-- MIB file created 18-Nov-2010 15:53:36, by -- SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com CISCO-ITP-TC-MIB DEFINITIONS ::= BEGIN -- From file: "CISCO-ITP-TC-MIB.my" -- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T" IMPORTS ciscoMgmt FROM CISCO-SMI Gauge FROM RFC1155-SMI; ciscoItpTextualConventions OBJECT IDENTIFIER ::= { ciscoMgmt 231 } -- MODULE-IDENTITY -- LastUpdated -- 200404260000Z -- OrgName -- Cisco Systems, Inc. -- ContactInfo -- Cisco Systems, Inc -- Customer Service -- -- Postal: 170 W. Tasman Drive -- San Jose, CA 95134 -- USA -- -- Tel: +1 800 553-NETS -- -- E-mail: cs-ss7@cisco.com -- Descr -- The defines textual conventions used by to manage -- devices related to the SS7 network. The -- relevant ITU documents describing this technology is -- the ITU Q series, including ITU Q.700: Introduction to -- CCITT Signalling System No. 7 and ITU Q.701 Functional -- description of the message transfer part (MTP) of -- Signalling System No. 7. -- -- Abbreviations: -- CDPA - Called Party Point Code -- CGPA - Calling Party Point Code -- CLLI - Common Language Location Codes -- CR - Connection Request message -- CREF - Connection Refusal message -- DPC - Destination Point Code -- ERR - Error message -- GTA - Global Title Address -- GTI - Global Title Indicator -- GTT - Global Title Translation -- LUDT - long unitdata message -- LUDTS - long unitdata service message -- M2PA - MTP2 Peer-to-Peer Adaptation Layer -- M3UA - MTP3-User Adaptation -- MAP - Mated Application Table -- MSU - Message Signal Unit -- MTP - Message Transport Protocol -- MTP2 - Layer 2 of Message Transport Protocol -- MTP3 - Layer 3 of Message Transport Protocol -- NAI - Nature of Address Indicator -- NP - Numbering Plan -- NTT - The Japanese Nippon Telephone & Telegraph -- OPC - Originating Point Code -- PC - Point Code -- RTN - Route Table Name -- RSR - Reset Request message -- SCCP - Signalling Connection Control Part -- SCTP - Stream Transmission Protocol(RFC 2960) -- SI - Signalling Indicator -- SP - Signalling Point -- SLC - Signalling Link Code -- SLS - Signalling Link Selector -- SSN - Subsystem Number -- SUA - SCCP-User Adaptation -- TFR - Transfer Restricted messages -- TT - Title Translation -- TTC - The Japanese Telecommunications Technology -- Committee -- UDT - unitdata message -- UDTS - unitdata service message -- XUDT - extended unitdata message -- XUDTS - extended unitdata service message -- RevDate -- 200404260000Z -- RevDescr -- Updated CItpTcPointCodeType to allow M3UA and -- SUA point-code types. -- RevDate -- 200308030000Z -- RevDescr -- Updated CItpTcPointCode textual convention to -- include descriptions for Japanese NTT and TTC -- variants. -- RevDate -- 200301290000Z -- RevDescr -- Added textual convention used to support the -- ability to define multiple instances of the -- signalling points. The following textual conventions -- were added. -- CItpTcNetworkName -- CItpTcInstanceNumber -- CItpTcSls -- -- Also deprecated CItpTcGtaAddr and CItpTcGtaDisplayZB. -- Added CItpTcGtaLongAddr and CItpTcGtaLongDisplay. -- -- Added new enumerated value to CItpTcLinkType object -- for virtual link used to connect signalling points -- acting as gateways. -- RevDate -- 200112110000Z -- RevDescr -- Added new enumerated value to CItpTcLinkType object -- for high speed link support. Add new enumerated -- value to the CItpTcSs7Variant object to support -- China national variant. A new textual convention has -- been added to address 0..15 range for Global Title -- addresses. -- RevDate -- 200110010000Z -- RevDescr -- Initial version of this MIB module. CItpTcAclId ::= Gauge(0|2700..2999) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- An numeric Identifier used to specify an access list -- used to permit and deny packets based on MTP3 -- information. Either the value 0 or the value of access list -- identifier. A value of zero indicates that an access list -- is not specified. CItpTcCLLI ::= OCTET STRING(SIZE(0..11)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Common Language Location Codes (CLLI Codes). -- An 11-character standardized geographic identifier -- that uniquely identifies the geographic location of -- telecommunication equipment. -- -- The CLLI code is supported as octet string containing -- administrative information in human-readable form. -- -- The use of control codes should be avoided. -- -- The use of newline should be avoided. -- -- The use of leading or trailing white space should -- be avoided. -- Refer -- Complete listings of geographical and geopolitical -- codes can be found in the BR 751-401-xxx series and -- BR 751-100-055, respectively. CItpTcDisplayPC ::= OCTET STRING(SIZE(1..12)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The Point Code in formatted based on the variant -- and the customer defined parameters. CItpTcEncodingSchemeValue ::= INTEGER(0..15) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The encoding scheme value. CItpTcGlobalTitleSelector ::= INTEGER { nai(1), tt(2), ttNpEs(3), ttNpNaiEs(4) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Global Title Selector. -- 'nai' : Global title translation based on -- nature of address indicator. -- -- 'tt' : Global title translation based on -- translation type. -- -- 'ttNpEs' : Global title translation based on -- translation type, numbering plan -- value and Encoding Scheme Value. -- -- 'ttNpNaiEs' : Global title translation based on -- translation type, numbering plan, -- value, nature of address indicator -- and encoding scheme value. CItpTcGlobalTitleSelectorName ::= OCTET STRING(SIZE(1..9)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The configured name associated with SCCP GTT -- Selector. -- -- An octet string specified by an administrator that -- must be in human-readable form. The names must -- conform to the allowed characters that can be -- specified via Command Line Interface(CLI). The -- names cannot contain control character and should -- not contain leading or trailing white space. CItpTcGtaAddr ::= OCTET STRING(SIZE(8)) -- TEXTUAL-CONVENTION -- Status -- deprecated -- Descr -- The configured digits in the SCCP GTT -- Global Title Address. -- -- An octet string specified by an administrator -- must be in human-readable form. The names must -- conform to the allowed characters that can be -- specified via Command Line Interface(CLI). The -- names cannot contain control character and should -- not contain leading or trailing white space. CItpTcGtaLongAddr ::= OCTET STRING(SIZE(0..64)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The configured hexadecimal digits in the SCCP GTT -- Global Title Address. CItpTcGtaDisplay ::= OCTET STRING(SIZE(1..15)) -- TEXTUAL-CONVENTION -- Status -- deprecated -- Descr -- The configured digits in the SCCP GTT -- Global Title Address. It consists of ASCII -- representation of GTA hex digits. -- -- This textual convention has been deprecated and -- replaced by CItpTcGtaDisplayZB. CItpTcGtaDisplayZB ::= OCTET STRING(SIZE(0..15)) -- TEXTUAL-CONVENTION -- Status -- deprecated -- Descr -- The configured digits in the SCCP GTT -- Global Title Address. It consists of ASCII -- representation of GTA hex digits. CItpTcGtaLongDisplay ::= OCTET STRING(SIZE(0..64)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The configured digits in the SCCP GTT -- Global Title Address. It consists of ASCII -- representation of GTA hex digits. CItpTcGtaDisplayLen ::= Gauge(1..15) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The SCCP GTT Global Title Address length. CItpTcGtaLongDisplayLen ::= Gauge(0..64) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The SCCP GTT Global Title Address length. CItpTcNetworkName ::= OCTET STRING(SIZE(0..19)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The network name is used to indicate the network -- in which this signalling point is participating. -- One or more instances of signalling points can -- exist in the same physical device. This identifier -- will be used to correlate instances of signalling -- points by network. -- -- When multiple instance support is not enable the -- network name will default to the null string. -- -- An octet string specified by an administrator that -- must be in human-readable form. The names must conform -- to the allowed characters that can be specified via -- Command Line Interface(CLI). The names cannot contain -- control character and should not contain leading or -- trailing white space. CItpTcInstanceNumber ::= Gauge(0..255) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The instance number used to select a particular -- Signalling point. CItpTcLinksetId ::= OCTET STRING(SIZE(1..19)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The configured name associated with an Signalling -- Point Linkset. -- -- An octet string specified by an administrator that must -- be in human-readable form. The names must conform to -- the allowed characters that can be specified via -- Command Line Interface(CLI). The names cannot contain -- control character and should not contain leading or -- trailing white space. CItpTcLinkSLC ::= Gauge(0..15) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The Signalling Link Code. This is the link identifier -- within a linkset. CItpTcLinkType ::= INTEGER { other(1), serial(2), sctpIp(3), hsl(4), virtual(5) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The link types. -- 'other' : This link is of some type not listed below. -- 'serial' : This link is a serial link transporting -- SS7 traffic. -- 'sctpIp' : This a SCTP/IP link transporting -- SS7 traffic. -- 'hsl' : This link is a high speed link using the ATM -- protocol for transporting SS7 traffic. -- 'virtual': This link is virtual link used to connect to -- instance of signalling point running on the -- same physical device. The link will be used to -- send and manage traffic between two signalling -- acting as a gateway. CItpTcNAI ::= INTEGER(0..255) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The SCCP GTT Network Address Indicator (NAI). -- The following values are generally used: -- Unknown Nature of Address (0), -- Subscriber Number (1), -- Reserved for national use (2), -- National Significant Number (3), -- International Number (4), -- Maximum NAI (127), -- Invalid NAI (253), -- Wild NAI (254). CItpTcNetworkIndicator ::= INTEGER { --?? enum value of zero may cause problems -- international(0), internationatSpare(1), national(2), nationalSpare(3) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Network Indicator: -- international - International network -- national - National network -- reserved - Reserved for national use -- spare - Spare (for international use only) -- 'international' : International network -- 'internationalSpare' : International network spare -- 'national' : National network -- 'nationalSpare' : National network Spare CItpTcNumberingPlan ::= INTEGER(0..255) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The SCCP GTT Numbering Plan (NP). -- The following values are generally used: -- Unknown NP (0), -- ISDN/Telephony NP (1), -- Spare (2), -- Data NP (3), -- Telex NP (4), -- Maritime Mobile NP (5), -- Land Mobile NP (6), -- ISDN/Mobile NP (7), -- Private NP (8). -- Max NP (15), -- Invalid NP (253), -- Wild NP (254). CItpTcPointCode ::= Gauge(0..16777216) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The SS7 network node address as specified in the -- following references. The format of the Point -- code depends on the variant defined in the -- CgspSS7Variant object as follows. -- -- 33222222222211111111110000000000 -- 10987654321098765432109876543210 -- ANSI: nnnnnnnn - Network -- cccccccc - Cluster -- mmmmmmmm - Member -- ITU: zzz - Zone -- aaaaaaaa - Area/Network -- iii - Identifier -- NTT: zzzzz - Zone -- aaaa - Area/Network -- iiiiiii - Identifier -- TTC: zzzzz - Zone -- aaaa - Area/Network -- iiiiiii - Identifier -- -- Note: The China variant has the same format as ANSI. -- -- This form of the point-code is not intended for -- for presentation. -- Refer -- The SS7 network node address as specified in the -- International Telecommunication Union standard Q.708: -- Specifications of Signalling System No. 7 - Numbering -- of International Signalling Point Codes, and by ANSI -- T1.111.8 Numbering of Signalling Point Codes. -- -- GF 001-9001 - Technical Specifications of Signalling -- System No. 7 for National Telephone Network of China. CItpTcPointCodeMask ::= Gauge(0..16777216) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- A mask used to perform different operations on -- pointcodes. -- Refer -- The SS7 network node address as specified in the -- International Telecommunication Union standard Q.708: -- Specifications of Signalling System No. 7 - Numbering -- of International Signalling Point Codes, and by ANSI -- T1.111.8 Numbering of Signalling Point Codes. CItpTcPointCodeType ::= INTEGER { primary(1), additional(2), capability(3), xua(4) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- List of the possible Point Code types. -- 'primary' : The primary point used to communicate -- information on the Signalling point. -- 'additional' : Additional point codes. -- 'capability' : capability point codes. -- 'xua' : MTP3-User Adaptation point codes or -- SCCP-User Adaptation point codes. CItpTcQos ::= Gauge(0..7|255) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The quality of service classification to be assigned -- to the IP packets used to transport the SS7 messages. -- The value can be from one to seven when selecting -- a Qos class or 255 to indicate the packet will not -- be assigned a Qos class. This value will be set to -- zero when cItpSpLinkType indicates that -- Quality of Service does not apply to this link. CItpTcRouteTableName ::= OCTET STRING(SIZE(1..19)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The configured name associated with an SP Route -- Table. -- -- An octet string specified by an administrator that must -- be in human-readable form. The names must conform to -- the allowed characters that can be specified via -- Command Line Interface(CLI). The names cannot contain -- control character and should not contain leading or -- trailing white space. CItpTcServiceIndicator ::= INTEGER { --?? enum value of zero may cause problems -- snmm(0), sntm(1), spare2(2), sccp(3), tup(4), isup(5), dupc(6), dupf(7), mtup(8), bisup(9), sisup(10), spare11(11), spare12(12), spare13(13), spare14(14), spare15(15) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The list of possible Service Indicator values. This -- identifies the type of SS7 packet. -- -- The service indicator codes for the international -- Signalling network are allocated as follows: -- -- 'SNMM' : Signalling network management -- messages (SNMM) -- 'SNTM' : Signalling network testing and -- maintenance messages (SNTM) -- 'Spare2' : Spare 2 -- 'SCCP' : SCCP -- 'TUP' : Telephone User Part (TUP) -- 'ISUP' : ISDN User Part (ISUP) -- 'DUPC' : Data User Part, call and circuit-related -- messages (DUPC) -- 'DUPF' : Data User Part, facility registration and -- cancellation messages (DUPF) -- 'MTUP' : Reserved for MTP Testing User Part (MTUP) -- 'BISUP' : Broadband ISDN User Part (BISUP) -- 'SISUP' : Satellite ISDN User Part (SISUP) -- 'Spare11' : Spare 11 -- 'Spare12' : Spare 12 -- 'Spare13' : Spare 13 -- 'Spare14' : Spare 14 -- 'Spare15' : Spare 15 -- Refer -- ITU Q.704 Signalling network functions and messages section -- 14.2.1 Service indicator. CItpTcSls ::= Gauge(0..255) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The Signalling Link Selector is a numeric value that -- contains the MTP3 packets to allow load balancing of -- traffic across a link within a linkset or combined linkset. -- Each linkset provides one or more tables used to map -- Signalling Link Selectors to Signalling Link Codes. The -- number of Signalling Link Selectors is 16 for ITU and 256 -- for ANSI. CItpTcSs7Variant ::= INTEGER { ansi(1), itu(2), china(3) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The list of SS7 variants. -- 'ANSI' : The ANSI variant of the SS7 specification. -- 'ITU' : The ITU variant of the SS7 specification. -- 'China' : The China national variant. This variant -- is a combination of ITU and ANSI. The -- protocol matches ITU except where the -- point-code has been expanded to ANSI format. -- Refer -- GF 001-9001 - Technical Specifications of Signalling -- System No. 7 for National Telephone Network of China. CItpTcSubSystemNumber ::= Gauge(0|2..255) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The SCCP Subsystem Number . A value of zero -- indicates that a subsystem is not specified. CItpTcSubSystemNumberMask ::= Gauge(2..255) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The SCCP Subsystem Number Mask. CItpTcTableLoadStatus ::= INTEGER { loadNotRequested(1), loadInProgress(2), loadComplete(3), loadCompleteWithErrors(4), loadFailed(5) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The status of the current or prior load operation. -- 'loadNotRequested' : load operations have not been -- requested. -- -- 'loadInProgress' : load request is active. -- -- 'loadComplete' : load request complete without errors. -- -- 'loadCompleteWithErrors' : Load request completed with -- some type of errors that -- prevented the adding of one -- or more entries. -- -- 'loadFailed' : Load request failed. CItpTcTimerMtp2T01 ::= Gauge(5000..150000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Alignment ready timer. The default and valid range is -- dependant on the value of variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 12500 16000 13000 -- ITU 40000 50000 40000 -- -- The SYNTAX statement allows values for both -- the ANSI, ITU variants and MTP2 Peer-to-Peer -- Adaptation Layer. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp2T02 ::= Gauge(0|5000..150000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Not aligned timer. The default and valid range is -- dependant on the value of variant. -- -- This timer is only applicable if cItpTcLinkType -- is serial. A get on this object will return a -- zero if the link is not serial. -- -- Min Max Def -- ====== ====== ====== -- ANSI 5000 14000 11500 -- ITU 5000 150000 5000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp2T03 ::= Gauge(0|1000..14000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Aligned timer. The default and valid range is -- dependant on the value of variant. -- -- This timer is only applicable if cItpTcLinkType -- is serial. A get on this object will return a -- zero if the link is not serial. -- -- Min Max Def -- ====== ====== ====== -- ANSI 5000 14000 11500 -- ITU 1000 2000 1500 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp2T04E ::= Gauge(0|400..660) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Proving period timer emergency timer. The default and -- valid range is dependant on the value of -- variant. -- -- This timer is only applicable if cItpTcLinkType -- is serial. A get on this object will return a -- zero if the link is not serial. -- -- Min Max Def -- ====== ====== ====== -- ANSI 540 660 600 -- ITU 400 600 500 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp2T04N ::= Gauge(0|2007..9500) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Proving period timer normal timer. The default and -- valid range is dependant on the value of -- variant. -- -- This timer is only applicable if cItpTcLinkType -- is serial. A get on this object will return a -- zero if the link is not serial. -- -- Min Max Def -- ====== ====== ====== -- ANSI 2007 2530 2300 -- ITU 7500 9500 8200 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp2T05 ::= Gauge(0|80..120) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Sending SIB timer. The default and valid range is -- dependant on the value of variant. -- -- This timer is only applicable if cItpTcLinkType -- is serial. A get on this object will return a -- zero if the link is not serial. -- -- Min Max Def -- ====== ====== ====== -- ANSI 80 120 80 -- ITU 80 120 100 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp2T06 ::= Gauge(1000..6000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Remote congestion timer. The default and valid range is -- dependant on the value of variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 1000 6000 1000 -- ITU 3000 6000 3000 -- -- The SYNTAX statement allows values for both -- the ANSI, ITU variants and MTP2 Peer-to-Peer -- Adaptation Layer. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp2T07 ::= Gauge(0|100..6000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Excessive delay of acknowledgement timer. The default -- and valid range is dependant on the value of -- variant(). -- -- This timer is only applicable if cItpTcLinkType -- is serial. A get on this object will return a -- zero if the link is not serial. -- -- Min Max Def -- ====== ====== ====== -- ANSI 500 2000 1000 -- ITU 500 2000 1000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.703 Signalling Link. -- ANSI T1.111.3 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T01 ::= Gauge(500..1200) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Delay to avoid message mis-sequencing on changeover. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 500 1200 800 -- ITU 500 1200 800 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T02 ::= Gauge(700..2000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for changeover acknowledgement. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 700 2000 1400 -- ITU 700 2000 1400 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T03 ::= Gauge(500..1200) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Time controlled diversion-delay to avoid -- mis-sequencing on change back. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 500 1200 800 -- ITU 500 1200 800 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T04 ::= Gauge(500..1200) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for change back acknowledgement (first -- attempt). -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 500 1200 800 -- ITU 500 1200 800 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T05 ::= Gauge(500..1200) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for change back acknowledgement (second -- attempt). -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 500 1200 800 -- ITU 500 1200 800 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T06 ::= Gauge(500..1200) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Delay to avoid message mis-sequencing on controlled -- rerouting. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 500 1200 800 -- ITU 500 1200 800 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T07 ::= Gauge(0|1000..2000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for Signalling data link connection -- acknowledgement. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 1000 2000 1500 -- ITU 1000 2000 1500 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. A value of zero -- indicates a value is not defined for a particular -- variant or is not supported by the implementation. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T08 ::= Gauge(800..1200) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Transfer prohibited inhibition timer (transient -- solution). -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 800 1200 1000 -- ITU 800 1200 1000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T10 ::= Gauge(30000..60000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting to repeat Signalling routeset test message. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 30000 60000 45000 -- ITU 30000 60000 45000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T11 ::= Gauge(30000..90000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Transfer restricted timer. (This is one way of -- implementing the function described in 13.4/Q.704 and -- mainly intended to simplify SPs.). -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 30000 90000 60000 -- ITU 30000 90000 60000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T12 ::= Gauge(800..1500) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for uninhibit acknowledgement. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 800 1500 1150 -- ITU 800 1500 1150 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T13 ::= Gauge(800..1500) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for force uninhibit. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 800 1500 1150 -- ITU 800 1500 1150 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T14 ::= Gauge(2000..3000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for inhibition acknowledgement. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 2000 3000 2500 -- ITU 2000 3000 2500 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T15 ::= Gauge(2000..3000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting to start Signalling routeset congestion -- test. Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 2000 3000 2500 -- ITU 2000 3000 2500 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T16 ::= Gauge(1400..2000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Waiting for routeset congestion status update. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 1400 2000 1700 -- ITU 1400 2000 1700 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T17 ::= Gauge(800..1500) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Delay to avoid oscillation of initial alignment -- failure and link restart. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 800 1500 1150 -- ITU 800 1500 1150 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T18 ::= Gauge(1000..31000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This timers servers different function based on the -- variant. -- -- ANSI: Repeat TFR once by response method -- ITU: MTP restart link supervision -- -- Min Max Def -- ====== ====== ====== -- ANSI 2000 20000 11000 -- ITU 1000 31000 30000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T19 ::= Gauge(67000..600000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This timers servers different function based on the -- variant. -- -- ANSI: failed craft timer referral timer -- ITU: supervision timer during MTP restart -- -- Min Max Def -- ====== ====== ====== -- ANSI 480000 600000 540000 -- ITU 67000 69000 68000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T20 ::= Gauge(1000..120000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This timers servers different function based on the -- variant. -- -- ANSI: waiting to repeat local inhibit test -- ITU: MTP restart timer at the Signalling point -- -- Min Max Def -- ====== ====== ====== -- ANSI 90000 120000 105000 -- ITU 1000 61000 60000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T21 ::= Gauge(63000..120000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This timers servers different function based on the -- variant. -- -- ANSI: waiting to repeat remote inhibit test) -- ITU: MTP restart timer at adjacent Signalling point -- -- Min Max Def -- ====== ====== ====== -- ANSI 90000 120000 105000 -- ITU 63000 65000 64000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T22 ::= Gauge(36000..360000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This timers servers different function based on the -- variant. -- -- ANSI: restarting SP waiting for Signalling links avail -- ITU: local inhibit test timer -- -- Min Max Def -- ====== ====== ====== -- ANSI 36000 60000 30000 -- ITU 80000 360000 300000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T23 ::= Gauge(9000..360000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This timers servers different function based on the -- variant. -- -- ANSI: restarting SP waiting to receive all TRA msgs -- ITU: remote inhibit test timer -- -- Min Max Def -- ====== ====== ====== -- ANSI 9000 60000 30000 -- ITU 80000 360000 300000 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T24 ::= Gauge(500..60000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This timers servers different function based on the -- variant. -- -- ANSI: restarting SP waiting to broadcast all TRA msgs -- ITU: stabilizing timer after local processor outage -- -- Min Max Def -- ====== ====== ====== -- ANSI 9000 60000 30000 -- ITU 500 500 500 -- -- The SYNTAX statement allows values for both -- the ANSI and ITU variants. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerMtp3T25 ::= Gauge(0|30000..35000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Timer at Signalling Point (SP) adjacent to restarting -- SP, waiting for traffic restart allowed message. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 30000 35000 30000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by the -- implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T26 ::= Gauge(0|12000..15000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Timer at restarting SP waiting to repeat traffic -- restart waiting message. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 12000 15000 12000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T27 ::= Gauge(0|2000..50000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Minimum duration of unavailability for full restart. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 2000 50000 4000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T28 ::= Gauge(0|3000..35000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Timer at SP adjacent to restarting SP waiting for -- traffic restart waiting message. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 3000 35000 30000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T29 ::= Gauge(0|60000..65000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Timer started when TRA sent in response to unexpected -- TRA or TRW. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 60000 65000 63000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T30 ::= Gauge(0|30000..35000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Timer to limit sending of TFPs and TFRs in response -- to unexpected TRA or TRW. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 30000 35000 33000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T31 ::= Gauge(0|10000..120000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- False link congestion detection timer. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 10000 120000 60000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T32 ::= Gauge(0|5000..120000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Link oscillation timer - Procedure A. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 5000 120000 60000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T33 ::= Gauge(0|60000..600000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Probation timer for link oscillation - Procedure B. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 60000 600000 300000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerMtp3T34 ::= Gauge(0|5000..120000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Suspension timer for link oscillation - Procedure B. -- Ranges by variant. -- -- Min Max Def -- ====== ====== ====== -- ANSI 5000 120000 60000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP) CItpTcTimerLinkTest ::= Gauge(0|4000..12000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Signalling Link test acknowledgement timer. -- -- Min Max Def -- ====== ====== ====== -- ANSI 4000 12000 8000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerLinkMessage ::= Gauge(0|30000..90000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Interval timer for sending test messages. -- -- Min Max Def -- ====== ====== ====== -- ANSI 30000 90000 60000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTimerLinkActRetry ::= Gauge(0|60000..90000) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- Link activation retry timer. -- -- Min Max Def -- ====== ====== ====== -- ANSI 60000 90000 60000 -- -- This timer is not used when the variant is ITU. -- A value of zero indicates a value is not defined -- for a particular variant or is not supported by -- the implementation. -- Refer -- ITU Q.704 Signalling network functions and messages. -- ANSI T1.111 Telecommunications - Signalling system -- No. 7 (SS7)-Message Transfer Part (MTP). CItpTcTranslationType ::= INTEGER { tt(1), ssn(2) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The Translation Type for SCCP GTT GTA specifies Title -- Translation or Subsystem Number (SSN) -- 'tt' : The GTT GTA has specified Title Translation -- 'ssn' : The GTT GTA has specified Subsystem Number. CItpTcURL ::= OCTET STRING(SIZE(0..255)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The URL used to load a configuration file. -- -- An octet string specified by an administrator that must -- be in human-readable form. The names must conform to -- the allowed characters that can be specified via -- Command Line Interface(CLI). The names cannot contain -- control character and should not contain leading or -- trailing white space. CItpTcXuaName ::= OCTET STRING(SIZE(0..12)) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- The configured name associated with M3UA/SUA -- ASP or AS name. -- -- An octet string specified by an administrator that -- must be in human-readable form. The names must -- conform to the allowed characters that can be -- specified via Command Line Interface(CLI). The -- names cannot contain control character and should -- not contain leading or trailing white space. END