-- MIB created 6/25/99 12:57:40, by
--   SMIC (the next generation) version 1.6.29, November 22, 1994.

CISCO-STUN-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-STUN-MIB.my"

IMPORTS
    Counter32, IpAddress
            FROM SNMPv2-SMI-v1
    OBJECT-TYPE
            FROM RFC-1212
    TRAP-TYPE
            FROM RFC-1215
    ifIndex, InterfaceIndex
            FROM IF-MIB
    TruthValue
            FROM SNMPv2-TC-v1
    ciscoMgmt
            FROM CISCO-SMI;

ciscoStunMIB OBJECT IDENTIFIER ::= { ciscoMgmt 30 }
-- MODULE-IDENTITY
--  LastUpdated
--    9508210000Z
--  OrgName
--    Cisco Systems, Inc.
--  ContactInfo
--     Cisco Systems
--     Customer Service
--                       
--    Postal: 170 W. Tasman Drive
--     San Jose, CA 95134
--     USA
--    
--       Tel: +1 800 553-NETS
--    e-mail: cs-snmp@cisco.com
--  Descr
--    The MIB module for serial Tunneling.
--    
--     Overview of STUN MIB
--    
--     MIB description
--     
--     The STUN MIB provides the configuration and operational information 
--     on Cisco's serial tunnelling implementation.  The following entities
--     are managed:
--      1) Global STUN information
--      2) STUN groups
--      3) STUN ports
--      4) STUN routes
--    
--     The following example configuration shows how the STUN MIB returns
--     STUN information, from either CISCO A or CISCO B.
--    
--      HOST == SDLC == Cisco A == IP Network == Cisco B == SDLC  == SDLC
--              line                                        line     device
--    
--     1) The STUN global entry identifies the IP address by which the
--        router is known to other STUN peers.
--     2) The STUN group table identifies the STUN group number and protocol
--        type that Cisco A and Cisco B use to route SDLC traffic over the 
--        IP network.  The table contains an entry for each STUN group
--        defined on the router.
--     3) The STUN port table identifies the serial interface to the SDLC 
--        line for which the router is doing serial tunnelling.  The MIB also
--        identifies the STUN group this interface is defined for, and
--        identifies the default routing for unrecognized SDLC addresses.
--        There is a port entry for each STUN-enabled interface on the router.
--     4) The STUN route table has an entry for each address defined for
--        routing within the STUN group, and an entry for the default routing
--        if the 'stun route all' command is configured.  The route entry
--        includes identification of the STUN peer, priority, state, whether
--        local acknowledgment is enabled, and packet and byte counters.
--     
--  RevDate
--    9508210000Z
--  RevDescr
--    Added revision clause, formatting cleanup.
--  RevDate
--    9503170000Z
--  RevDescr
--    Initial version of this MIB module.

stunObjects     OBJECT IDENTIFIER ::= { ciscoStunMIB 1 }
stunGlobal      OBJECT IDENTIFIER ::= { stunObjects 1 }
stunGroups      OBJECT IDENTIFIER ::= { stunObjects 2 }
stunPorts       OBJECT IDENTIFIER ::= { stunObjects 3 }
stunRoutes      OBJECT IDENTIFIER ::= { stunObjects 4 }
stunNotificationPrefix OBJECT IDENTIFIER ::= { ciscoStunMIB 2 }
stunNotifications OBJECT IDENTIFIER ::= { stunNotificationPrefix 0 }
stunMibConformance OBJECT IDENTIFIER ::= { ciscoStunMIB 3 }
stunMibCompliances OBJECT IDENTIFIER ::= { stunMibConformance 1 }
stunMibGroups   OBJECT IDENTIFIER ::= { stunMibConformance 2 }

stunIPAddr OBJECT-TYPE
    SYNTAX IpAddress
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The configured IP address used for all serial tunnelling
         in this router."
    ::= { stunGlobal 1 }

stunGroupTable OBJECT-TYPE
    SYNTAX SEQUENCE OF StunGroupEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A table of entries representing STUN groups configured on the
         router.  Each STUN-enabled interface is assigned to a STUN
         group, and packets can only travel between STUN-enabled
         interfaces in the same group."
    ::= { stunGroups 1 }

stunGroupEntry OBJECT-TYPE
    SYNTAX StunGroupEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Status and parameter values for a group."
    INDEX { stunGroupIndex }
    ::= { stunGroupTable 1 }

StunGroupEntry ::= SEQUENCE {
    stunGroupIndex INTEGER,
    stunProtocolType INTEGER
    }

stunGroupIndex OBJECT-TYPE
    SYNTAX INTEGER(1..255)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The configured STUN group number."
    ::= { stunGroupEntry 1 }

stunProtocolType OBJECT-TYPE
    SYNTAX INTEGER {
        basic(1),
        sdlc(2),
        sdlctg(3),
        custom(4)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The protocol type for this STUN group."
    ::= { stunGroupEntry 2 }

stunPortTable OBJECT-TYPE
    SYNTAX SEQUENCE OF StunPortEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A list of STUN-enabled interfaces (ports)."
    ::= { stunPorts 1 }

stunPortEntry OBJECT-TYPE
    SYNTAX StunPortEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Status and parameter values for a STUN port."
    INDEX { ifIndex }
    ::= { stunPortTable 1 }

StunPortEntry ::= SEQUENCE {
    stunPortGroupIndex INTEGER,
    stunPortDefaultPeerType INTEGER,
    stunPortDefaultPeerIP IpAddress,
    stunPortDefaultPeerSerialInterface InterfaceIndex
    }

stunPortGroupIndex OBJECT-TYPE
    SYNTAX INTEGER(1..255)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The group number to which the stun port
         belongs.  Frames will only be routed to other 
         ports (on this or another router) in the same 
         stun group.  This group must match a stunGroupIndex
         in the stunGroupTable."
    ::= { stunPortEntry 1 }

stunPortDefaultPeerType OBJECT-TYPE
    SYNTAX INTEGER {
        other(1),
        ip(2),
        direct(3),
        frameRelay(4)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The type of identification of the default partner 
         for unrecognized addresses. If there
         is no default route then the stunRouteType
         field of stunPortDefaultRemote is 'other'.
         If ip then the value is in stunRouteIP; if serial or
         serialDirect then the value is in stunRouteSerial."
    ::= { stunPortEntry 2 }

stunPortDefaultPeerIP OBJECT-TYPE
    SYNTAX IpAddress
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The ip address of the remote default STUN partner,
         for unrecognized addresses.  
         0.0.0.0 is returned if the default route type is not ip."
    ::= { stunPortEntry 3 }

stunPortDefaultPeerSerialInterface OBJECT-TYPE
    SYNTAX InterfaceIndex
--    Rsyntax Integer32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If stunRouteType is serial then this is the 
         serial interface index of the point-to-point
         link to the remote partner; 
         if stunRouteType is serialDirect then the 
         partner is in the local STUN.
         if stunRouteType is ip then this field is
         0."
    ::= { stunPortEntry 4 }

stunRouteTable OBJECT-TYPE
    SYNTAX SEQUENCE OF StunRouteEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A table containing information about specific SDLC
         addresses.  There is one table entry for each SDLC
         address configured by the STUN ROUTE command."
    ::= { stunRoutes 1 }

stunRouteEntry OBJECT-TYPE
    SYNTAX StunRouteEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The information regarding a single STUN address."
    INDEX { stunGroupIndex, stunRouteStationAddress }
    ::= { stunRouteTable 1 }

StunRouteEntry ::= SEQUENCE {
    stunRouteStationAddress INTEGER,
    stunRouteType INTEGER,
    stunRouteRemoteIP IpAddress,
    stunRouteSerialInterface InterfaceIndex,
    stunRoutePriority INTEGER,
    stunRoutePeerState INTEGER,
    stunRouteLocalAck TruthValue,
    stunRouteRxPackets Counter32,
    stunRouteTxPackets Counter32,
    stunRouteRxBytes Counter32,
    stunRouteTxBytes Counter32
    }

stunRouteStationAddress OBJECT-TYPE
    SYNTAX INTEGER(1..256)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The poll address of the station.  256 indicates the ALL parameter
         on the STUN ROUTE command, which is the route for all 
         unrecognized addresses."
    ::= { stunRouteEntry 1 }

stunRouteType OBJECT-TYPE
    SYNTAX INTEGER {
        other(1),
        ip(2),
        direct(3),
        frameRelay(4)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The type of identification of the remote partner."
    ::= { stunRouteEntry 2 }

stunRouteRemoteIP OBJECT-TYPE
    SYNTAX IpAddress
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The ip address of the remote STUN partner. 
         0.0.0.0 if partner type is not ip."
    ::= { stunRouteEntry 3 }

stunRouteSerialInterface OBJECT-TYPE
    SYNTAX InterfaceIndex
--    Rsyntax Integer32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The local interface index to the remote partner.
         0 is returned if the partner type is not direct or frameRelay."
    ::= { stunRouteEntry 4 }

stunRoutePriority OBJECT-TYPE
    SYNTAX INTEGER {
        low(1),
        normal(2),
        medium(3),
        high(4)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The priority with which this station's traffic will
         be routed across the network."
    ::= { stunRouteEntry 5 }

stunRoutePeerState OBJECT-TYPE
    SYNTAX INTEGER {
        dead(1),
        closed(2),
        opening(3),
        openWait(4),
        connected(5),
        direct(6)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The state of the peer connection through the
         STUN tunnel."
    ::= { stunRouteEntry 6 }

stunRouteLocalAck OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Indicates if the STUN connection is locally acknowledged.       
         TRUE-> STUN connection is locally acknowledged
         FALSE-> STUN connection is not locally acknowledged"
    ::= { stunRouteEntry 7 }

stunRouteRxPackets OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Count of frames received from the serial
         interface with this station's address."
    ::= { stunRouteEntry 8 }

stunRouteTxPackets OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Count of frames transmitted at the serial
         interface with this station's address."
    ::= { stunRouteEntry 9 }

stunRouteRxBytes OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Count of bytes received from the serial
         interface with this station's address."
    ::= { stunRouteEntry 10 }

stunRouteTxBytes OBJECT-TYPE
    SYNTAX Counter32
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Count of bytes transmitted at the serial
         interface with this station's address."
    ::= { stunRouteEntry 11 }

stunPeerStateChangeNotification TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE stunNotificationPrefix
    VARIABLES {
        stunRoutePeerState }
--  Status
--    mandatory
    DESCRIPTION
        "This notification indicates that the state of a STUN route
         has transitioned to active (connected or direct) or inactive
         (dead or closed)."
    ::= 1

stunGlobalGroup OBJECT IDENTIFIER ::= { stunMibGroups 1 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing global STUN information.
--  objects
--    stunIPAddr

stunGroupGroup OBJECT IDENTIFIER ::= { stunMibGroups 2 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing information about 
--     STUN groups .
--  objects
--    stunProtocolType

stunPortGroup OBJECT IDENTIFIER ::= { stunMibGroups 3 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing information about
--     STUN enabled interfaces.
--  objects
--    stunPortGroupIndex, stunPortDefaultPeerType, 
--    stunPortDefaultPeerIP, stunPortDefaultPeerSerialInterface

stunRouteGroup OBJECT IDENTIFIER ::= { stunMibGroups 4 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of objects providing information about
--     STUN defined routes.
--  objects
--    stunRouteType, stunRouteRemoteIP, stunRouteSerialInterface, 
--    stunRoutePriority, stunRoutePeerState, stunRouteLocalAck, 
--    stunRouteRxPackets, stunRouteTxPackets, stunRouteRxBytes, 
--    stunRouteTxBytes

stunMibCompliance OBJECT IDENTIFIER ::= { stunMibCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--    The compliance statement for STUN.
--  Module
--    >>current<<
--   MandGroup
--    stunGlobalGroup
--   MandGroup
--    stunGroupGroup
--   MandGroup
--    stunPortGroup
--   MandGroup
--    stunRouteGroup


END