexpectedBBitSetPkts Counter, cfrFragSeqMissedPkts Counter, cfrFragInterleavedOutPkts Counter } cfrFragSize OBJECT-TYPE SYNTAX INTEGER(16..1600) -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "cfrFragSize defines the payload size of a fragment and it excludes the FR headers and any FR fragmentation header." ::= { cfrFragEntry 1 } cfrFragType OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Fragmentation type configured by the user. The types supported are end-to-end, VoFR-cisco and VoFR." ::= { cfrFragEntry 2 } cfrFragInPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames received that have a fragmentation header." ::= { cfrFragEntry 3 } cfrFragOutPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of fragments that are transmitted with a fragmenation header." ::= { cfrFragEntry 4 } cfrFragInOctets OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes received in frames that have a fragmentation header. The number of bytes include the FR header." ::= { cfrFragEntry 5 } cfrFragOutOctets OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes that are transmitted in frames with a fragmenation header. The number of bytes also includes the FR header." ::= { cfrFragEntry 6 } cfrFragNotInPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames received that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 7 } cfrFragNotOutPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames transmitted without fragmenting and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 8 } cfrFragNotInOctets OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes received in frames that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 9 } cfrFragNotOutOctets OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes transmitted in frames that are not fragmented and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set." ::= { cfrFragEntry 10 } cfrFragAssembledInPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { cfrFragEntry 11 } cfrFragAssembledInOctets OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes received in fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e.in un-fragmentated pkts)." ::= { cfrFragEntry 12 } cfrFragPreOutPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames fragmented and trasmitted. It also counts the number of packets trasmitted without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { cfrFragEntry 13 } cfrFragPreOutOctets OBJECT-TYPE SYNTAX Counter -- Units -- octets ACCESS read-only STATUS mandatory DESCRIPTION "Total number of bytes transmitted in fragmented frames. It also counts the number of bytes trasmitted in frames without FR fragmentation header (i.e. in un-fragmentated pkts)." ::= { cfrFragEntry 14 } cfrFragDroppedReAssembledInPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of received fragments dropped for reasons such as : running out of memory, receiving segments out of sequence, receiving an unexpected frame with a B bit set, timing out on a reassembling frame." ::= { cfrFragEntry 15 } cfrFragDroppedFragmentedOutPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of fragments dropped because of running out of memory." ::= { cfrFragEntry 16 } cfrFragTimeoutsIn OBJECT-TYPE SYNTAX INTEGER(0..1000) ACCESS read-only STATUS mandatory DESCRIPTION "Number of reassemble timer timeouts for this circuit. A frame requiring more than two minutes to fully reassemble is dropped and timeout will be incremented by one." ::= { cfrFragEntry 17 } cfrFragOutOfSeqFragPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the total number of packets received with an unexpected sequence number. All fragments being reassembled are dropped. Start a new packet with the received segment only if the B bit is set on the segment. Otherwise the new segment is also dropped." ::= { cfrFragEntry 18 } cfrFragUnexpectedBBitSetPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of fragments received in this circuit with a B bit set. All fragments being reassembled are dropped and a new packet is started with this segment." ::= { cfrFragEntry 19 } cfrFragSeqMissedPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of fragments received in this circuit with skipped sequence number." ::= { cfrFragEntry 20 } cfrFragInterleavedOutPkts OBJECT-TYPE SYNTAX Counter -- Units -- packets ACCESS read-only STATUS mandatory DESCRIPTION "Number of packets that have been interleaved between segments." ::= { cfrFragEntry 21 } cfrConnectionTable OBJECT-TYPE SYNTAX SEQUENCE OF CfrConnectionEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking connection information. These are specific to Cisco's implementation." ::= { cfrConnectionObjs 1 } cfrConnectionEntry OBJECT-TYPE SYNTAX CfrConnectionEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry of the table contains information of a connection that is established for Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking." INDEX { frCircuitIfIndex, frCircuitDlci } ::= { cfrConnectionTable 1 } CfrConnectionEntry ::= SEQUENCE { cfrConnName DisplayString, cfrConnID INTEGER, cfrConnState DisplayString, cfrConnSegment1Name DisplayString, cfrConnSegment1VCGroup DisplayString, cfrConnSegment1Dlci DlciNumber, cfrConnSegment2Name DisplayString, cfrConnSegment2Vpi INTEGER, cfrConnSegment2Vci INTEGER, cfrConnServiceTranslation INTEGER, cfrConnFrSscsDlci DlciNumber, cfrConnEfciBit INTEGER, cfrConnDeBit INTEGER, cfrConnClpBit INTEGER } cfrConnName OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "The textual name of a for FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 1 } cfrConnID OBJECT-TYPE SYNTAX INTEGER(1..2000) ACCESS read-only STATUS mandatory DESCRIPTION "The numerical identifier of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 2 } cfrConnState OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "Status of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 3 } cfrConnSegment1Name OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "The textual name used to identify the first segment of a FR/FR or FR/ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 4 } cfrConnSegment1VCGroup OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "The textual name used to identify the VC-Group in the first segment of a Frame Relay/ATM Network Interworking (FRF.5)connection. This field is not applicabe in case of, FRF.8 (Frame Relay/ATM Service Interworking) and FR-FR connectione. " ::= { cfrConnectionEntry 5 } cfrConnSegment1Dlci OBJECT-TYPE SYNTAX DlciNumber -- Rsyntax INTEGER(0..1023) ACCESS read-only STATUS mandatory DESCRIPTION "The DLCI used as the first segment of a FR-FR or FR-ATM Network/Service Interworking connection." ::= { cfrConnectionEntry 6 } cfrConnSegment2Name OBJECT-TYPE SYNTAX DisplayString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "The interface on which second segment of a FR-FR or FR-ATM Network/Service Interworking connection is configured." ::= { cfrConnectionEntry 7 } cfrConnSegment2Vpi OBJECT-TYPE SYNTAX INTEGER(0..4095) ACCESS read-only STATUS mandatory DESCRIPTION "The value of VPI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, the same will be used to display the DLCI used as the second segment." ::= { cfrConnectionEntry 8 } cfrConnSegment2Vci OBJECT-TYPE SYNTAX INTEGER(0..4095) ACCESS read-only STATUS mandatory DESCRIPTION "The value of VCI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, this is not supported." ::= { cfrConnectionEntry 9 } cfrConnServiceTranslation OBJECT-TYPE SYNTAX INTEGER { serviceTranslationEnabled(1), serviceTranslationNotEnabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Shows whether Service Translation Mode is supported or not. Translation Mode is the interworking of internetworking (routed and/or bridged) protocols used in FR-ATM Service PVC Interworking(FRF.8). This is not supported in case of FRF.5 (FR-ATM network Interworking) and FR-FR connections." ::= { cfrConnectionEntry 10 } cfrConnFrSscsDlci OBJECT-TYPE SYNTAX DlciNumber -- Rsyntax INTEGER(0..1023) ACCESS read-only STATUS mandatory DESCRIPTION "The DLCI value used at the FR-SSCS layer. This is one of connection multiplexing methods used in Frame Relay/ATM Network Interworking. Not supported in case of FRF.8 (FR-ATM Service PVC Interworking) and FR-FR connections" ::= { cfrConnectionEntry 11 } cfrConnEfciBit OBJECT-TYPE SYNTAX INTEGER { mapFecn(1), notMapFecn(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Shows whether the FECN field in the FR frame is mapped to the ATM EFCI field of every cell generated out of the FR frame. This is used to indicate congestion in FR to ATM direction in case of Frame Relay/ATM Service PVC Interworking. Not supported in FRF.5 (Frame Relay/ATM Network Interworking and FR-FR connections." ::= { cfrConnectionEntry 12 } cfrConnDeBit OBJECT-TYPE SYNTAX INTEGER { noMapClp(1), mapClp(2), setDe0(3), setDe1(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The method of operation for loss priority mapping in the B-ISDN to FR direction.. Not supported in case of FR-FR connection." ::= { cfrConnectionEntry 13 } cfrConnClpBit OBJECT-TYPE SYNTAX INTEGER { setClpTo0AndCopyDeToFrsscsDe(1), setClpTo1AndCopyDeToFrsscsDe(2), copyDeToFrsscsDeAndClp(3), copyDeToClp(4), setClp1(5), setClp0(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The method of operation used to map loss priority mapping in the FR to ATM direction. Not supported in case of FR-FR connection." ::= { cfrConnectionEntry 14 } ciscoFrMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 1 } -- OBJECT-GROUP -- Status -- deprecated -- Descr -- The compliance statement for entities which implement -- this Cisco Frame Relay MIB. -- objects -- cfrLmiLinkstatus, cfrLmiLinkType, cfrLmiEnquiryIns, -- cfrLmiEnquiryOuts, cfrLmiStatusIns, cfrLmiStatusOuts, -- cfrLmiUpdateStatusIns, cfrLmiUpdateStatusOuts, -- cfrLmiStatusTimeouts, cfrLmiStatusEnqTimeouts, cfrLmiN392Dce, -- cfrLmiN393Dce, cfrLmiT392Dce, cfrCircuitDEins, -- cfrCircuitDEouts, cfrCircuitDropPktsOuts, cfrCircuitType, -- cfrExtCircuitIfName, cfrExtCircuitIfType, -- cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, -- cfrExtCircuitCreateType, cfrExtCircuitMulticast, -- cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, cfrMapIndex, -- cfrMapProtocol, cfrMapAddress, cfrMapType, cfrMapEncaps, -- cfrMapBroadcast, cfrMapPayloadCompress, cfrMapTcpHdrCompress, -- cfrSvcAddrLocal, cfrSvcAddrRemote, cfrSvcThroughputIn, -- cfrSvcMinThruputOut, cfrSvcMinThruputIn, cfrSvcCommitBurstIn, -- cfrSvcExcessBurstIn, cfrSvcIdleTime ciscoFrMIBGroupRev1 OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 2 } -- OBJECT-GROUP -- Status -- deprecated -- Descr -- A collection of objects providing router's -- Frame Relay configuration and statistics -- information that are additional to the IETF -- standard Frame Relay DTE MIB. -- objects -- cfrLmiLinkstatus, cfrLmiLinkType, cfrLmiEnquiryIns, -- cfrLmiEnquiryOuts, cfrLmiStatusIns, cfrLmiStatusOuts, -- cfrLmiUpdateStatusIns, cfrLmiUpdateStatusOuts, -- cfrLmiStatusTimeouts, cfrLmiStatusEnqTimeouts, cfrLmiN392Dce, -- cfrLmiN393Dce, cfrLmiT392Dce, cfrCircuitDEins, -- cfrCircuitDEouts, cfrCircuitDropPktsOuts, cfrCircuitType, -- cfrExtCircuitIfName, cfrExtCircuitIfType, -- cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, -- cfrExtCircuitCreateType, cfrExtCircuitMulticast, -- cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, -- cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts, -- cfrMapIndex, cfrMapProtocol, cfrMapAddress, cfrMapType, -- cfrMapEncaps, cfrMapBroadcast, cfrMapTcpHdrCompress, -- cfrMapRtpHdrCompress, cfrMapPayloadCompressType, -- cfrSvcAddrLocal, cfrSvcAddrRemote, cfrSvcThroughputIn, -- cfrSvcMinThruputOut, cfrSvcMinThruputIn, cfrSvcCommitBurstIn, -- cfrSvcExcessBurstIn, cfrSvcIdleTime ciscoFrLmiMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 3 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects providing router's -- Frame Relay LMI configuration and statistics -- information either supplemental to the -- frDlcmiTable of RFC 1315 or specific to Cisco's -- implementation. -- objects -- cfrLmiLinkstatus, cfrLmiLinkType, cfrLmiEnquiryIns, -- cfrLmiEnquiryOuts, cfrLmiStatusIns, cfrLmiStatusOuts, -- cfrLmiUpdateStatusIns, cfrLmiUpdateStatusOuts, -- cfrLmiStatusTimeouts, cfrLmiStatusEnqTimeouts, cfrLmiN392Dce, -- cfrLmiN393Dce, cfrLmiT392Dce ciscoFrCircuitMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 4 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects providing information of a -- circuit that are not included in frCircuitTable of -- RFC1315 but are generic to Frame Relay. -- objects -- cfrCircuitDEins, cfrCircuitDEouts, cfrCircuitDropPktsOuts, -- cfrCircuitType ciscoExtCircuitMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 5 } -- OBJECT-GROUP -- Status -- deprecated -- Descr -- A collection of objects that provide Cisco -- implementation specific FR circuit information. -- This is a Cisco extension for the frCircuitTable -- of RFC 1315. -- objects -- cfrExtCircuitIfName, cfrExtCircuitIfType, -- cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, -- cfrExtCircuitCreateType, cfrExtCircuitMulticast, -- cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, -- cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts, -- cfrExtCircuitFECNOuts, cfrExtCircuitBECNOuts, -- cfrExtCircuitMinThruputOut, cfrExtCircuitMinThruputIn, -- cfrExtCircuitBcastPktOuts, cfrExtCircuitBcastByteOuts, -- cfrExtCircuitBandwidth ciscoExtCircuitMIBGroup1 OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 13 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects that provide Cisco -- implementation specific FR circuit information. -- This is a Cisco extension for the frCircuitTable -- of RFC 1315. -- objects -- cfrExtCircuitIfName, cfrExtCircuitIfType, -- cfrExtCircuitSubifIndex, cfrExtCircuitMapStatus, -- cfrExtCircuitCreateType, cfrExtCircuitMulticast, -- cfrExtCircuitRoutedDlci, cfrExtCircuitRoutedIf, -- cfrExtCircuitUncompressIns, cfrExtCircuitUncompressOuts, -- cfrExtCircuitFECNOuts, cfrExtCircuitBECNOuts, -- cfrExtCircuitMinThruputOut, cfrExtCircuitMinThruputIn, -- cfrExtCircuitBcastPktOuts, cfrExtCircuitBcastByteOuts, -- cfrExtCircuitBandwidth, cfrExtCircuitTxDataRate, -- cfrExtCircuitTxPktRate, cfrExtCircuitRcvDataRate, -- cfrExtCircuitRcvPktRate ciscoFrTsMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 6 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects that provide information -- about Frame Relay Traffic Shaping. These are -- additional to the IETF standard Frame Relay DTE MIB. -- objects -- cfrExtCircuitShapeByteLimit, cfrExtCircuitShapeInterval, -- cfrExtCircuitShapeByteIncrement, cfrExtCircuitShapePkts, -- cfrExtCircuitShapeBytes, cfrExtCircuitShapePktsDelay, -- cfrExtCircuitShapeBytesDelay, cfrExtCircuitShapeActive, -- cfrExtCircuitShapeAdapting ciscoFrMapMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 7 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects to provide mapping -- information of a Frame Relay virtual circuit. -- These are additional to the IETF standard -- Frame Relay DTE MIB. -- objects -- cfrMapIndex, cfrMapProtocol, cfrMapAddress, cfrMapType, -- cfrMapEncaps, cfrMapBroadcast, cfrMapTcpHdrCompress, -- cfrMapRtpHdrCompress, cfrMapPayloadCompressType ciscoFrSvcMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 8 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects to provide circuit -- information specific to a Frame Relay Switched -- Virtual Circuit.This is in addition to the IETF -- standard Frame Relay DTE MIB. -- objects -- cfrSvcAddrLocal, cfrSvcAddrRemote, cfrSvcThroughputIn, -- cfrSvcCommitBurstIn, cfrSvcExcessBurstIn, cfrSvcIdleTime ciscoFrElmiMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 9 } -- OBJECT-GROUP -- Status -- deprecated -- Descr -- A collection of objects providing router's -- ELMI information. -- objects -- cfrElmiIpAddr, cfrElmiArStatus, cfrElmiRemoteStatus, -- cfrElmiNeighborArStatus, cfrElmiNeighborIpAddress, -- cfrElmiNeighborIfIndex, cfrElmiNeighborVendorName, -- cfrElmiNeighborPlatformName, cfrElmiNeighborDeviceName ciscoFrElmiMIBGroup1 OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 10 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects providing router's -- ELMI information. -- objects -- cfrElmiIpAddr, cfrElmiArStatus, cfrElmiRemoteStatus, -- cfrElmiNeighborArStatus, cfrElmiNeighborIpAddress, -- cfrElmiNeighborIfIndex, cfrElmiNeighborVendorName, -- cfrElmiNeighborPlatformName, cfrElmiNeighborDeviceName, -- cfrElmiLinkStatus ciscoFrFragMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 11 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects providing router's -- fragmentation information. -- objects -- cfrFragSize, cfrFragType, cfrFragInPkts, cfrFragOutPkts, -- cfrFragInOctets, cfrFragOutOctets, cfrFragNotInPkts, -- cfrFragNotOutPkts, cfrFragNotInOctets, cfrFragNotOutOctets, -- cfrFragAssembledInPkts, cfrFragAssembledInOctets, -- cfrFragPreOutPkts, cfrFragPreOutOctets, -- cfrFragDroppedReAssembledInPkts, -- cfrFragDroppedFragmentedOutPkts, cfrFragTimeoutsIn, -- cfrFragOutOfSeqFragPkts, cfrFragUnexpectedBBitSetPkts, -- cfrFragSeqMissedPkts, cfrFragInterleavedOutPkts ciscoFrConnMIBGroup OBJECT IDENTIFIER ::= { ciscoFrMIBGroups 12 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects providing router's -- fragmentation information. -- objects -- cfrConnName, cfrConnID, cfrConnState, cfrConnSegment1Name, -- cfrConnSegment1VCGroup, cfrConnSegment1Dlci, -- cfrConnSegment2Name, cfrConnSegment2Vpi, cfrConnSegment2Vci, -- cfrConnServiceTranslation, cfrConnFrSscsDlci, cfrConnEfciBit, -- cfrConnDeBit, cfrConnClpBit ciscoFrMIBCompliance OBJECT IDENTIFIER ::= { ciscoFrMIBCompliances 1 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for entities which implement -- this Cisco Frame Relay MIB. -- Module -- >>current<< -- MandGroup -- ciscoFrMIBGroup ciscoFrMIBCompliancesRev1 OBJECT IDENTIFIER ::= { ciscoFrMIBCompliances 2 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for entities which implement -- this Cisco Frame Relay MIB. -- Module -- >>current<< -- MandGroup -- ciscoFrMIBGroupRev1 ciscoFrMIBCompliancesRev2 OBJECT IDENTIFIER ::= { ciscoFrMIBCompliances 3 } -- MODULE-COMPLIANCE -- Status -- obsolete -- Descr -- The compliance statement for entities which implement -- this Cisco Frame Relay MIB. -- Module -- >>current<< -- MandGroup -- ciscoFrLmiMIBGroup -- MandGroup -- ciscoFrCircuitMIBGroup -- MandGroup -- ciscoExtCircuitMIBGroup -- MandGroup -- ciscoFrTsMIBGroup -- MandGroup -- ciscoFrMapMIBGroup -- MandGroup -- ciscoFrSvcMIBGroup ciscoFrMIBCompliancesRev3 OBJECT IDENTIFIER ::= { ciscoFrMIBCompliances 4 } -- MODULE-COMPLIANCE -- Status -- deprecated -- Descr -- The compliance statement for entities which implement -- this Cisco Frame Relay MIB. -- Module -- >>current<< -- MandGroup -- ciscoFrLmiMIBGroup -- MandGroup -- ciscoFrCircuitMIBGroup -- MandGroup -- ciscoExtCircuitMIBGroup -- MandGroup -- ciscoFrTsMIBGroup -- MandGroup -- ciscoFrMapMIBGroup -- MandGroup -- ciscoFrSvcMIBGroup -- MandGroup -- ciscoFrElmiMIBGroup ciscoFrMIBCompliancesRev4 OBJECT IDENTIFIER ::= { ciscoFrMIBCompliances 5 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for entities which implement -- this Cisco Frame Relay MIB. -- Module -- >>current<< -- MandGroup -- ciscoFrLmiMIBGroup -- MandGroup -- ciscoFrCircuitMIBGroup -- MandGroup -- ciscoExtCircuitMIBGroup1 -- MandGroup -- ciscoFrTsMIBGroup -- MandGroup -- ciscoFrMapMIBGroup -- MandGroup -- ciscoFrSvcMIBGroup -- MandGroup -- ciscoFrElmiMIBGroup1 -- MandGroup -- ciscoFrFragMIBGroup -- MandGroup -- ciscoFrConnMIBGroup END