-- MIB created 10/25/100 21:01:18, by
--   SMIC (the next generation) version 1.6.29, November 22, 1994.

CISCO-WIRELESS-TC-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-WIRELESS-TC-MIB.my"

IMPORTS
    Gauge32, Integer32,Counter32
            FROM SNMPv2-SMI-v1
    ciscoMgmt
            FROM CISCO-SMI;

ciscoWirelessTextualConventions OBJECT IDENTIFIER ::= { ciscoMgmt 137 }
-- MODULE-IDENTITY
--  LastUpdated
--    200004030000Z
--  OrgName
--    Cisco Systems, Inc.
--  ContactInfo
--           Cisco Systems
--     Customer Service
--    
--    Postal: 170 W Tasman Drive
--     San Jose, CA  95134
--     USA
--     Tel: +1 800 553-NETS
--     E-mail: wireless-nms@cisco.com
--  Descr
--    This module defines textual conventions used
--    in Cisco Wireless MIBs.
--  RevDate
--    200004030000Z
--  RevDescr
--    Added TEXTUAL-CONVENTIONs for
--        CwrRfType
--        CwrFixedPointScale
--        CwrFixedPointPrecison
--        CwrFixedPointValue
--        P2mpSnapshotAttribute
--        CwrPercentageValue
--        CwrRfFreqRange
--        CwrUpdateTime
--     Modified P2mpRadioSignalAttribute

CwrRFZeroIndex ::= INTEGER(0..2)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This represents an index into the cwrRFTable. The valid values 
--    are from 1 onwards. The special value of 0 is used to indicate 
--    the absence of the associated RF resource.

CwrCwErrorFreeSecond ::= Gauge32
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A Codeword Error Free Second (EFS) is defined as 1 second when 
--    the radio link was synchronized and no codeword errors detected 
--    on the link.

CwrCwErroredSecond ::= Gauge32
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A Codeword Errored Second (ES) is defined as 1 second when the 
--    radio link was synchronized and 1 or more codeword errors were 
--    detected on the link.

CwrCwSeverelyErroredSecond ::= Gauge32
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A Codeword Severely Errored Second (SES) is defined as 1 
--    second when the radio link was synchronized and the codeword 
--    error rate (CER) was greater than the threshold specified by 
--    cwrLinkHighCwErrThresh.

CwrCwConsecutiveSevErrSecond ::= Gauge32
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A Codeword Consecutively Severely Errored Seconds (CSES) is 
--    defined as the metric that measures the number of times a 
--    sequence of Codeword Severely Errored Seconds(SES) crosses the 
--    cwrLinkCSESThresh value.  It is independent of the length of 
--    the SES sequence.  In other words this counter is incremented by
--    one and only one for every such occurrence.

CwrCwDegradedSecond ::= Gauge32
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A Codeword Degraded Second (DS) is defined as a 1 second 
--    interval during which the CER was between cwrLinkLowCwErrThresh
--    and cwrLinkHighCwErrThresh.

CwrCwDegradedMinute ::= Gauge32
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A Codeword Degraded Minute (DM) is defined as a 60 Codeword 
--    Degraded Seconds.

CwrCollectionAction ::= INTEGER {
        actionStop(1),
        actionStart(2),
        actionClear(3),
        actionRestart(4)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    The action to perform on the identified specification.
--    It can be:
--    Stop: Stop the collection specification from continuing.
--    Start: Start the collection specification.
--    Clear: Clear the current collection data. A collection in 
--    progress must be stopped before it can be cleared.
--    Restart: Identical to Clear followed by a Start.

CwrCollectionStatus ::= INTEGER {
        statusIdle(1),
        statusInProgress(2),
        statusStopped(3),
        statusCaptured(4)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This indicates the current status of the collection 
--    specification. It can be:
--    Idle: No action in progress.
--    In_progress: Collection specification is currently being 
--                 executed
--    Stopped: The collection specification has been stopped before
--    it completed successfully.
--    Captured: The collection is complete and data is available.

CwrdBm ::= INTEGER(-80..33)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This is a unit of power measurement. It is measured in decibels
--    of milliwatts (dBm). dBm = 10 * log(millwatts of power).

CwrdB ::= INTEGER(0..16)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This is a unit of measurement defined as decibels (dB).
--    dB = 10 * log(measured_value).

CwrThreshLimitType ::= INTEGER {
        upChange(1),
        downChange(2),
        highThresh(3),
        lowThresh(4),
        upLimit(5),
        lowLimit(6)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This object represents the kind of change that needs to be 
--           monitored for a thresholdable attribute . An event is generated 
--           when the following condition is met.
--    The kinds of change that may be setup in the radio hardware are:
--    
--    upChange   : Monitored value changes by a positive amount.
--    downChange : Monitored value changes by a negative amount.
--    highThresh : Monitored value exceeds specified threshold.
--    lowThresh  : Monitored value receeds below a threshold.
--    upLimit    : Monitored value crosses the specified threshold 
--                        when increasing in value.
--    lowLimit   : Monitored value crosses the specified threshold 
--          when decreasing in value.

CwrRadioSignalAttribute ::= INTEGER {
        rsaIN(1),
        rsaINR(2),
        rsaConstellationVariance(3),
        rsaTimingOffset(4),
        rsaReceivedPower(5),
        rsaGainSettingsIF(6),
        rsaGainSettingsRF(7),
        rsaFreqOffset(8),
        rsaTotalGain(9),
        rsaSyncStatus(10)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This represents the set of radio signal attributes that may be
--    monitored by using histograms, timelines, and thresholds.
--    
--    The  attributes are:
--    
--    rsaIN(1) -
--     This is the Interference + Noise power levels computed 
--     by the hardware on a burst by burst basis. This is 
--                   available for a dual antenna system only.
--          
--    rsaINR(2) -
--     This is the ratio of the interference+noise power levels
--     captured by first antenna to that captured by the second
--     antenna on a burst by burst basis.
--     The values reported are in log to base 2.
--    
--           rsaConstellationVariance(3) - 
--     Constellation variance(CV) is the average energy of the
--     constellation error signal. The constellation error
--     signal is the error between the received (noisy) 
--                   constellation symbol and the nearest ideal constellation
--                   symbol.  CV is a measure of the Signal to 
--                   Interference+noise ratio, (SINR) for that tone.
--     On a Single antenna system it represents (1/SINR).
--     On a Dual antenna system it represents a 
--     composite histogram providing (1/SINR).
--       
--    rsaTimingOffset(4) -
--     This represents the histogram of timing delay variations
--     detected in radio link.
--            
--    rsaReceivedPower(5) -
--     This is a measure of the analog signal power received
--      by the radio system on a burst by burst basis.
--    
--           rsaGainSettingsIF(6) -
--     This represents the change in the automatic gain control
--     loop maintained by the hardware. This may be captured
--     for each antenna and at the intermediate frequency (IF)
--     module.
--     Units: Integral values
--            
--    rsaGainSettingsRF(7) -
--     This represents the change in the automatic gain control
--     loop maintained by the hardware. This may be
--     captured for each antenna and at both the intermediate
--     frequency (IF) and radio frequency (RF) modules.
--     Units: Integral values
--            
--    rsaFreqOffset(8) -
--     This represents the frequency offset calculations
--     made to keep the receive frequency on a slave radio in
--     sync with the master radio.
--     Units: Integral values.
--    
--           rsaTotalGain(9) -
--     This represents the change in the automatic gain control
--     loop maintained by the hardware. This may be
--     captured for each antenna.
--     Units: Integral values
--    
--    rsaSyncStatus(10) -
--     This represents the sync status.

CwrOscState ::= INTEGER {
        oscillatorOk(1),
        osccillatorBad(2)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    The current state of the oscillator.

P2mpRadioSignalAttribute ::= INTEGER {
--        none(0),
        rsaSinrMainAnt(1),
        rsaSinrDiversityAnt(2),
        rsaSinrRatio(3),
        rsaTimingOffset(4),
        rsaRxPowerMainAnt(5),
        rsaRxPowerDiversityAnt(6),
        rsaChDelaySpreadMainAnt(7),
        rsaChDelaySpreadDiversityAnt(8),
        rsaHeAmbientNoise(9),
        rsaSuRxPowerDeltaMainAnt(10),
        rsaSuRxPowerDeltaDiversityAnt(11),
        rsaSuTotalTxPower(12)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This represents the set of radio signal attributes that may be
--    monitored in a point to multipoint system by using histograms, 
--    timelines, and thresholds.  Some of these attributes are common 
--    to the head end (HE) and the subscriber unit (SU) whereas some 
--    are specific to either the HE or the SU.
--    
--    The  attributes are:
--    
--    none(0) -
--           This is a special value reserved to indicate that there 
--           is no threshold associated with a timeline.  This 
--           attribute cannot be used to create a histogram, timeline,
--           or threshold.
--    
--    rsaSinrMainAnt(1) -
--            This is the Interference + Noise power level computed by
--            the hardware at the main antenna on a burst by burst  
--            basis
--    
--    rsaSinrDiversityAnt(2) -
--            This is the Interference + Noise power level computed by
--            the hardware at the diversity antenna on a burst by 
--            burst basis.
--    
--    rsaSinrRatio(3) -
--            Ratio of (Interference + Noise) in main antenna to 
--            diversity antenna 
--    
--    rsaTimingOffset(4) -
--            This represents the timing delay variations detected on 
--            a radio link.
--    
--    rsaRxPowerMainAnt(5) -
--            This is a measure of the analog signal power received at 
--            the main antenna RF head on a burst by burst basis.
--    
--    rsaRxPowerDiversityAnt(6) -
--            This is a measure of the analog signal power received at 
--            the diversity antenna RF head on a burst by burst basis.
--    
--    rsaChDelaySpreadMainAnt(7) -
--            Number of samples that the channel response remains 
--            within (TBD) db of the manimun TAP in the channel 
--            response at the main antenna.
--    
--    rsaChDelaySpreadDiversityAnt(8) -
--            Number of samples that the channel response remains 
--            within (TBD) db of the manimun TAP in the channel 
--            response at the diversity antenna.
--    
--    rsaHeAmbientNoise(19) -
--            The ambient noise (in dB) is measured when there is no 
--            signal being received at the Headend
--    
--    rsaSuRxPowerDeltaMainAnt(10) -
--            Change in received power (dB) at the main antenna of the
--            subscriber unit on a burst by burst basis.
--    
--    rsaSuRxPowerDeltaDiversityAnt(11) -
--            Change in received power (dB) at the diversity antenna 
--            of the subscriber unit on a burst by burst basis.
--    
--    rsaSuTotalTxPower(12) - 
--            The sum of -20 dBm (reference level out of the DAC) +
--            Tx IF transmit gain - 13 dBm (cable compensation) + Tx 
--            RF transmit gain.  This parameter does not include 
--            antenna gains.  

CwrRfType ::= INTEGER {
--        main(0),
        diversity(1)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    Indicates if the outdoor RF unit is being used as the main RF 
--    unit or the diversity RF unit.  The main RF unit is used to 
--    receive and transmit data whereas the diversity unit is used to 
--    receive only.

CwrFixedPointScale ::= INTEGER {
        yocto(1),
        zepto(2),
        atto(3),
        femto(4),
        pico(5),
        nano(6),
        micro(7),
        milli(8),
        units(9),
        kilo(10),
        mega(11),
        giga(12),
        tera(13),
        exa(14),
        peta(15),
        zetta(16),
        yotta(17)
        }
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    International System of Units (SI) prefixes.

CwrFixedPointPrecision ::= Integer32(0..9)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    When in the range 1 to 9, CwrFixedPointPrecision is the number
--    of decimal places in the fractional part of a fixed-point
--    number.
--    
--    CwrFixedPointPrecision is 0 for non-fixed-point numbers.

CwrFixedPointValue ::= INTEGER(-2147483648..2147483647)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This represents a fixed point number. Use values -2147483648
--    and +2147483647 to indicate underflow and overflow 
--    respectively. Use CwrFixedPointPrecision to indicate how 
--    many fractional digits the CwrFixedPointValue has.

P2mpSnapshotAttribute ::= OCTET STRING(SIZE(1))
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This represents the set of radio signal attributes that may be
--    monitored by using a snapshot.  The user can capture upto 4 
--    radio signal attributes simultaneously, by picking at most one
--    signal from each of the sets below and setting the bit
--    corresponding to each selected signal.
--    
--    When a snapshot request is issued up to four radio signal 
--    attributes may be requested at once, one from each set:
--    ===============================================
--    Type   Set1               Set2
--    ===============================================
--    RX     y1n(x1)            y2n(x2)
--           H2k(x80)           H1k(x40)
--    ===============================================
--    
--    ===============================================
--    Type   Set3                Set4
--    ===============================================
--    RX     Y2k(x8)             Y1k(x4)
--           h1n(x10)            h2n(x20)
--           zhat(x100)          -
--    ===============================================
--    
--    The attributes are:
--    
--    rxRawBurstAnt1Y1n(0) -
--            This represents a snapshot of the received signal for 
--            the main RF resource. For every sample, the real and 
--            imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxRawBurstAnt2Y2n(1) -
--            This represents a snapshot of the received signal for 
--            the diversity RF resource. For every sample, the real 
--            and imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxSpectrumAnt1Y1k(2) -
--            This represents a snapshot of the spectrum of the 
--            received signal for the main RF resource. For every 
--            sample, the real and imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxSpectrumAnt2Y2k(3) -
--            This represents a snapshot of the spectrum of the 
--            received signal for the diversity RF resource. For every
--            sample the real and imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxTimeDomainChannelAnt1H1n(4) -
--            This represents a snapshot of the time domain channel
--            for the main RF resource. For every sample the real and
--            imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxTimeDomainChannelAnt2H2n(5) -
--            This represents a snapshot of the time domain channel
--            for the diversity RF resource. For every sample, the 
--            real and imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxFreqDomainChannelAnt1H1k(6) -
--            This represents a snapshot of the frequency domain 
--            channel for the main RF resource. For every sample the 
--            real and imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxFreqDomainChannelAnt2H2k(7) -
--            This represents a snapshot of the frequency domain 
--            channel for the diversity RF resource. For every sample,
--            the real and imaginary components are captured.
--            Units: (I, q)
--            Value: 32 bit quantities.
--    
--    rxConstellationZHatk(8) -
--            This represents a snapshot of the soft decisions.
--            For every sample, the real and imaginary components are 
--            captured.
--            Units: (I, q)
--            Value: 32 bit quantities.

CwrPercentageValue ::= Gauge32(0..10000000)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This object can be used to represent percentage values for 
--    codeword errors, available seconds, etc. The UNITS clause 
--    associated with each object will indicate the degree of 
--    precison.

CwrUpdateTime ::= Integer32(0..2147483647)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This is used to report statistics values measured on the 
--    wireless link with a 1 second granularity insted of timeTicks. 

CwrRfFreqRange ::= Integer32(0..60000000)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This represents the entire radio frequency range for a wireless
--    radio product.  The lower limit is assumed to be zero.

WirelessGauge64 ::= Counter32
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    This is a temporary textual convention that will be deleted
--    from this MIB when all references to this TC have been changed
--    to use 'CounterBasedGauge64' defined in RFC 2856


END