-- MIB file created 10-Jul-2014 20:17:22, by -- SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com SYSLOG-MIB DEFINITIONS ::= BEGIN -- From file: "SYSLOG-MIB.my" -- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T" IMPORTS mib-2 FROM SNMPv2-SMI-v1 RowStatus, StorageType, TimeStamp FROM SNMPv2-TC-v1 InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB SyslogFacility, SyslogSeverity FROM SYSLOG-TC-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB Counter, Gauge FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215; syslogMIB OBJECT IDENTIFIER ::= { mib-2 200 } -- MODULE-IDENTITY -- LastUpdated -- 200703040000Z -- OrgName -- IETF Syslog Working Group -- ContactInfo -- Glenn Mansfield Keeni -- Postal: Cyber Solutions Inc. -- 6-6-3, Minami Yoshinari -- Aoba-ku, Sendai, Japan 989-3204. -- Tel: +81-22-303-4012 -- Fax: +81-22-303-4015 -- E-mail: glenn@cysols.com -- -- Support Group E-mail: syslog@ietf.org -- -- Descr -- The MIB module for monitoring syslog applications. -- -- A syslog application sends and/or receives syslog messages. -- The reader is referred to [RFCPROT] for a description of -- the various roles of a syslog application viz. ''sender'', -- ''receiver'' and ''relay''. The discussion in this -- document in general applies to a generic syslog application. -- For special cases the specific role of the syslog -- application will be mentioned. -- -- -- Copyright (C) The IETF Trust (2008). This version of -- this MIB module is part of RFC XXXX; see the RFC itself for -- full legal notices. -- RevDate -- 200703040000Z -- RevDescr -- The initial version, published as RFC XXXX. syslogNotifications OBJECT IDENTIFIER ::= { syslogMIB 0 } syslogObjects OBJECT IDENTIFIER ::= { syslogMIB 1 } syslogConformance OBJECT IDENTIFIER ::= { syslogMIB 3 } syslogGroups OBJECT IDENTIFIER ::= { syslogConformance 1 } syslogCompliances OBJECT IDENTIFIER ::= { syslogConformance 2 } SyslogRoles ::= OCTET STRING(SIZE(1..2)) -- BITS are: -- sender(0) -- receiver(1) -- relay(2) -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This textual convention enumerates the roles of a -- syslog application. Note that a syslog application can -- have multiple roles. -- Refer -- The Syslog Protocol [RFCPROT] sec. 3. SyslogEncapsulation ::= INTEGER { other(1), none(2), tls(3), beep(4) } -- TEXTUAL-CONVENTION -- Status -- mandatory -- Descr -- This textual convention enumerates the encapsulations -- of the syslog message that is used between syslog -- application endpoints. -- Refer -- Transmission of syslog messages over UDP [RFCUDPX], -- TLS Transport Mapping for Syslog [RFCTLSX], -- Reliable Delivery for syslog [RFC3195]. syslogControlTable OBJECT-TYPE SYNTAX SEQUENCE OF SyslogControlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing the configuration parameters pertaining to the syslog applications serviced by an SNMP agent." ::= { syslogObjects 1 } syslogControlEntry OBJECT-TYPE SYNTAX SyslogControlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The configuration parameters pertaining to a syslog application." INDEX { syslogControlIndex } ::= { syslogControlTable 1 } SyslogControlEntry ::= SEQUENCE { syslogControlIndex Gauge, syslogControlDescr SnmpAdminString, syslogControlRoles SyslogRoles, syslogControlBindAddrType InetAddressType, syslogControlBindAddr InetAddress, syslogControlBindPort InetPortNumber, syslogControlEncapsulation SyslogEncapsulation, syslogControlMaxMessageSize Gauge, syslogControlConfFileName SnmpAdminString, syslogControlStorageType StorageType, syslogControlRowStatus RowStatus } syslogControlIndex OBJECT-TYPE SYNTAX Gauge(1..2147483647) ACCESS not-accessible STATUS mandatory DESCRIPTION "The Index that uniquely identifies the syslog application in the syslogControlTable. The value of the index for a syslog application may not be the same across system reboots. Users and applications will need to determine the index of a syslog application after system reboots." ::= { syslogControlEntry 1 } syslogControlDescr OBJECT-TYPE SYNTAX SnmpAdminString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "A user definable description of the syslog application. This description could be used by syslog management applications e.g. in reports or in user interfaces." ::= { syslogControlEntry 2 } syslogControlRoles OBJECT-TYPE SYNTAX SyslogRoles -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- sender(0) -- receiver(1) -- relay(2) ACCESS read-write STATUS mandatory DESCRIPTION "The roles of the syslog application." ::= { syslogControlEntry 3 } syslogControlBindAddrType OBJECT-TYPE SYNTAX InetAddressType -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- unknown(0), -- ipv4(1), -- ipv6(2), -- ipv4z(3), -- ipv6z(4), -- dns(16) -- } ACCESS read-write STATUS mandatory DESCRIPTION "The type of Internet address which follows in syslogControlBindAddr. If this syslog application is not a syslog receiver, the value of this object will be 'unknown' (0)." ::= { syslogControlEntry 4 } syslogControlBindAddr OBJECT-TYPE SYNTAX InetAddress -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "The specific address the syslog receiver will bind to. The format of the address is specified by the corresponding syslogControlBindAddrType object. If the address is specified in the DNS domain name format [syslogControlBindAddrType = 'dns'], the corresponding IPv4 or IPv6 address obtained at the time of the binding operation by the syslog application, will be used. If this syslog application is not a syslog receiver, the value of this object will be a zero-length string." ::= { syslogControlEntry 5 } syslogControlBindPort OBJECT-TYPE SYNTAX InetPortNumber -- Rsyntax Gauge(0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The port number that this syslog receiver will bind to. If this syslog application is not a syslog receiver the value of this object will be zero." ::= { syslogControlEntry 6 } syslogControlEncapsulation OBJECT-TYPE SYNTAX SyslogEncapsulation -- Rsyntax INTEGER { -- other(1), -- none(2), -- tls(3), -- beep(4) -- } ACCESS read-write STATUS mandatory DESCRIPTION "The encapsulation that will be used for syslog messages by the syslog receiver. If this syslog application is not a syslog receiver the value of this object will be ''other''." ::= { syslogControlEntry 7 } syslogControlMaxMessageSize OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "The maximum size of the syslog messages in bytes for this syslog application. A syslog receiver may reject or truncate messages larger than the specified maximum syslog message size." REFERENCE "The Syslog Protocol [RFCPROT] sec. 6.1. " ::= { syslogControlEntry 8 } syslogControlConfFileName OBJECT-TYPE SYNTAX SnmpAdminString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "The fullpath name of the configuration file where the syslog application's message selection and corresponding action rules will be read from. If the syslog application does not support the specification of a configuration file, the value of this object will be a zero-length string." DEFVAL { "/etc/syslog.conf" } ::= { syslogControlEntry 9 } syslogControlStorageType OBJECT-TYPE SYNTAX StorageType -- Rsyntax INTEGER { -- other(1), -- volatile(2), -- nonVolatile(3), -- permanent(4), -- readOnly(5) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object defines whether the parameters defined in this row are kept in volatile storage and lost upon reboot or are backed up by non-volatile or permanent storage. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { syslogControlEntry 11 } syslogControlRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create, modify and delete rows in the syslogControlTable. The value of syslogControlDescr can be changed when this object is in state ''active'' or in ''notInService''. The other objects in a row can be modified only when the value of this object in the corresponding conceptual row is not ''active''. Thus to modify one or more of the objects in this conceptual row, a. change the row status to ''notInService'', b. change the values of the row c. change the row status to ''active'' The syslogControlRowStatus may be changed to ''active'' if all the managed objects in the conceptual row with MAX-ACCESS read-create except syslogControlBindPort and syslogControlEncapsulation have been assigned valid values." ::= { syslogControlEntry 12 } syslogOperationsTable OBJECT-TYPE SYNTAX SEQUENCE OF SyslogOperationsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing operations information about the syslog applications serviced by an SNMP agent. This table complements the (configuration) information in syslogControlTable ." ::= { syslogObjects 2 } syslogOperationsEntry OBJECT-TYPE SYNTAX SyslogOperationsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The operations information pertaining to a syslog application." INDEX { syslogControlIndex } -- Augments syslogControlEntry ::= { syslogOperationsTable 1 } SyslogOperationsEntry ::= SEQUENCE { syslogOperationsMsgsReceived Counter, syslogOperationsMsgsTransmitted Counter, syslogOperationsMsgsRelayed Counter, syslogOperationsMsgsDropped Counter, syslogOperationsMsgsMalFormed Counter, syslogOperationsMsgsDiscarded Counter, syslogOperationsLastMsgRecdTime TimeStamp, syslogOperationsLastMsgTransmittedTime TimeStamp, syslogOperationsStartTime TimeStamp, syslogOperationsLastError SnmpAdminString, syslogOperationsLastErrorTime TimeStamp, syslogOperationsRunIndex INTEGER, syslogOperationsCounterDiscontinuityTime TimeStamp, syslogOperationsStatus INTEGER } syslogOperationsMsgsReceived OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of messages received by the syslog receiver. This includes messages that were discarded. If this syslog application is not a syslog receiver the value of this object will be zero. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of syslogOperationsCounterDiscontinuityTime." ::= { syslogOperationsEntry 1 } syslogOperationsMsgsTransmitted OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of messages transmitted by the syslog sender. This does not include the messages that could not be queued for transmission by the syslog sender. If this syslog application is not a syslog sender the value of this object will be zero. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of syslogOperationsCounterDiscontinuityTime." ::= { syslogOperationsEntry 2 } syslogOperationsMsgsRelayed OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of messages relayed by the syslog relay to other syslog applications. If this syslog application is not a syslog relay the value of this object will be zero. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of syslogOperationsCounterDiscontinuityTime." REFERENCE "The Syslog Protocol [RFCPROT] sec. 3." ::= { syslogOperationsEntry 3 } syslogOperationsMsgsDropped OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of messages that could not be queued for transmission by the syslog sender. If this syslog application is not a syslog sender the value of this object will be zero. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of syslogOperationsCounterDiscontinuityTime." ::= { syslogOperationsEntry 4 } syslogOperationsMsgsMalFormed OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of messages received by the syslog receiver which had malformed header. If this syslog application is not a syslog receiver, then this object will have a zero value. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of syslogOperationsCounterDiscontinuityTime." REFERENCE "The Syslog Protocol [RFCPROT] sec. 6.3." ::= { syslogOperationsEntry 5 } syslogOperationsMsgsDiscarded OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of messages that were discarded by the syslog receiver. This will include messages that were discarded because the message size was greater than the system's maximum message size. If this syslog application is not a syslog receiver this object will have a zero value. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of syslogOperationsCounterDiscontinuityTime." REFERENCE "The Syslog Protocol [RFCPROT] sec. 6.1." ::= { syslogOperationsEntry 6 } syslogOperationsLastMsgRecdTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime when the last message was received by the syslog receiver. If this syslog application is not a syslog receiver or, if no messages have been received by this syslog application, since the last re-initialization of the local SNMP management subsystem, then this object will have a zero value." ::= { syslogOperationsEntry 7 } syslogOperationsLastMsgTransmittedTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime when the last message was transmitted by the syslog sender. If this syslog application is not a syslog sender or, if no messages have been transmitted by this syslog application, since the last re-initialization of the local management subsystem, then this object will have a zero value." ::= { syslogOperationsEntry 8 } syslogOperationsStartTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime when this syslog application was started." ::= { syslogOperationsEntry 9 } syslogOperationsLastError OBJECT-TYPE SYNTAX SnmpAdminString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "A description of the last error related to sending, receiving or processing a syslog message that was encountered by this syslog application. If no error has been encountered by this syslog application then the value of this object will be a zero-length string. If no error has been encountered by this syslog application since the last re-initialization of the local management subsystem then the value of this object will be a zero-length string." ::= { syslogOperationsEntry 10 } syslogOperationsLastErrorTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime when the last error was encountered. If no error has been encountered by this syslog application since the last re-initialization of the local management subsystem, then this object will have a zero value." ::= { syslogOperationsEntry 11 } syslogOperationsRunIndex OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "If the Host resource MIB is instantiated on the host then this entry will have the value of the hrSWRunIndex of the corresponding entry in the hrSWRunTable. Note that the hrSWRunIndex is not persistent across system reboots or software restarts. The value of syslogOperationsRunIndex SHOULD reference the latest value of the hrSWRunIndex of the corresponding entry in the hrSWRunTable. The special value of zero indicates that the Host resource MIB is not instantiated." ::= { syslogOperationsEntry 12 } syslogOperationsCounterDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime on the most recent occasion at which any one or more of this syslog application's counters, viz., counters with OID prefix 'syslogOperationsMsgsReceived' or 'syslogOperationsMsgsTransmitted' or 'syslogOperationsMsgsRelayed' or 'syslogOperationsMsgsDropped' or 'syslogOperationsMsgsMalFormed' or 'syslogOperationsMsgsDiscarded' suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object will have a zero value." ::= { syslogOperationsEntry 13 } syslogOperationsStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), started(2), suspended(3), stopped(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of the syslog application." -- DEFVAL { unknown } ::= { syslogOperationsEntry 14 } syslogPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF SyslogPriorityEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing the relay configuration parameters pertaining to the syslog applications serviced by an SNMP agent." ::= { syslogObjects 3 } syslogPriorityEntry OBJECT-TYPE SYNTAX SyslogPriorityEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The relay configuration parameters pertaining to a syslog application." INDEX { syslogControlIndex, syslogPriorityFacility, syslogPrioritySeverity } ::= { syslogPriorityTable 1 } SyslogPriorityEntry ::= SEQUENCE { syslogPriorityFacility SyslogFacility, syslogPrioritySeverity SyslogSeverity, syslogPriorityDescr SnmpAdminString, syslogPriorityDestinationIndex Gauge, syslogPriorityStorageType StorageType, syslogPriorityRowStatus RowStatus } syslogPriorityFacility OBJECT-TYPE SYNTAX SyslogFacility -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- kern(0), -- user(1), -- mail(2), -- daemon(3), -- auth(4), -- syslog(5), -- lpr(6), -- news(7), -- uucp(8), -- cron(9), -- authpriv(10), -- ftp(11), -- ntp(12), -- audit(13), -- console(14), -- cron2(15), -- local0(16), -- local1(17), -- local2(18), -- local3(19), -- local4(20), -- local5(21), -- local6(22), -- local7(23) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The facility value of this entry." ::= { syslogPriorityEntry 1 } syslogPrioritySeverity OBJECT-TYPE SYNTAX SyslogSeverity -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- emerg(0), -- alert(1), -- crit(2), -- err(3), -- warning(4), -- notice(5), -- info(6), -- debug(7) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The severity value of this entry." ::= { syslogPriorityEntry 2 } syslogPriorityDescr OBJECT-TYPE SYNTAX SnmpAdminString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "A textual description of this priority entry." ::= { syslogPriorityEntry 3 } syslogPriorityDestinationIndex OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "On systems where the priority value in a syslog message indicates the destination to which a syslog message should be relayed, the value of this object will identify the row in syslogRelayTable that contains information about the relay destination to which messages which have the priority value represented by syslogPriorityFacility and syslogPrioritySeverity values of this row will be relayed. A value of 0 will indicate that there is no corresponding row in the syslogRelayTable table." ::= { syslogPriorityEntry 4 } syslogPriorityStorageType OBJECT-TYPE SYNTAX StorageType -- Rsyntax INTEGER { -- other(1), -- volatile(2), -- nonVolatile(3), -- permanent(4), -- readOnly(5) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object defines whether the parameters defined in this row are kept in volatile storage and lost upon reboot or are backed up by non-volatile or permanent storage. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { syslogPriorityEntry 5 } syslogPriorityRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create, modify and delete rows in the syslogPriorityTable. The value of syslogPriorityDescr can be changed when this object is in state ''active'' or in ''notInService''. The other objects in a row can be modified only when the value of this object in the corresponding conceptual row is not ''active''. Thus to modify one or more of the objects in this conceptual row, a. change the row status to ''notInService'', b. change the values of the row c. change the row status to ''active'' The syslogPriorityRowStatus may be changed to ''active'' if all the managed objects in the conceptual row with MAX-ACCESS read-create have been assigned valid values." ::= { syslogPriorityEntry 6 } syslogRelayTable OBJECT-TYPE SYNTAX SEQUENCE OF SyslogRelayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing information for the relay destinations." ::= { syslogObjects 4 } syslogRelayEntry OBJECT-TYPE SYNTAX SyslogRelayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The information pertaining to a syslog message relay destination." INDEX { syslogRelayIndex } ::= { syslogRelayTable 1 } SyslogRelayEntry ::= SEQUENCE { syslogRelayIndex Gauge, syslogRelayDescr SnmpAdminString, syslogRelayAddrType InetAddressType, syslogRelayAddr InetAddress, syslogRelayPort InetPortNumber, syslogRelayEncapsulation SyslogEncapsulation, syslogRelayMsgsRelayed Counter, syslogRelayCounterDiscontinuityTime TimeStamp, syslogRelayStorageType StorageType, syslogRelayRowStatus RowStatus } syslogRelayIndex OBJECT-TYPE SYNTAX Gauge(1..2147483647) ACCESS not-accessible STATUS mandatory DESCRIPTION "The Index that uniquely identifies the syslog relay in the syslogRelayTable. The value of the index for a syslog relay may not be the same across system reboots. Users and applications will need to determine the index of a syslog relay after system reboots." ::= { syslogRelayEntry 1 } syslogRelayDescr OBJECT-TYPE SYNTAX SnmpAdminString -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "A user definable description of the syslog relay. This description could be used by syslog management applications e.g. in reports or in user interfaces." ::= { syslogRelayEntry 2 } syslogRelayAddrType OBJECT-TYPE SYNTAX InetAddressType -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- unknown(0), -- ipv4(1), -- ipv6(2), -- ipv4z(3), -- ipv6z(4), -- dns(16) -- } ACCESS read-write STATUS mandatory DESCRIPTION "The type of Internet address which follows in syslogRelayAddr." ::= { syslogRelayEntry 3 } syslogRelayAddr OBJECT-TYPE SYNTAX InetAddress -- Rsyntax OCTET STRING(SIZE(0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "The address of the syslog relay . The format of the address is specified by the corresponding syslogRelayAddrType object. If the address is specified in the DNS domain name format [syslogRelayAddrType = 'dns'], the corresponding IPv4 or IPv6 address obtained at the time of the relay operation by the syslog application, will be used." ::= { syslogRelayEntry 4 } syslogRelayPort OBJECT-TYPE SYNTAX InetPortNumber -- Rsyntax Gauge(0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "The port number of the syslog relay." ::= { syslogRelayEntry 5 } syslogRelayEncapsulation OBJECT-TYPE SYNTAX SyslogEncapsulation -- Rsyntax INTEGER { -- other(1), -- none(2), -- tls(3), -- beep(4) -- } ACCESS read-write STATUS mandatory DESCRIPTION "The encapsulation that will be used for syslog messages sent by the syslog sender to the relay destination." ::= { syslogRelayEntry 6 } syslogRelayMsgsRelayed OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of messages relayed by the syslog relay to this relay destination. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of syslogRelayCounterDiscontinuityTime." REFERENCE "The Syslog Protocol [RFCPROT] sec. 3." ::= { syslogRelayEntry 7 } syslogRelayCounterDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp -- Rsyntax TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime on the most recent occasion at which counters with OID prefix 'syslogRelayMsgsRelayed' suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object will have a zero value." ::= { syslogRelayEntry 8 } syslogRelayStorageType OBJECT-TYPE SYNTAX StorageType -- Rsyntax INTEGER { -- other(1), -- volatile(2), -- nonVolatile(3), -- permanent(4), -- readOnly(5) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object defines whether the parameters defined in this row are kept in volatile storage and lost upon reboot or are backed up by non-volatile or permanent storage. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { syslogRelayEntry 9 } syslogRelayRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create, modify and delete rows in the syslogRelayTable. The value of syslogRelayDescr can be changed when this object is in state ''active'' or in ''notInService''. The other objects in a row can be modified only when the value of this object in the corresponding conceptual row is not ''active''. Thus to modify one or more of the objects in this conceptual row, a. change the row status to ''notInService'', b. change the values of the row c. change the row status to ''active'' The syslogRelayRowStatus may be changed to ''active'' if all the managed objects in the conceptual row with MAX-ACCESS read-create have been assigned valid values." ::= { syslogRelayEntry 10 } syslogStatusChanged TRAP-TYPE -- Reverse mappable trap ENTERPRISE syslogMIB VARIABLES { syslogControlDescr, syslogControlRoles, syslogControlBindAddrType, syslogControlBindAddr, syslogControlBindPort, syslogControlEncapsulation, syslogControlConfFileName, syslogOperationsStatus } -- Status -- mandatory DESCRIPTION "This notification is sent when a syslog application changes state. For example when the syslog application starts [syslogOperationsStatus is ''started'' ] or the syslog application stops [syslogOperationsStatus is ''suspended'' or ''stopped'']. The value of syslogOperationsStatus will be the new status of the syslog application after the change. The syslog application corresponding to the notification will be identified by the syslogOperationsIndex instance identifier of the objects in the notification." ::= 1 syslogOperationsGroup OBJECT IDENTIFIER ::= { syslogGroups 1 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects providing message related -- statistics. -- objects -- syslogOperationsMsgsReceived, syslogOperationsMsgsTransmitted, -- syslogOperationsMsgsRelayed, syslogOperationsMsgsDropped, -- syslogOperationsMsgsMalFormed, syslogOperationsMsgsDiscarded, -- syslogOperationsLastMsgRecdTime, -- syslogOperationsLastMsgTransmittedTime, -- syslogOperationsStartTime, syslogOperationsLastError, -- syslogOperationsLastErrorTime, syslogOperationsRunIndex, -- syslogOperationsCounterDiscontinuityTime, -- syslogOperationsStatus syslogControlGroup OBJECT IDENTIFIER ::= { syslogGroups 2 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects representing the run time parameters -- for the syslog applications. -- objects -- syslogControlDescr, syslogControlRoles, -- syslogControlBindAddrType, syslogControlBindAddr, -- syslogControlEncapsulation, syslogControlBindPort, -- syslogControlMaxMessageSize, syslogControlConfFileName, -- syslogControlStorageType, syslogControlRowStatus syslogPriorityGroup OBJECT IDENTIFIER ::= { syslogGroups 3 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects representing the priority -- groupings of syslog messages. -- objects -- syslogPriorityDescr, syslogPriorityDestinationIndex, -- syslogPriorityStorageType, syslogPriorityRowStatus syslogRelayGroup OBJECT IDENTIFIER ::= { syslogGroups 4 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- A collection of objects representing the relay -- destinations for syslog messages. -- objects -- syslogRelayDescr, syslogRelayAddrType, syslogRelayAddr, -- syslogRelayPort, syslogRelayEncapsulation, -- syslogRelayMsgsRelayed, syslogRelayCounterDiscontinuityTime, -- syslogRelayStorageType, syslogRelayRowStatus syslogNotificationGroup OBJECT IDENTIFIER ::= { syslogGroups 5 } -- NOTIFICATION-GROUP -- Status -- mandatory -- Descr -- A collection of notifications about the operational -- state of a syslog application. -- notifications -- syslogStatusChanged syslogFullCompliance1 OBJECT IDENTIFIER ::= { syslogCompliances 1 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities which -- implement the SYSLOG-MIB with support for writable -- objects and notifications. Such an implementation can -- be both monitored and configured via SNMP. It can -- also send notifications about change in the -- operational status of the syslog application. -- Module -- >>current<< -- MandGroup -- syslogNotificationGroup -- MandGroup -- syslogOperationsGroup -- MandGroup -- syslogControlGroup -- MandGroup -- syslogPriorityGroup -- MandGroup -- syslogRelayGroup syslogFullCompliance2 OBJECT IDENTIFIER ::= { syslogCompliances 2 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities which -- implement the SYSLOG-MIB with support for writable -- objects. Such an implementation can -- be both monitored and configured via SNMP. -- Module -- >>current<< -- MandGroup -- syslogOperationsGroup -- MandGroup -- syslogControlGroup -- MandGroup -- syslogPriorityGroup -- MandGroup -- syslogRelayGroup syslogFullCompliance3 OBJECT IDENTIFIER ::= { syslogCompliances 3 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities which -- implement the SYSLOG-MIB with support for writable -- objects but without support for the objects in -- syslogPriorityGroup and syslogRelayGroup. Such an -- implementation can be both monitored and configured -- via SNMP. -- Module -- >>current<< -- MandGroup -- syslogOperationsGroup -- MandGroup -- syslogControlGroup syslogReadOnlyCompliance1 OBJECT IDENTIFIER ::= { syslogCompliances 4 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities which -- implement the syslog MIB without support -- for read-write (i.e. in read-only mode). It can -- also send notifications about change in the -- operational status of the syslog application. -- Module -- >>current<< -- MandGroup -- syslogNotificationGroup -- MandGroup -- syslogOperationsGroup -- MandGroup -- syslogControlGroup -- MandGroup -- syslogPriorityGroup -- MandGroup -- syslogRelayGroup -- ObjVar -- syslogControlDescr -- ObjVar -- syslogControlRoles -- ObjVar -- syslogControlBindAddrType -- ObjVar -- syslogControlBindAddr -- ObjVar -- syslogControlBindPort -- ObjVar -- syslogControlEncapsulation -- ObjVar -- syslogControlMaxMessageSize -- ObjVar -- syslogControlConfFileName -- ObjVar -- syslogControlStorageType -- ObjVar -- syslogControlRowStatus syslogReadOnlyCompliance2 OBJECT IDENTIFIER ::= { syslogCompliances 5 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities which -- implement the syslog MIB without support -- for read-write (i.e. in read-only mode). -- Module -- >>current<< -- MandGroup -- syslogOperationsGroup -- MandGroup -- syslogControlGroup -- MandGroup -- syslogPriorityGroup -- MandGroup -- syslogRelayGroup -- ObjVar -- syslogControlDescr -- ObjVar -- syslogControlRoles -- ObjVar -- syslogControlBindAddrType -- ObjVar -- syslogControlBindAddr -- ObjVar -- syslogControlBindPort -- ObjVar -- syslogControlEncapsulation -- ObjVar -- syslogControlMaxMessageSize -- ObjVar -- syslogControlConfFileName -- ObjVar -- syslogControlStorageType -- ObjVar -- syslogControlRowStatus -- ObjVar -- syslogPriorityDescr -- ObjVar -- syslogPriorityDestinationIndex -- ObjVar -- syslogPriorityStorageType -- ObjVar -- syslogPriorityRowStatus -- ObjVar -- syslogRelayDescr -- ObjVar -- syslogRelayAddrType -- ObjVar -- syslogRelayAddr -- ObjVar -- syslogRelayPort -- ObjVar -- syslogRelayEncapsulation -- ObjVar -- syslogRelayStorageType -- ObjVar -- syslogRelayRowStatus syslogReadOnlyCompliance3 OBJECT IDENTIFIER ::= { syslogCompliances 6 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities which -- implement the syslog MIB without support -- for read-write (i.e. in read-only mode) and without -- support for the objects in syslogRelayGroup and -- syslogPriorityGroup. -- Module -- >>current<< -- MandGroup -- syslogOperationsGroup -- MandGroup -- syslogControlGroup -- ObjVar -- syslogControlDescr -- ObjVar -- syslogControlRoles -- ObjVar -- syslogControlBindAddrType -- ObjVar -- syslogControlBindAddr -- ObjVar -- syslogControlBindPort -- ObjVar -- syslogControlEncapsulation -- ObjVar -- syslogControlMaxMessageSize -- ObjVar -- syslogControlConfFileName -- ObjVar -- syslogControlStorageType -- ObjVar -- syslogControlRowStatus syslogNotificationCompliance OBJECT IDENTIFIER ::= { syslogCompliances 7 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities -- which implement the SYSLOG-MIB and support -- only notifications about change in the -- operational status of a syslog application. -- Module -- >>current<< -- MandGroup -- syslogNotificationGroup END