-- MIB file created 23-Jan-2002 14:26:08, by
--   SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com

MPLS-TE-MIB DEFINITIONS ::= BEGIN

-- From file: "MPLS-TE-MIB.my"
-- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T"

IMPORTS
    experimental
            FROM SNMPv2-SMI-v1
    TruthValue, RowStatus, RowPointer, StorageType, DisplayString, 
    TimeStamp
            FROM SNMPv2-TC-v1
    InterfaceIndexOrZero
            FROM IF-MIB
    MplsBitRate, MplsBurstSize, MplsLSPID
            FROM MPLS-LSR-MIB
    InetAddressIPv4, InetAddressIPv6
            FROM INET-ADDRESS-MIB
    Counter, Gauge, TimeTicks
            FROM RFC1155-SMI
    OBJECT-TYPE
            FROM RFC-1212
    TRAP-TYPE
            FROM RFC-1215;

mplsTeMIB OBJECT IDENTIFIER ::= { experimental 95 }
-- MODULE-IDENTITY
--  LastUpdated
--    200011211200Z
--  OrgName
--    Multiprotocol Label Switching (MPLS) Working Group
--  ContactInfo
--            Cheenu Srinivasan
--     Postal: Tachion Networks, Inc.
--           Monmouth Park Corporate Center I
--           Building C, 185 Monmouth Park Highway
--           West Long Branch, NJ 07764
--     Tel:    +1-732-542-7750 x1234
--     Email:  cheenu@tachion.com
--    
--             Arun Viswanathan
--     Postal: Force10 Networks, Inc.
--             1440 McCarthy Blvd
--             Milpitas, CA 95035
--     Tel:    +1-408-571-3516
--     Email:  arun@force10networks.com
--    
--           Thomas D. Nadeau
--    Postal: Cisco Systems, Inc.
--           250 Apollo Drive
--           Chelmsford, MA 01824
--    Tel:    +1-978-244-3051
--     Email:  tnadeau@cisco.com
--  Descr
--    This MIB module contains managed object
--     definitions for MPLS Traffic Engineering (TE) as
--     defined in: Extensions to RSVP for LSP Tunnels,
--     Awduche et al, Internet Draft <draft-ietf-mpls-
--     rsvp-lsp-tunnel-07.txt>, August 2000; Constraint-
--     Based LSP Setup using LDP, B. Jamoussi, Internet
--     Draft <draft-ietf-mpls-cr-ldp-04.txt>, July 2000;
--     Requirements for Traffic Engineering Over MPLS,
--     Awduche, D., J. Malcolm, J., Agogbua, J., O'Dell,
--     M., J. McManus, <rfc2702.txt>, September 1999.
--  RevDate
--    200011211200Z
--  RevDescr
--    Updates based on MPLS WG feedback
--  RevDate
--    200007141200Z
--  RevDescr
--    Updates based on MPLS WG feedback
--  RevDate
--    200005261200Z
--  RevDescr
--    Updates based on MPLS WG feedback
--  RevDate
--    200003031200Z
--  RevDescr
--    Updates based on MPLS WG feedback
--  RevDate
--    199907161200Z
--  RevDescr
--    Initial draft version.

mplsTeScalars   OBJECT IDENTIFIER ::= { mplsTeMIB 1 }
mplsTeObjects   OBJECT IDENTIFIER ::= { mplsTeMIB 2 }
mplsTeNotifications OBJECT IDENTIFIER ::= { mplsTeMIB 3 }
mplsTeNotifyPrefix OBJECT IDENTIFIER ::= { mplsTeNotifications 0 }
mplsTeConformance OBJECT IDENTIFIER ::= { mplsTeMIB 4 }
mplsTeGroups    OBJECT IDENTIFIER ::= { mplsTeConformance 1 }
mplsTeCompliances OBJECT IDENTIFIER ::= { mplsTeConformance 2 }

MplsTunnelIndex ::= INTEGER(1..65535)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    Index into mplsTunnelTable.

MplsTunnelInstanceIndex ::= Gauge(0..65535)
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    Instance index into mplsTunnelTable.

MplsLsrId ::= Gauge
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A unique identifier for an MPLS LSR. This MAY
--     represent an IpV4 address.

MplsPathIndex ::= Gauge
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A unique identifier used to identify a specific
--     path used by a tunnel.

MplsPathIndexOrZero ::= Gauge
-- TEXTUAL-CONVENTION
--  Status
--    mandatory
--  Descr
--    A unique identifier used to identify a specific
--     path used by a tunnel. If this value is set to 0,
--     it indicates that no path is in use.

mplsTunnelConfigured OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of tunnels configured on this device. A
         tunnel is considered configured if the
         mplsTunnelRowStatus is active(1)."
    ::= { mplsTeScalars 1 }

mplsTunnelActive OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The number of tunnels active on this device. A
         tunnel is considered active if the
         mplsTunnelOperStatus is up(1)."
    ::= { mplsTeScalars 2 }

mplsTunnelTEDistProto OBJECT-TYPE
    SYNTAX OCTET STRING(SIZE(1..2))
        -- BITS are:
        --   other(0)
        --   ospf(1)
        --   isis(2)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The traffic engineering distribution protocol(s)
         used by this LSR. Note that an LSR may support
         more than one distribution protocols
         simultaneously."
    ::= { mplsTeScalars 3 }

mplsTunnelMaxHops OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The maximum number of hops that can be specified
         for a tunnel on this device."
    ::= { mplsTeScalars 4 }

mplsTunnelIndexNext OBJECT-TYPE
    SYNTAX INTEGER(0..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object contains the next appropriate value to
         be used for mplsTunnelIndex when creating entries
         in  mplsTunnelTable. If the number of unassigned
         entries is exhausted, a retrival operation will
         return a value of 0.  This object may also return
         a value of 0 when the LSR is unable to accept
         conceptual row creation, for example, if the
         mplsTunnelTable is implemented as read-only. To
         obtain the value of mplsTunnelIndex for a new
         entry, the manager must first issue a management
         protocol retrieval operation to obtain the current
         value of this object. The agent should modify the
         value to reflect the next unassigned index after
         each retrieval operation. After a manager
         retrieves a value the agent will determine through
         its local policy when this index value will be
         made available for reuse."
    ::= { mplsTeObjects 1 }

mplsTunnelTable OBJECT-TYPE
    SYNTAX SEQUENCE OF MplsTunnelEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The mplsTunnelTable allows new MPLS tunnels to be
         created between an LSR and a remote endpoint, and
         existing tunnels to be reconfigured or removed.
         Note that only point-to-point tunnel segments are
         supported, although multi-point-to-point and point-
         to-multi-point connections are supported by an LSR
         acting as a cross-connect.  Each MPLS tunnel can
         thus have one out-segment originating at this LSR
         and/or one in-segment terminating at this LSR."
    ::= { mplsTeObjects 2 }

mplsTunnelEntry OBJECT-TYPE
    SYNTAX MplsTunnelEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry in this table represents an MPLS tunnel.
         An entry can be created by a network administrator
         or by an SNMP agent as instructed by an MPLS
         signaling protocol. Whenever a new entry is
         created with mplsTunnelIsIf set to true(1), then a
         corresponding entry is created in ifTable as well
         (see RFC 2233). The ifType of this entry is
         mplsTunnel(150)."
    REFERENCE
        "1. RFC 2233 - The Interfaces Group MIB using
         SMIv2, McCloghrie, K., and F. Kastenholtz, Nov.
         1997
         2. RFC 1700 - Assigned Numbers, Reynolds, J. and
         J. Postel, Oct. 1994"
    INDEX { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId }
    ::= { mplsTunnelTable 1 }

MplsTunnelEntry ::= SEQUENCE {
    mplsTunnelIndex MplsTunnelIndex,
    mplsTunnelInstance MplsTunnelInstanceIndex,
    mplsTunnelIngressLSRId MplsLsrId,
    mplsTunnelEgressLSRId MplsLsrId,
    mplsTunnelName DisplayString,
    mplsTunnelDescr DisplayString,
    mplsTunnelIsIf TruthValue,
    mplsTunnelIfIndex InterfaceIndexOrZero,
    mplsTunnelXCPointer RowPointer,
    mplsTunnelSignallingProto INTEGER,
    mplsTunnelSetupPrio INTEGER,
    mplsTunnelHoldingPrio INTEGER,
    mplsTunnelSessionAttributes OCTET STRING,
    mplsTunnelOwner INTEGER,
    mplsTunnelLocalProtectInUse TruthValue,
    mplsTunnelResourcePointer RowPointer,
    mplsTunnelInstancePriority Gauge,
    mplsTunnelHopTableIndex MplsPathIndexOrZero,
    mplsTunnelARHopTableIndex MplsPathIndexOrZero,
    mplsTunnelCHopTableIndex MplsPathIndexOrZero,
    mplsTunnelPrimaryInstance MplsTunnelInstanceIndex,
    mplsTunnelPrimaryTimeUp TimeTicks,
    mplsTunnelPathChanges Counter,
    mplsTunnelLastPathChange TimeTicks,
    mplsTunnelCreationTime TimeStamp,
    mplsTunnelStateTransitions Counter,
    mplsTunnelIncludeAnyAffinity Gauge,
    mplsTunnelIncludeAllAffinity Gauge,
    mplsTunnelExcludeAllAffinity Gauge,
    mplsTunnelPathInUse MplsPathIndexOrZero,
    mplsTunnelRole INTEGER,
    mplsTunnelTotalUpTime TimeTicks,
    mplsTunnelInstanceUpTime TimeTicks,
    mplsTunnelAdminStatus INTEGER,
    mplsTunnelOperStatus INTEGER,
    mplsTunnelRowStatus RowStatus,
    mplsTunnelStorageType StorageType
    }

mplsTunnelIndex OBJECT-TYPE
    SYNTAX MplsTunnelIndex
--    Rsyntax INTEGER(1..65535)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Uniquely identifies this row."
    ::= { mplsTunnelEntry 1 }

mplsTunnelInstance OBJECT-TYPE
    SYNTAX MplsTunnelInstanceIndex
--    Rsyntax Gauge(0..65535)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Uniquely identifies an instance of a tunnel. It is
         useful to identify multiple instances of tunnels
         for the purposes of backup and parallel tunnels."
    ::= { mplsTunnelEntry 2 }

mplsTunnelIngressLSRId OBJECT-TYPE
    SYNTAX MplsLsrId
--    Rsyntax Gauge
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The purpose of this object is to uniquely identity
         a tunnel within a network. When the MPLS
         signalling protoocol is rsvp(2) this value should
         mimic the Extended Tunnel Id field in the Session
         object. When the MPLS signalling protoocol is
         crldp(3) this value should mimic the Ingress LSR
         Router ID field in the LSPID TLV object."
    REFERENCE
        "1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
         Awduche et al, Internet Draft <draft-ietf-mpls-
         rsvp-lsp-tunnel-07.txt>, August 2000.,
         2. Constraint-Based LSP Setup using LDP, Jamoussi,
         Internet Draft <draft-ietf-mpls-cr-ldp-04.txt>,
         July 2000."
    ::= { mplsTunnelEntry 3 }

mplsTunnelEgressLSRId OBJECT-TYPE
    SYNTAX MplsLsrId
--    Rsyntax Gauge
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Specifies the egress LSR Id."
    ::= { mplsTunnelEntry 4 }

mplsTunnelName OBJECT-TYPE
    SYNTAX DisplayString
--    Rsyntax OCTET STRING(SIZE(0..255))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The canonical name assigned to the tunnel. This
         name can be used to refer to the tunnel on the
         LSR’s console port.  If mplsTunnelIsIf is set to
         true then the ifName of the interface
         corresponding to this tunnel should have a value
         equal to mplsTunnelName.  Also see the description
         of ifName in RFC 2233."
    REFERENCE
        "RFC 2233 - The Interfaces Group MIB using SMIv2,
         McCloghrie, K., and F. Kastenholtz, Nov. 1997"
    ::= { mplsTunnelEntry 5 }

mplsTunnelDescr OBJECT-TYPE
    SYNTAX DisplayString
--    Rsyntax OCTET STRING(SIZE(0..255))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "A textual string containing information about the
         tunnel.  If there is no description this object
         contains a zero length string."
    ::= { mplsTunnelEntry 6 }

mplsTunnelIsIf OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Denotes whether or not this tunnel corresponds to
         an interface represented in the interfaces group
         table. Note that if this variable is set to true
         then the ifName of the interface corresponding to
         this tunnel should have a value equal to
         mplsTunnelName.  Also see the description of
         ifName in RFC 2233."
    REFERENCE
        "RFC 2233 - The Interfaces Group MIB using SMIv2,
         McCloghrie, K., and F. Kastenholtz, Nov. 1997"
    DEFVAL { false }
    ::= { mplsTunnelEntry 7 }

mplsTunnelIfIndex OBJECT-TYPE
    SYNTAX InterfaceIndexOrZero
--    Rsyntax INTEGER(0..2147483647)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelIsIf is set to true, then this value
         contains the LSR-assigned ifIndex which
         corresponds to an entry in the interfaces table.
         Otherwise this variable should contain the value
         of zero indicating that a valid ifIndex was not
         assigned to this tunnel interface."
    REFERENCE
        "RFC 2233 - The Interfaces Group MIB using SMIv2,
         McCloghrie, K., and F. Kastenholtz, Nov. 1997"
    ::= { mplsTunnelEntry 8 }

mplsTunnelXCPointer OBJECT-TYPE
    SYNTAX RowPointer
--    Rsyntax OBJECT IDENTIFIER
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable points to a row in the mplsXCTable.
         This table identifies the segments that compose
         this tunnel, their characteristics, and
         relationships to each other. A value of
         zeroDotZero indicates that no LSP has been
         associated with this tunnel yet."
    REFERENCE
        "Srinivasan, C., Viswanathan, A., and T. Nadeau,
         MPLS Label Switch Router Management Information
         Base Using SMIv2, Internet Draft <draft-ietf-mpls-
         lsr-mib-06.txt>, July 2000."
    ::= { mplsTunnelEntry 9 }

mplsTunnelSignallingProto OBJECT-TYPE
    SYNTAX INTEGER {
        none(1),
        rsvp(2),
        crldp(3),
        other(4)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The signaling protocol, if any, which was used to
         setup this tunnel."
    DEFVAL { none }
    ::= { mplsTunnelEntry 10 }

mplsTunnelSetupPrio OBJECT-TYPE
    SYNTAX INTEGER(0..7)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Indicates the setup priority of this tunnel."
    REFERENCE
        "1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
         Awduche et al, Internet Draft <draft-ietf-mpls-
         rsvp-lsp-tunnel-07.txt>, August 2000.,
         2. Constraint-Based LSP Setup using LDP, Jamoussi,
         Internet Draft <draft-ietf-mpls-cr-ldp-04.txt>,
         July 2000."
    ::= { mplsTunnelEntry 11 }

mplsTunnelHoldingPrio OBJECT-TYPE
    SYNTAX INTEGER(0..7)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Indicates the holding priority for this tunnel."
    REFERENCE
        "1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
         Awduche et al, Internet Draft <draft-ietf-mpls-
         rsvp-lsp-tunnel-07.txt>, August 2000.,
         2. Constraint-Based LSP Setup using LDP, Jamoussi,
         Internet Draft <draft-ietf-mpls-cr-ldp-04.txt>,
         July 2000."
    ::= { mplsTunnelEntry 12 }

mplsTunnelSessionAttributes OBJECT-TYPE
    SYNTAX OCTET STRING(SIZE(1..2))
        -- BITS are:
        --   fastReroute(0)
        --   mergingPermitted(1)
        --   isPersistent(2)
        --   isPinned(3)
        --   isComputed(4)
        --   recordRoute(5)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This bitmask indicates optional session values for
         this tunnel. The following describes these
         bitfields:
        
        fastRerouteThis flag indicates that the any tunnel
         hop may choose to reroute this tunnel without
         tearing it down.
        This flag permits transit routers to use a local
         repair mechanism which may result in violation of
         the explicit routing of this tunnel. When a fault
         is detected on an adjacent downstream link or
         node, a transit router can reroute traffic for
         fast service restoration.
        
        mergingPermitted This flag permits transit routers
         to merge this session with other RSVP sessions for
         the purpose of reducing resource overhead on
         downstream transit routers, thereby providing
         better network scalability.
        
        isPersistent  Indicates whether this tunnel should
         be restored automatically after a failure occurs.
        
        isPinned   This flag indicates whether the loose-
         routed hops of this tunnel are to be pinned.
        
        isComputed This flag indicates whether the tunnel
         path is computed using a constraint-based routing
         algorithm based on the mplsTunnelHopTable entries.
        
        recordRoute               This flag indicates
         whether or not the signaling protocol should
         remember the tunnel path after it has been
         signaled."
    REFERENCE
        "1. RSVP-TE: Extensions to RSVP for LSP Tunnels,
         Awduche et al, Internet Draft <draft-ietf-mpls-
         rsvp-lsp-tunnel-07.txt>, August 2000."
    ::= { mplsTunnelEntry 13 }

mplsTunnelOwner OBJECT-TYPE
    SYNTAX INTEGER {
        admin(1),
        rsvp(2),
        crldp(3),
        policyAgent(4),
        other(5)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Indicates which protocol created and is
         responsible for managing this tunnel. Values
         rsvp(2) and crldp(3) should not be used at the
         head-end of a MPLS tunnel."
    ::= { mplsTunnelEntry 14 }

mplsTunnelLocalProtectInUse OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Indicates that the local repair mechanism is in
         use to maintain this tunnel (usually in the face
         of an outage of the link it was previously routed
         over)."
    ::= { mplsTunnelEntry 15 }

mplsTunnelResourcePointer OBJECT-TYPE
    SYNTAX RowPointer
--    Rsyntax OBJECT IDENTIFIER
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable represents a pointer to the traffic
         parameter specification for this tunnel.  This
         value may point at an entry in the
         mplsTunnelResourceEntry to indicate which
         mplsTunnelResourceEntry is to be assigned to this
         segment.  This value may optionally point at an
         externally defined traffic parameter specification
         table.  A value of zeroDotZero indicates best-
         effort treatment.  By having the same value of
         this object, two or more segments can indicate
        
        
         resource sharing."
    ::= { mplsTunnelEntry 16 }

mplsTunnelInstancePriority OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This value indicates which priority, in descending
         order, with 0 indicating the lowest priority,
         within a group of tunnel instances. A group of
         tunnel instances is defined as a set of tunnels
         with the same mplsTunnelIndex in this table, but
         with a different mplsTunnelInstance. Tunnel group
         priorities are used to denote the priority at
         which a particular tunnel instance will supercede
         another. Instances of tunnels containing the same
         mplsTunnelInstancePriority will be used for load
         sharing."
    DEFVAL { 0 }
    ::= { mplsTunnelEntry 17 }

mplsTunnelHopTableIndex OBJECT-TYPE
    SYNTAX MplsPathIndexOrZero
--    Rsyntax Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Index into the mplsTunnelHopTable entry that
         specifies the explicit route hops for this
         tunnel."
    ::= { mplsTunnelEntry 18 }

mplsTunnelARHopTableIndex OBJECT-TYPE
    SYNTAX MplsPathIndexOrZero
--    Rsyntax Gauge
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Index into the mplsTunnelARHopTable entry that
         specifies the actual hops traversed by the
         tunnel."
    ::= { mplsTunnelEntry 19 }

mplsTunnelCHopTableIndex OBJECT-TYPE
    SYNTAX MplsPathIndexOrZero
--    Rsyntax Gauge
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Index into the mplsTunnelCHopTable entry that
         specifies the computed hops traversed by the
         tunnel."
    ::= { mplsTunnelEntry 20 }

mplsTunnelPrimaryInstance OBJECT-TYPE
    SYNTAX MplsTunnelInstanceIndex
--    Rsyntax Gauge(0..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Specifies the instance index of the primary
         instance of this tunnel."
    ::= { mplsTunnelEntry 21 }

mplsTunnelPrimaryTimeUp OBJECT-TYPE
    SYNTAX TimeTicks
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Specifies the total time the primary instance of
         this tunnel has been active. The primary instance
         of this tunnel is defined in
         mplsTunnelPrimaryInstance."
    ::= { mplsTunnelEntry 22 }

mplsTunnelPathChanges OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Specifies the number of times the paths has
         changed for this tunnel."
    ::= { mplsTunnelEntry 23 }

mplsTunnelLastPathChange OBJECT-TYPE
    SYNTAX TimeTicks
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Specifies the time since the last path change for
         this tunnel."
    ::= { mplsTunnelEntry 24 }

mplsTunnelCreationTime OBJECT-TYPE
    SYNTAX TimeStamp
--    Rsyntax TimeTicks
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Specifies the value of SysUpTime when the first
         instance of this tunnel came into existence."
    ::= { mplsTunnelEntry 25 }

mplsTunnelStateTransitions OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Specifies the number of times the state of this
         tunnel instance has changed."
    ::= { mplsTunnelEntry 26 }

mplsTunnelIncludeAnyAffinity OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "A link satisfies the include-any constraint if and
         only if the constraint is zero, or the link and
         the constraint have a resource class in common."
    REFERENCE
        "RSVP-TE: Extensions to RSVP for LSP
        Tunnels,
         draft-ietf-mpls-rsvp-lsp-tunnel-07.txt"
    ::= { mplsTunnelEntry 27 }

mplsTunnelIncludeAllAffinity OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "A link satisfies the include-all constraint if and
         only if the link contains all of the adminstrative
         groups specified in the constraint."
    REFERENCE
        "RSVP-TE: Extensions to RSVP for LSP
        Tunnels, draft-ietf-mpls-rsvp-lsp-tunnel-07.txt"
    ::= { mplsTunnelEntry 28 }

mplsTunnelExcludeAllAffinity OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "A link satisfies the exclude-all constraint if and
         only if the link contains none of the
         adminstrative groups specifie in the constraint."
    REFERENCE
        "RSVP-TE: Extensions to RSVP for LSP
        Tunnels, draft-ietf-mpls-rsvp-lsp-tunnel-07.txt"
    ::= { mplsTunnelEntry 29 }

mplsTunnelPathInUse OBJECT-TYPE
    SYNTAX MplsPathIndexOrZero
--    Rsyntax Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This value denotes the configured path that was
         chosen for this tunnel. This value reflects the
         secondary index into the TunnelHopTable. This path
         may not exactly match the one in the ARHopTable
         due to the fact that some CSPF modification may
         have taken place. See the ARHopTable for the
         actual path being taken by the tunnel. A value of
         zero denotes that no path is currently in use or
         available."
    ::= { mplsTunnelEntry 30 }

mplsTunnelRole OBJECT-TYPE
    SYNTAX INTEGER {
        head(1),
        transit(2),
        tail(3)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This value signifies the role that this tunnel
         entry/instance represents. This value MUST be set
         to head(1) at the originating point of the tunnel.
         This value MUST be set to transit(2) at transit
         points along the tunnel, if transit points are
         supported. This value MUST be set to tail(3) at
         the terminating point of the tunnel if tunnel
         tails are supported."
    ::= { mplsTunnelEntry 31 }

mplsTunnelTotalUpTime OBJECT-TYPE
    SYNTAX TimeTicks
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This value represents the aggregate up time for
         all instances of this tunnel, if available. If
         this value is unavailable, it MUST return a value
         of 0."
    ::= { mplsTunnelEntry 32 }

mplsTunnelInstanceUpTime OBJECT-TYPE
    SYNTAX TimeTicks
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This value identifies the total time that this
         tunnel instance's operStatus has been Up(1)."
    ::= { mplsTunnelEntry 33 }

mplsTunnelAdminStatus OBJECT-TYPE
    SYNTAX INTEGER {
        up(1),
        down(2),
        testing(3)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Indicates the desired operational status of this
         tunnel."
    ::= { mplsTunnelEntry 34 }

mplsTunnelOperStatus OBJECT-TYPE
    SYNTAX INTEGER {
        up(1),
        down(2),
        testing(3),
        unknown(4),
        dormant(5),
        notPresent(6),
        lowerLayerDown(7)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Indicates the actual operational status of this
         tunnel, which is typically but not limited to, a
         function of the state of individual segments of
         this tunnel."
    ::= { mplsTunnelEntry 35 }

mplsTunnelRowStatus OBJECT-TYPE
    SYNTAX RowStatus
--    Rsyntax INTEGER {
--        active(1),
--        notInService(2),
--        notReady(3),
--        createAndGo(4),
--        createAndWait(5),
--        destroy(6)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable is used to create, modify, and/or
         delete a row in this table."
    ::= { mplsTunnelEntry 36 }

mplsTunnelStorageType OBJECT-TYPE
    SYNTAX StorageType
--    Rsyntax INTEGER {
--        other(1),
--        volatile(2),
--        nonVolatile(3),
--        permanent(4),
--        readOnly(5)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable indicates the storage type for this
         object."
    ::= { mplsTunnelEntry 37 }

mplsTunnelHopListIndexNext OBJECT-TYPE
    SYNTAX Gauge(0..2147483647)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object contains an appropriate value to be
         used for mplsTunnelHopListIndex when creating
         entries in the mplsTunnelHopTable.  If the number
         of unassigned entries is exhausted, a retrival
         operation will return a value of 0.  This object
         may also return a value of 0 when the LSR is
         unable to accept conceptual row creation, for
         example, if the mplsTunnelHopTable is implemented
         as read-only.  To obtain the value of
         mplsTunnelHopListIndex for a new entry in the
         mplsTunnelHopTable, the manager issues a
         management protocol retrieval operation to obtain
         the current value of mplsTunnelHopIndex.  After
         each retrieval operation, the agent should modify
         the value to reflect the next unassigned index.
         After a manager retrieves a value the agent will
         determine through its local policy when this index
         value will be made available for reuse."
    ::= { mplsTeObjects 3 }

mplsTunnelHopTable OBJECT-TYPE
    SYNTAX SEQUENCE OF MplsTunnelHopEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The mplsTunnelHopTable is used to indicate the
         hops, strict or loose, for an MPLS tunnel defined
         in mplsTunnelTable, when it is established via
         signaling, for the outgoing direction of the
         tunnel.  Each row in this table is indexed by
         mplsTunnelHopListIndex.  Each row also has a
         secondary index mplsTunnelHopIndex corresponding
         to the next hop that this row corresponds to.  The
         first row in the table is the first hop after the
         origination point of the tunnel.  In case we want
         to specify a particular interface on the
         originating LSR of an outgoing tunnel by which we
         want packets to exit the LSR, we specify this as
         the first hop for this tunnel in
        
        
         mplsTunnelHopTable."
    ::= { mplsTeObjects 4 }

mplsTunnelHopEntry OBJECT-TYPE
    SYNTAX MplsTunnelHopEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry in this table represents a tunnel hop.
         An entry is created by a network administrator for
         signaled ERLSP set up by an MPLS signaling
         protocol."
    INDEX { mplsTunnelHopListIndex, mplsPathOptionIndex, mplsTunnelHopIndex }
    ::= { mplsTunnelHopTable 1 }

MplsTunnelHopEntry ::= SEQUENCE {
    mplsTunnelHopListIndex MplsPathIndex,
    mplsPathOptionIndex MplsPathIndex,
    mplsTunnelHopIndex MplsPathIndex,
    mplsTunnelHopAddrType INTEGER,
    mplsTunnelHopIpv4Addr InetAddressIPv4,
    mplsTunnelHopIpv4PrefixLen Gauge,
    mplsTunnelHopIpv6Addr InetAddressIPv6,
    mplsTunnelHopIpv6PrefixLen Gauge,
    mplsTunnelHopAsNumber Gauge,
    mplsTunnelHopLspId MplsLSPID,
    mplsTunnelHopType INTEGER,
    mplsTunnelHopRowStatus RowStatus,
    mplsTunnelHopStorageType StorageType
    }

mplsTunnelHopListIndex OBJECT-TYPE
    SYNTAX MplsPathIndex
--    Rsyntax Gauge
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Primary index into this table identifying a
         particular explicit route object."
    ::= { mplsTunnelHopEntry 1 }

mplsPathOptionIndex OBJECT-TYPE
    SYNTAX MplsPathIndex
--    Rsyntax Gauge
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Secondary index into this table identifying a
         particular group of hops representing a particular
         configured path. This is otherwise known as a path
         option."
    ::= { mplsTunnelHopEntry 2 }

mplsTunnelHopIndex OBJECT-TYPE
    SYNTAX MplsPathIndex
--    Rsyntax Gauge
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Secondary index into this table identifying a
         particular hop."
    ::= { mplsTunnelHopEntry 3 }

mplsTunnelHopAddrType OBJECT-TYPE
    SYNTAX INTEGER {
        ipV4(1),
        ipV6(2),
        asNumber(3),
        lspid(4)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Denotes the address type of this tunnel hop."
    DEFVAL { ipV4 }
    ::= { mplsTunnelHopEntry 4 }

mplsTunnelHopIpv4Addr OBJECT-TYPE
    SYNTAX InetAddressIPv4
--    Rsyntax OCTET STRING(SIZE(4))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelHopAddrType is set to ipV4(1), then
         this value will contain the IPv4 address of this
         hop. This object is otherwise insignificant and
         should contain a value of 0."
    ::= { mplsTunnelHopEntry 5 }

mplsTunnelHopIpv4PrefixLen OBJECT-TYPE
    SYNTAX Gauge(0..32)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelHopAddrType is ipV4(1), then the
         prefix length for this hop's IPv4 address is
         contained herein. This object is otherwise
         insignificant and should contain a value of 0."
    ::= { mplsTunnelHopEntry 6 }

mplsTunnelHopIpv6Addr OBJECT-TYPE
    SYNTAX InetAddressIPv6
--    Rsyntax OCTET STRING(SIZE(16|20))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "If the mplsTunnelHopAddrType is set to ipV6(2),
         then this variable contains the IPv6 address of
         this hop.  This object is otherwise insignificant
         and should contain a value of 0."
    ::= { mplsTunnelHopEntry 7 }

mplsTunnelHopIpv6PrefixLen OBJECT-TYPE
    SYNTAX Gauge(0..128)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelHopAddrType is set to ipV6(2), this
         value will contain the prefix length for this
         hop's IPv6 address. This object is otherwise
         insignificant and should contain a value of 0."
    ::= { mplsTunnelHopEntry 8 }

mplsTunnelHopAsNumber OBJECT-TYPE
    SYNTAX Gauge(0..65535)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelHopAddrType is set to asNumber(3),
         then this value will contain the AS number of this
         hop. This object is otherwise insignificant and
         should contain a value of 0 to indicate this
         fact."
    ::= { mplsTunnelHopEntry 9 }

mplsTunnelHopLspId OBJECT-TYPE
    SYNTAX MplsLSPID
--    Rsyntax OCTET STRING(SIZE(0..31))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelHopAddrType is set to lspid(4), then
         this value will contain the LSPID of a tunnel of
         this hop. The present tunnel being configured is
         ‘tunneled’ through this hop (using label
         stacking). This object is otherwise insignificant
         and should contain a value of 0 to indicate this
         fact."
    ::= { mplsTunnelHopEntry 10 }

mplsTunnelHopType OBJECT-TYPE
    SYNTAX INTEGER {
        strict(1),
        loose(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Denotes whether this tunnel hop is routed in a
         strict or loose fashion."
    ::= { mplsTunnelHopEntry 11 }

mplsTunnelHopRowStatus OBJECT-TYPE
    SYNTAX RowStatus
--    Rsyntax INTEGER {
--        active(1),
--        notInService(2),
--        notReady(3),
--        createAndGo(4),
--        createAndWait(5),
--        destroy(6)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable is used to create, modify, and/or
         delete a row in this table."
    ::= { mplsTunnelHopEntry 12 }

mplsTunnelHopStorageType OBJECT-TYPE
    SYNTAX StorageType
--    Rsyntax INTEGER {
--        other(1),
--        volatile(2),
--        nonVolatile(3),
--        permanent(4),
--        readOnly(5)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable indicates the storage type for this
         object."
    ::= { mplsTunnelHopEntry 13 }

mplsTunnelResourceIndexNext OBJECT-TYPE
    SYNTAX Gauge(0..2147483647)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object contains the next appropriate value to
         be used for mplsTunnelResourceIndex when creating
         entries in the mplsTunnelResourceTable. If the
         number of unassigned entries is exhausted, a
         retrival operation will return a value of 0.  This
         object may also return a value of 0 when the LSR
         is unable to accept conceptual row creation, for
         example, if the mplsTunnelTable is implemented as
         read-only.  To obtain the mplsTunnelResourceIndex
         value for a new entry, the manager must first
         issue a management protocol retrieval operation to
         obtain the current value of this object. The agent
         should modify the value to reflect the next
         unassigned index after each retrieval operation.
         After a manager retrieves a value the agent will
         determine through its local policy when this index
        
        
         value will be made available for reuse."
    ::= { mplsTeObjects 5 }

mplsTunnelResourceTable OBJECT-TYPE
    SYNTAX SEQUENCE OF MplsTunnelResourceEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The mplsTunnelResourceTable allows a manager to
         specify which resources are desired for an MPLS
         tunnel.  This table also allows several tunnels to
         point to a single entry in this table, implying
         that these tunnels should share resources."
    ::= { mplsTeObjects 6 }

mplsTunnelResourceEntry OBJECT-TYPE
    SYNTAX MplsTunnelResourceEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry in this table represents a set of
         resources for an MPLS tunnel.  An entry can be
         created by a network administrator or by an SNMP
         agent as instructed by any MPLS signaling
         protocol."
    INDEX { mplsTunnelResourceIndex }
    ::= { mplsTunnelResourceTable 1 }

MplsTunnelResourceEntry ::= SEQUENCE {
    mplsTunnelResourceIndex Gauge,
    mplsTunnelResourceMaxRate MplsBitRate,
    mplsTunnelResourceMeanRate MplsBitRate,
    mplsTunnelResourceMaxBurstSize MplsBurstSize,
    mplsTunnelResourceRowStatus RowStatus,
    mplsTunnelResourceStorageType StorageType
    }

mplsTunnelResourceIndex OBJECT-TYPE
    SYNTAX Gauge(1..2147483647)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Uniquely identifies this row."
    ::= { mplsTunnelResourceEntry 1 }

mplsTunnelResourceMaxRate OBJECT-TYPE
    SYNTAX MplsBitRate
--    Rsyntax INTEGER(1..2147483647)
--  Units
--    bits per second
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The maximum rate in bits/second.  Note that
         setting mplsTunnelResourceMaxRate,
         mplsTunnelResourceMeanRate, and
         mplsTunnelResourceMaxBurstSize to 0 indicates best-
         effort treatment.
         This object is copied to an instance of
         mplsTrafficParamMaxRate in mplsTrafficParamTable
         the OID of which is copied into the corresponding
         mplsInSegmentTrafficParamPtr."
    REFERENCE
        "Srinivasan, C., Viswanathan, A., and T. Nadeau,
         MPLS Label Switch Router Management Information
         Base Using SMIv2, Internet Draft <draft-ietf-mpls-
         lsr-mib-06.txt>, July 2000."
    ::= { mplsTunnelResourceEntry 2 }

mplsTunnelResourceMeanRate OBJECT-TYPE
    SYNTAX MplsBitRate
--    Rsyntax INTEGER(1..2147483647)
--  Units
--    bits per second
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object is copied into an instance of
         mplsTrafficParamMeanRate in the
         mplsTrafficParamTable. The OID of this table entry
         is then copied into the corresponding
         mplsInSegmentTrafficParamPtr.
        
         When resource allocation is performed as requested
         by this TSpec object, it is copied into an entry
         in mplsTrafficParamTable [LSRMIB]:
         mplsTunnelInMeanRate to mplsTrafficParamMeanRate.
         The OID of this entry is copied to
         mplsInSegmentTrafficParamPtr of the corresponding
         in-segment entry."
    REFERENCE
        "Srinivasan, C., Viswanathan, A., and T. Nadeau,
         MPLS Label Switch Router Management Information
         Base Using SMIv2, Internet Draft <draft-ietf-mpls-
         lsr-mib-06.txt>, July 2000."
    ::= { mplsTunnelResourceEntry 3 }

mplsTunnelResourceMaxBurstSize OBJECT-TYPE
    SYNTAX MplsBurstSize
--    Rsyntax INTEGER(1..2147483647)
--  Units
--    bytes
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The maximum burst size in bytes.  This object is
         copied to mplsInSegmentMaxBurstSize of the
         corresponding in-segment.
        
         When resource allocation is performed as requested
         by this TSpec object, it is copied into an entry
         in mplsTrafficParamTable [LSRMIB]:
         mplsTunnelInMaxBurstSize to
         mplsTrafficParamMaxBurstSize. The OID of this
         entry is copied to mplsInSegmentTrafficParamPtr of
         the corresponding in-segment entry."
    REFERENCE
        "Srinivasan, C., Viswanathan, A., and T. Nadeau,
         MPLS Label Switch Router Management Information
         Base Using SMIv2, Internet Draft <draft-ietf-mpls-
         lsr-mib-06.txt>, July 2000."
    ::= { mplsTunnelResourceEntry 4 }

mplsTunnelResourceRowStatus OBJECT-TYPE
    SYNTAX RowStatus
--    Rsyntax INTEGER {
--        active(1),
--        notInService(2),
--        notReady(3),
--        createAndGo(4),
--        createAndWait(5),
--        destroy(6)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable is used to create, modify, and/or
         delete a row in this table."
    ::= { mplsTunnelResourceEntry 5 }

mplsTunnelResourceStorageType OBJECT-TYPE
    SYNTAX StorageType
--    Rsyntax INTEGER {
--        other(1),
--        volatile(2),
--        nonVolatile(3),
--        permanent(4),
--        readOnly(5)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This variable indicates the storage type for this
         object."
    ::= { mplsTunnelResourceEntry 6 }

mplsTunnelARHopTable OBJECT-TYPE
    SYNTAX SEQUENCE OF MplsTunnelARHopEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The mplsTunnelARHopTable is used to indicate the
         hops, strict or loose, for an MPLS tunnel defined
         in mplsTunnelTable, as reported by the MPLS
         signaling protocol, for the outgoing direction of
        
        
         the tunnel.  Each row in this table is indexed by
         mplsTunnelARHopListIndex.  Each row also has a
         secondary index mplsTunnelARHopIndex,
         corresponding to the next hop that this row
         corresponds to.  The first row in the table is the
         first hop after the origination point of the
         tunnel.  In case we want to specify a particular
         interface on the originating LSR of an outgoing
         tunnel by which we want packets to exit the LSR,
         we specify this as the first hop for this tunnel
         in mplsTunnelARHopTable.
        
         Please note that since the information necessary
         to build entries within this table are not
         provided by some MPLS signaling protocols,
         implementation of this table is optional.
         Furthermore, since the information in this table
         is actually provided by the MPLS signaling
         protocol after the path has been set-up, the
         entries in this table are provided only for
         observation, and hence, all variables in this
         table are accessible exclusively as read-only."
    ::= { mplsTeObjects 7 }

mplsTunnelARHopEntry OBJECT-TYPE
    SYNTAX MplsTunnelARHopEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry in this table represents a tunnel hop.
         An entry is created by a network administrator for
         signaled ERLSP set up by an MPLS signaling
         protocol."
    INDEX { mplsTunnelARHopListIndex, mplsTunnelARHopIndex }
    ::= { mplsTunnelARHopTable 1 }

MplsTunnelARHopEntry ::= SEQUENCE {
    mplsTunnelARHopListIndex Gauge,
    mplsTunnelARHopIndex Gauge,
    mplsTunnelARHopAddrType INTEGER,
    mplsTunnelARHopIpv4Addr InetAddressIPv4,
    mplsTunnelARHopIpv4PrefixLen Gauge,
    mplsTunnelARHopIpv6Addr InetAddressIPv6,
    mplsTunnelARHopIpv6PrefixLen Gauge,
    mplsTunnelARHopAsNumber Gauge,
    mplsTunnelARHopType INTEGER
    }

mplsTunnelARHopListIndex OBJECT-TYPE
    SYNTAX Gauge(1..2147483647)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Primary index into this table identifying a
         particular recorded hop list."
    ::= { mplsTunnelARHopEntry 1 }

mplsTunnelARHopIndex OBJECT-TYPE
    SYNTAX Gauge(1..2147483647)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Secondary index into this table identifying the
         particular hop."
    ::= { mplsTunnelARHopEntry 2 }

mplsTunnelARHopAddrType OBJECT-TYPE
    SYNTAX INTEGER {
        ipV4(1),
        ipV6(2),
        asNumber(3)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Denotes the address type of this tunnel hop."
    DEFVAL { ipV4 }
    ::= { mplsTunnelARHopEntry 3 }

mplsTunnelARHopIpv4Addr OBJECT-TYPE
    SYNTAX InetAddressIPv4
--    Rsyntax OCTET STRING(SIZE(4))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelARHopAddrType is set to ipV4(1), then
         this value will contain the IPv4 address of this
         hop. This object is otherwise insignificant and
         should contain a value of 0."
    ::= { mplsTunnelARHopEntry 4 }

mplsTunnelARHopIpv4PrefixLen OBJECT-TYPE
    SYNTAX Gauge(0..32)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelARHopAddrType is ipV4(1), then the
         prefix length for this hop's IPv4 address is
         contained herein. This object is otherwise
         insignificant and should contain a value of 0."
    ::= { mplsTunnelARHopEntry 5 }

mplsTunnelARHopIpv6Addr OBJECT-TYPE
    SYNTAX InetAddressIPv6
--    Rsyntax OCTET STRING(SIZE(16|20))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If the mplsTunnelARHopAddrType is set to ipV6(2),
         then this variable contains the IPv6 address of
         this hop.  This object is otherwise insignificant
         and should contain a value of 0."
    ::= { mplsTunnelARHopEntry 6 }

mplsTunnelARHopIpv6PrefixLen OBJECT-TYPE
    SYNTAX Gauge(0..128)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelARHopAddrType is set to ipV6(2), this
         value will contain the prefix length for this
         hop's IPv6 address. This object is otherwise
         insignificant and should contain a value of 0."
    ::= { mplsTunnelARHopEntry 7 }

mplsTunnelARHopAsNumber OBJECT-TYPE
    SYNTAX Gauge(0..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelARHopAddrType is set to asNumber(3),
         then this value will contain the AS number of this
         hop. This object is otherwise insignificant and
         should contain a value of 0 to indicate this
         fact."
    ::= { mplsTunnelARHopEntry 8 }

mplsTunnelARHopType OBJECT-TYPE
    SYNTAX INTEGER {
        strict(1),
        loose(2)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Denotes whether this is tunnel hop is routed in a
         strict or loose fashion."
    ::= { mplsTunnelARHopEntry 9 }

mplsTunnelCHopTable OBJECT-TYPE
    SYNTAX SEQUENCE OF MplsTunnelCHopEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "The mplsTunnelCHopTable is used to indicate the
         hops, strict or loose, for an MPLS tunnel defined
         in mplsTunnelTable, as computed by a constraint-
         based routing protocol, based on the
         mplsTunnelHopTable for the outgoing direction of
         the tunnel.  Each row in this table is indexed by
         mplsTunnelCHopListIndex.  Each row also has a
         secondary index mplsTunnelCHopIndex, corresponding
         to the next hop that this row corresponds to.  The
         first row in the table is the first hop after the
         origination point of the tunnel.  In case we want
         to specify a particular interface on the
         originating LSR of an outgoing tunnel by which we
         want packets to exit the LSR, we specify this as
         the first hop for this tunnel in
         mplsTunnelCHopTable.
        
         Please note that since the information necessary
         to build entries within this table may not be
         supported by some LSRs, implementation of this
         table is optional. Furthermore, since the
         information in this table is actually provided by
         routing protocol after the path has been computed,
         the entries in this table are provided only for
         observation, and hence, all variables in this
         table are accessible exclusively as read-only."
    ::= { mplsTeObjects 8 }

mplsTunnelCHopEntry OBJECT-TYPE
    SYNTAX MplsTunnelCHopEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry in this table represents a tunnel hop.
         An entry in this table is created by a constraint-
         based routing protocol based on the hops specified
         in the corresponding mplsTunnelHopTable."
    INDEX { mplsTunnelCHopListIndex, mplsTunnelCHopIndex }
    ::= { mplsTunnelCHopTable 1 }

MplsTunnelCHopEntry ::= SEQUENCE {
    mplsTunnelCHopListIndex Gauge,
    mplsTunnelCHopIndex Gauge,
    mplsTunnelCHopAddrType INTEGER,
    mplsTunnelCHopIpv4Addr InetAddressIPv4,
    mplsTunnelCHopIpv4PrefixLen Gauge,
    mplsTunnelCHopIpv6Addr InetAddressIPv6,
    mplsTunnelCHopIpv6PrefixLen Gauge,
    mplsTunnelCHopAsNumber Gauge,
    mplsTunnelCHopType INTEGER
    }

mplsTunnelCHopListIndex OBJECT-TYPE
    SYNTAX Gauge(1..2147483647)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Primary index into this table identifying a
         particular computed hop list."
    ::= { mplsTunnelCHopEntry 1 }

mplsTunnelCHopIndex OBJECT-TYPE
    SYNTAX Gauge(1..2147483647)
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "Secondary index into this table identifying the
         particular hop."
    ::= { mplsTunnelCHopEntry 2 }

mplsTunnelCHopAddrType OBJECT-TYPE
    SYNTAX INTEGER {
        ipV4(1),
        ipV6(2),
        asNumber(3)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Denotes the address type of this tunnel hop."
    DEFVAL { ipV4 }
    ::= { mplsTunnelCHopEntry 3 }

mplsTunnelCHopIpv4Addr OBJECT-TYPE
    SYNTAX InetAddressIPv4
--    Rsyntax OCTET STRING(SIZE(4))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelCHopAddrType is set to ipV4(1), then
         this value will contain the IPv4 address of this
         hop. This object is otherwise insignificant and
         should contain a value of 0."
    ::= { mplsTunnelCHopEntry 4 }

mplsTunnelCHopIpv4PrefixLen OBJECT-TYPE
    SYNTAX Gauge(0..32)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelCHopAddrType is ipV4(1), then the
         prefix length for this hop's IPv4 address is
         contained herein. This object is otherwise
         insignificant and should contain a value of 0."
    ::= { mplsTunnelCHopEntry 5 }

mplsTunnelCHopIpv6Addr OBJECT-TYPE
    SYNTAX InetAddressIPv6
--    Rsyntax OCTET STRING(SIZE(16|20))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If the mplsTunnelCHopAddrType is set to ipV6(2),
         then this variable contains the IPv6 address of
         this hop.  This object is otherwise insignificant
         and should contain a value of 0."
    ::= { mplsTunnelCHopEntry 6 }

mplsTunnelCHopIpv6PrefixLen OBJECT-TYPE
    SYNTAX Gauge(0..128)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelCHopAddrType is set to ipV6(2), this
         value will contain the prefix length for this
         hop's IPv6 address. This object is otherwise
         insignificant and should contain a value of 0."
    ::= { mplsTunnelCHopEntry 7 }

mplsTunnelCHopAsNumber OBJECT-TYPE
    SYNTAX Gauge(0..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "If mplsTunnelCHopAddrType is set to asNumber(3),
         then this value will contain the AS number of this
         hop. This object is otherwise insignificant and
         should contain a value of 0 to indicate this
         fact."
    ::= { mplsTunnelCHopEntry 8 }

mplsTunnelCHopType OBJECT-TYPE
    SYNTAX INTEGER {
        strict(1),
        loose(2)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Denotes whether this is tunnel hop is routed in a
         strict or loose fashion."
    ::= { mplsTunnelCHopEntry 9 }

mplsTunnelPerfTable OBJECT-TYPE
    SYNTAX SEQUENCE OF MplsTunnelPerfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table provides per-tunnel MPLS performance
         information."
    ::= { mplsTeObjects 9 }

mplsTunnelPerfEntry OBJECT-TYPE
    SYNTAX MplsTunnelPerfEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "An entry in this table is created by the LSR for
         every tunnel.  Its is an extension to
         mplsTunnelEntry."
    INDEX { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId }
-- Augments mplsTunnelEntry
    ::= { mplsTunnelPerfTable 1 }

MplsTunnelPerfEntry ::= SEQUENCE {
    mplsTunnelPerfPackets Counter,
    mplsTunnelPerfHCPackets Counter,
    mplsTunnelPerfErrors Counter,
    mplsTunnelPerfBytes Counter,
    mplsTunnelPerfHCBytes Counter
    }

mplsTunnelPerfPackets OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Number of packets forwarded by the tunnel."
    ::= { mplsTunnelPerfEntry 1 }

mplsTunnelPerfHCPackets OBJECT-TYPE
    SYNTAX --?? syntax is not convertable to SMIv1
           Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "High capacity counter for number of packets
         forwarded by the tunnel."
    ::= { mplsTunnelPerfEntry 2 }

mplsTunnelPerfErrors OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Number of errored packets."
    ::= { mplsTunnelPerfEntry 3 }

mplsTunnelPerfBytes OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Number of bytes forwarded by the tunnel."
    ::= { mplsTunnelPerfEntry 4 }

mplsTunnelPerfHCBytes OBJECT-TYPE
    SYNTAX --?? syntax is not convertable to SMIv1
           Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "High capacity counter for number of bytes
         forwarded by the tunnel."
    ::= { mplsTunnelPerfEntry 5 }

mplsTunnelTrapEnable OBJECT-TYPE
    SYNTAX TruthValue
--    Rsyntax INTEGER {
--        true(1),
--        false(2)
--        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "If this object is true, then it enables the
         generation of mplsTunnelUp and mplsTunnelDown
         traps, otherwise these traps are not emitted."
    DEFVAL { false }
    ::= { mplsTeObjects 10 }

mplsTunnelUp TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE mplsTeNotifications
    VARIABLES {
        mplsTunnelAdminStatus, mplsTunnelOperStatus }
--  Status
--    mandatory
    DESCRIPTION
        "This notification is generated when a
         mplsTunnelOperStatus object for one of the
         configured tunnels is about to leave the down
         state and transition into some other state (but
         not into the notPresent state).  This other state
         is indicated by the included value of
         mplsTunnelOperStatus."
    ::= 1

mplsTunnelDown TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE mplsTeNotifications
    VARIABLES {
        mplsTunnelAdminStatus, mplsTunnelOperStatus }
--  Status
--    mandatory
    DESCRIPTION
        "This notification is generated when a
         mplsTunnelOperStatus object for one of the
         configured tunnels is about to enter the down
         state from some other state (but not from the
         notPresent state).  This other state is indicated
         by the included value of mplsTunnelOperStatus."
    ::= 2

mplsTunnelRerouted TRAP-TYPE
-- Reverse mappable trap
    ENTERPRISE mplsTeNotifications
    VARIABLES {
        mplsTunnelAdminStatus, mplsTunnelOperStatus }
--  Status
--    mandatory
    DESCRIPTION
        "This notification is generated when a tunnel is
         rerouted or re-optimized. If the Actual Path is
         used, then this object MAY contain the new path
         for this tunnel some time after this trap is
        
        
         issued by the agent."
    ::= 3

mplsTunnelGroup OBJECT IDENTIFIER ::= { mplsTeGroups 1 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    Necessary, but not sufficient, set of objects to
--     implement tunnels.  In addition, depending on the
--     type of the tunnels supported (for example,
--     manually configured or signaled, persistent or non-
--     persistent, etc.), the following other groups
--     defined below are mandatory: mplsTunnelManualGroup
--     and/or mplsTunnelSignaledGroup,
--     mplsTunnelIsNotIntfcGroup and/or
--     mplsTunnelIsIntfcGroup.
--  objects
--    mplsTunnelIndexNext, mplsTunnelName, mplsTunnelDescr, 
--    mplsTunnelOwner, mplsTunnelXCPointer, mplsTunnelIfIndex, 
--    mplsTunnelHopTableIndex, mplsTunnelARHopTableIndex, 
--    mplsTunnelCHopTableIndex, mplsTunnelAdminStatus, 
--    mplsTunnelOperStatus, mplsTunnelRowStatus, 
--    mplsTunnelTrapEnable, mplsTunnelStorageType, 
--    mplsTunnelConfigured, mplsTunnelActive, 
--    mplsTunnelPrimaryInstance, mplsTunnelPrimaryTimeUp, 
--    mplsTunnelPathChanges, mplsTunnelLastPathChange, 
--    mplsTunnelCreationTime, mplsTunnelStateTransitions, 
--    mplsTunnelEgressLSRId, mplsTunnelIncludeAnyAffinity, 
--    mplsTunnelIncludeAllAffinity, mplsTunnelExcludeAllAffinity, 
--    mplsTunnelPerfPackets, mplsTunnelPerfHCPackets, 
--    mplsTunnelPerfErrors, mplsTunnelPerfBytes, 
--    mplsTunnelPerfHCBytes, mplsTunnelResourcePointer, 
--    mplsTunnelInstancePriority, mplsTunnelPathInUse, 
--    mplsTunnelRole, mplsTunnelTotalUpTime, 
--    mplsTunnelInstanceUpTime

mplsTunnelManualGroup OBJECT IDENTIFIER ::= { mplsTeGroups 2 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    Object(s) needed to implement manually configured
--     tunnels.
--  objects
--    mplsTunnelSignallingProto

mplsTunnelSignaledGroup OBJECT IDENTIFIER ::= { mplsTeGroups 3 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    Object needed to implement signaled tunnels.
--  objects
--    mplsTunnelSetupPrio, mplsTunnelHoldingPrio, 
--    mplsTunnelSignallingProto, mplsTunnelLocalProtectInUse, 
--    mplsTunnelSessionAttributes, mplsTunnelHopListIndexNext, 
--    mplsTunnelHopAddrType, mplsTunnelHopIpv4Addr, 
--    mplsTunnelHopIpv4PrefixLen, mplsTunnelHopIpv6Addr, 
--    mplsTunnelHopIpv6PrefixLen, mplsTunnelHopAsNumber, 
--    mplsTunnelHopLspId, mplsTunnelHopType, mplsTunnelHopRowStatus, 
--    mplsTunnelHopStorageType

mplsTunnelScalarGroup OBJECT IDENTIFIER ::= { mplsTeGroups 4 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    Scalar object needed to implement MPLS tunnels.
--  objects
--    mplsTunnelConfigured, mplsTunnelActive, mplsTunnelTEDistProto, 
--    mplsTunnelMaxHops

mplsTunnelIsIntfcGroup OBJECT IDENTIFIER ::= { mplsTeGroups 5 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    Objects needed to implement tunnels that are
--     interfaces.
--  objects
--    mplsTunnelIsIf

mplsTunnelIsNotIntfcGroup OBJECT IDENTIFIER ::= { mplsTeGroups 6 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    Objects needed to implement tunnels that are not
--     interfaces.
--  objects
--    mplsTunnelIsIf

mplsTunnelOptionalGroup OBJECT IDENTIFIER ::= { mplsTeGroups 7 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    The objects in this group are optional.
--  objects
--    mplsTunnelResourceIndexNext, mplsTunnelResourceMaxRate, 
--    mplsTunnelResourceMeanRate, mplsTunnelResourceMaxBurstSize, 
--    mplsTunnelResourceRowStatus, mplsTunnelResourceStorageType, 
--    mplsTunnelARHopAddrType, mplsTunnelARHopIpv4Addr, 
--    mplsTunnelARHopIpv4PrefixLen, mplsTunnelARHopIpv6Addr, 
--    mplsTunnelARHopIpv6PrefixLen, mplsTunnelARHopAsNumber, 
--    mplsTunnelARHopType, mplsTunnelCHopAddrType, 
--    mplsTunnelCHopIpv4Addr, mplsTunnelCHopIpv4PrefixLen, 
--    mplsTunnelCHopIpv6Addr, mplsTunnelCHopIpv6PrefixLen, 
--    mplsTunnelCHopAsNumber, mplsTunnelCHopType

mplsTeNotificationGroup OBJECT IDENTIFIER ::= { mplsTeGroups 8 }
-- NOTIFICATION-GROUP
--  Status
--    mandatory
--  Descr
--    Set of notifications implemented in this module.
--     None is mandatory.
--  notifications
--    mplsTunnelUp, mplsTunnelDown, mplsTunnelRerouted

mplsTeModuleCompliance OBJECT IDENTIFIER ::= { mplsTeCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--    Compliance statement for agents that support the
--     MPLS TE MIB.
--  Module
--    >>current<<
--   MandGroup
--    mplsTunnelGroup
--   MandGroup
--    mplsTunnelScalarGroup
--   OptGroup
--    mplsTunnelManualGroup
--   OptGroup
--    mplsTunnelSignaledGroup
--   OptGroup
--    mplsTunnelIsNotIntfcGroup
--   OptGroup
--    mplsTunnelIsIntfcGroup
--   OptGroup
--    mplsTunnelOptionalGroup
--   ObjVar
--    mplsTunnelName
--   ObjVar
--    mplsTunnelDescr
--   ObjVar
--    mplsTunnelIsIf
--   ObjVar
--    mplsTunnelIfIndex
--   ObjVar
--    mplsTunnelXCPointer
--   ObjVar
--    mplsTunnelSignallingProto
--   ObjVar
--    mplsTunnelSetupPrio
--   ObjVar
--    mplsTunnelHoldingPrio
--   ObjVar
--    mplsTunnelSessionAttributes
--   ObjVar
--    mplsTunnelOwner
--   ObjVar
--    mplsTunnelLocalProtectInUse
--   ObjVar
--    mplsTunnelResourcePointer
--   ObjVar
--    mplsTunnelInstancePriority
--   ObjVar
--    mplsTunnelPrimaryInstance
--   ObjVar
--    mplsTunnelPrimaryTimeUp
--   ObjVar
--    mplsTunnelPathChanges
--   ObjVar
--    mplsTunnelLastPathChange
--   ObjVar
--    mplsTunnelCreationTime
--   ObjVar
--    mplsTunnelStateTransitions
--   ObjVar
--    mplsTunnelHopTableIndex
--   ObjVar
--    mplsTunnelARHopTableIndex
--   ObjVar
--    mplsTunnelCHopTableIndex
--   ObjVar
--    mplsTunnelAdminStatus
--   ObjVar
--    mplsTunnelOperStatus
--   ObjVar
--    mplsTunnelRowStatus
--   ObjVar
--    mplsTunnelStorageType
--   ObjVar
--    mplsTunnelPathInUse
--   ObjVar
--    mplsTunnelRole
--   ObjVar
--    mplsTunnelTotalUpTime
--   ObjVar
--    mplsTunnelInstanceUpTime
--   ObjVar
--    mplsTunnelHopAddrType
--   ObjVar
--    mplsTunnelHopIpv4Addr
--   ObjVar
--    mplsTunnelHopIpv4PrefixLen
--   ObjVar
--    mplsTunnelHopIpv6Addr
--   ObjVar
--    mplsTunnelHopIpv6PrefixLen
--   ObjVar
--    mplsTunnelHopAsNumber
--   ObjVar
--    mplsTunnelHopLspId
--   ObjVar
--    mplsTunnelHopType
--   ObjVar
--    mplsTunnelHopRowStatus
--   ObjVar
--    mplsTunnelHopStorageType
--   ObjVar
--    mplsTunnelResourceMaxRate
--   ObjVar
--    mplsTunnelResourceMeanRate
--   ObjVar
--    mplsTunnelResourceMaxBurstSize
--   ObjVar
--    mplsTunnelResourceRowStatus
--   ObjVar
--    mplsTunnelResourceStorageType
--   ObjVar
--    mplsTunnelPerfPackets
--   ObjVar
--    mplsTunnelPerfHCPackets
--   ObjVar
--    mplsTunnelPerfErrors
--   ObjVar
--    mplsTunnelPerfBytes
--   ObjVar
--    mplsTunnelPerfHCBytes


END