-- MIB file created 09-Dec-2011 21:20:36, by -- SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com VDSL2-LINE-MIB DEFINITIONS ::= BEGIN -- From file: "VDSL2-LINE-MIB.my" -- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T" IMPORTS transmission FROM SNMPv2-SMI-v1 ifIndex FROM IF-MIB TruthValue, RowStatus FROM SNMPv2-TC-v1 SnmpAdminString FROM SNMP-FRAMEWORK-MIB HCPerfIntervalThreshold, HCPerfTimeElapsed FROM HC-PerfHist-TC-MIB Xdsl2Unit, Xdsl2Direction, Xdsl2Band, Xdsl2TransmissionModeType, Xdsl2RaMode, Xdsl2InitResult, Xdsl2OperationModes, Xdsl2PowerMngState, Xdsl2ConfPmsForce, Xdsl2LinePmMode, Xdsl2LineLdsf, Xdsl2LdsfResult, Xdsl2LineBpsc, Xdsl2BpscResult, Xdsl2LineReset, Xdsl2SymbolProtection, Xdsl2SymbolProtection8, Xdsl2MaxBer, Xdsl2ChInitPolicy, Xdsl2ScMaskDs, Xdsl2ScMaskUs, Xdsl2CarMask, Xdsl2RfiBands, Xdsl2PsdMaskDs, Xdsl2PsdMaskUs, Xdsl2Tssi, Xdsl2LastTransmittedState, Xdsl2LineStatus, Xdsl2ChInpReport, Xdsl2ChAtmStatus, Xdsl2ChPtmStatus, Xdsl2UpboKLF, Xdsl2BandUs, Xdsl2LineProfiles, Xdsl2LineUs0Mask, Xdsl2LineClassMask, Xdsl2LineLimitMask, Xdsl2LineUs0Disable, Xdsl2LinePsdMaskSelectUs, Xdsl2LineCeFlag, Xdsl2LineSnrMode, Xdsl2LineTxRefVnDs, Xdsl2LineTxRefVnUs, Xdsl2BitsAlloc, Xdsl2MrefPsdDs, Xdsl2MrefPsdUs FROM VDSL2-LINE-TC-MIB Counter, Gauge FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215; vdsl2MIB OBJECT IDENTIFIER ::= { transmission 251 } -- MODULE-IDENTITY -- LastUpdated -- 200909300000Z -- OrgName -- ADSLMIB Working Group -- ContactInfo -- WG-email: adslmib@ietf.org -- Info: https://www1.ietf.org/mailman/listinfo/adslmib -- -- Chair: Mike Sneed -- Sand Channel Systems -- Postal: P.O. Box 37324 -- Raleigh NC 27627-732 -- Email: sneedmike@hotmail.com -- Phone: +1 206 600 7022 -- -- Co-Chair: Menachem Dodge -- ECI Telecom Ltd. -- Postal: 30 Hasivim St. -- Petach Tikva 49517, -- Israel. -- Email: mbdodge@ieee.org -- Phone: +972 3 926 8421 -- -- Co-editor: Moti Morgenstern -- ECI Telecom Ltd. -- Postal: 30 Hasivim St. -- Petach Tikva 49517, -- Israel. -- Email: moti.morgenstern@ecitele.com -- Phone: +972 3 926 6258 -- -- Co-editor: Scott Baillie -- NEC Australia -- Postal: 649-655 Springvale Road, -- Mulgrave, Victoria 3170, -- Australia. -- Email: scott.baillie@nec.com.au -- Phone: +61 3 9264 3986 -- -- Co-editor: Umberto Bonollo -- NEC Australia -- Postal: 649-655 Springvale Road, -- Mulgrave, Victoria 3170, -- Australia. -- Email: umberto.bonollo@nec.com.au -- Phone: +61 3 9264 3385 -- Descr -- -- This document defines a Management Information Base (MIB) -- module for use with network management protocols in the -- Internet community for the purpose of managing VDSL2, ADSL, -- ADSL2, and ADSL2+ lines. -- -- The MIB module described in RFC 2662 [RFC2662] defines -- objects used for managing Asymmetric Bit-Rate DSL (ADSL) -- -- interfaces per [T1E1.413], [G.992.1], and [G.992.2]. -- These object descriptions are based upon the specifications -- for the ADSL Embedded Operations Channel (EOC) as defined -- in American National Standards Institute (ANSI) T1E1.413 -- [T1E1.413] and International Telecommunication Union (ITU-T) -- G.992.1 [G.992.1] and G.992.2 [G.992.2]. -- -- The MIB module described in RFC 4706 [RFC4706] defines -- objects used for managing ADSL2 interfaces per [G.992.3] -- and [G.992.4], and ADSL2+ interfaces per [G.992.5]. That MIB -- is also capable of managing ADSL interfaces per [T1E1.413], -- [G.992.1], and [G.992.2]. -- -- This document does not obsolete RFC 2662 [RFC2662] or -- RFC 4706 [RFC4706], but rather provides a more comprehensive -- management model that manages VDSL2 interfaces per G.993.2 -- [G.993.2] as well as ADSL, ADSL2, and ADSL2+ technologies -- per T1E1.413, G.992.1, G.992.2, G.992.3, G.992.4, and -- G.992.5 -- ([T1E1.413], [G.992.1], [G.992.2], [G.992.3], [G.992.4], and -- [G.992.5], respectively). -- -- Additionally, the management framework for VDSL2 lines -- specified by the Digital Subscriber Line Forum -- (DSLF) has been taken into consideration [TR-129]. That -- framework is based on the ITU-T G.997.1 standard [G.997.1] and -- its amendment 1 [G.997.1-Am1]. -- -- The MIB module is located in the MIB tree under MIB 2 -- transmission, as discussed in the MIB-2 Integration (RFC 2863 -- [RFC2863]) section of this document. -- -- Copyright (c) 2009 IETF Trust and the persons identified -- as authors of the code. All rights reserved. -- -- Redistribution and use in source and binary forms, with -- or without modification, are permitted provided that the -- following conditions are met: -- -- - Redistributions of source code must retain the above -- copyright notice, this list of conditions and the -- following disclaimer. -- -- - Redistributions in binary form must reproduce the above -- copyright notice, this list of conditions and the -- following disclaimer in the documentation and/or other -- materials provided with the distribution. -- -- - Neither the name of Internet Society, IETF or IETF Trust, -- nor the names of specific contributors, may be used to -- endorse or promote products derived from this software -- without specific prior written permission. -- -- THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND -- CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, -- INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF -- MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE -- DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR -- CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, -- SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT -- NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; -- LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) -- HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -- CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE -- OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS -- SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. -- -- This version of this MIB module is part of RFC 5650; -- see the RFC itself for full legal notices. -- RevDate -- 200909300000Z -- RevDescr -- Initial version, published as RFC 5650. xdsl2Notifications OBJECT IDENTIFIER ::= { vdsl2MIB 0 } xdsl2Objects OBJECT IDENTIFIER ::= { vdsl2MIB 1 } xdsl2Conformance OBJECT IDENTIFIER ::= { vdsl2MIB 2 } xdsl2Line OBJECT IDENTIFIER ::= { xdsl2Objects 1 } xdsl2Status OBJECT IDENTIFIER ::= { xdsl2Objects 2 } xdsl2Inventory OBJECT IDENTIFIER ::= { xdsl2Objects 3 } xdsl2PM OBJECT IDENTIFIER ::= { xdsl2Objects 4 } xdsl2Profile OBJECT IDENTIFIER ::= { xdsl2Objects 5 } xdsl2Scalar OBJECT IDENTIFIER ::= { xdsl2Objects 6 } xdsl2PMLine OBJECT IDENTIFIER ::= { xdsl2PM 1 } xdsl2PMChannel OBJECT IDENTIFIER ::= { xdsl2PM 2 } xdsl2ProfileLine OBJECT IDENTIFIER ::= { xdsl2Profile 1 } xdsl2ProfileChannel OBJECT IDENTIFIER ::= { xdsl2Profile 2 } xdsl2ProfileAlarmConf OBJECT IDENTIFIER ::= { xdsl2Profile 3 } xdsl2ScalarSC OBJECT IDENTIFIER ::= { xdsl2Scalar 1 } xdsl2Groups OBJECT IDENTIFIER ::= { xdsl2Conformance 1 } xdsl2Compliances OBJECT IDENTIFIER ::= { xdsl2Conformance 2 } xdsl2LineTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineTable contains configuration, command and status parameters of the VDSL2/ADSL/ADSL2 or ADSL2+ line. Several objects in this table MUST be maintained in a persistent manner." ::= { xdsl2Line 1 } xdsl2LineEntry OBJECT-TYPE SYNTAX Xdsl2LineEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The index of this table is an interface index where the interface has an ifType of vdsl2(251)." INDEX { ifIndex } ::= { xdsl2LineTable 1 } Xdsl2LineEntry ::= SEQUENCE { xdsl2LineConfTemplate SnmpAdminString, xdsl2LineConfFallbackTemplate SnmpAdminString, xdsl2LineAlarmConfTemplate SnmpAdminString, xdsl2LineCmndConfPmsf Xdsl2ConfPmsForce, xdsl2LineCmndConfLdsf Xdsl2LineLdsf, xdsl2LineCmndConfLdsfFailReason Xdsl2LdsfResult, xdsl2LineCmndConfBpsc Xdsl2LineBpsc, xdsl2LineCmndConfBpscFailReason Xdsl2BpscResult, xdsl2LineCmndConfBpscRequests Counter, xdsl2LineCmndAutomodeColdStart TruthValue, xdsl2LineCmndConfReset Xdsl2LineReset, xdsl2LineStatusActTemplate SnmpAdminString, xdsl2LineStatusXtuTransSys Xdsl2TransmissionModeType, xdsl2LineStatusPwrMngState Xdsl2PowerMngState, xdsl2LineStatusInitResult Xdsl2InitResult, xdsl2LineStatusLastStateDs Xdsl2LastTransmittedState, xdsl2LineStatusLastStateUs Xdsl2LastTransmittedState, xdsl2LineStatusXtur Xdsl2LineStatus, xdsl2LineStatusXtuc Xdsl2LineStatus, xdsl2LineStatusAttainableRateDs Gauge, xdsl2LineStatusAttainableRateUs Gauge, xdsl2LineStatusActPsdDs INTEGER, xdsl2LineStatusActPsdUs INTEGER, xdsl2LineStatusActAtpDs INTEGER, xdsl2LineStatusActAtpUs INTEGER, xdsl2LineStatusActProfile Xdsl2LineProfiles, xdsl2LineStatusActLimitMask Xdsl2LineLimitMask, xdsl2LineStatusActUs0Mask Xdsl2LineUs0Mask, xdsl2LineStatusActSnrModeDs Xdsl2LineSnrMode, xdsl2LineStatusActSnrModeUs Xdsl2LineSnrMode, xdsl2LineStatusElectricalLength Gauge, xdsl2LineStatusTssiDs Xdsl2Tssi, xdsl2LineStatusTssiUs Xdsl2Tssi, xdsl2LineStatusMrefPsdDs Xdsl2MrefPsdDs, xdsl2LineStatusMrefPsdUs Xdsl2MrefPsdUs, xdsl2LineStatusTrellisDs TruthValue, xdsl2LineStatusTrellisUs TruthValue, xdsl2LineStatusActualCe Gauge } xdsl2LineConfTemplate OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the xDSL2 Line Configuration Template Table, xdsl2LineConfTemplateTable, that applies for this line. This object MUST be maintained in a persistent manner." REFERENCE "DSL Forum TR-129, paragraph #5.1" DEFVAL { "DEFVAL" } ::= { xdsl2LineEntry 1 } xdsl2LineConfFallbackTemplate OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to identify the template that will be used if the xDSL2 line fails to operate using the primary template. The primary template is identified using the xdsl2LineConfTemplate object. For example, a xDSL2 line may fall back to a template with a lower rate if the rate specified in the primary template cannot be achieved. The value of this object identifies a row in the xDSL2 Line Configuration Template Table, xdsl2LineConfTemplateTable. Any row in the xdsl2LineConfTemplateTable table may be used as a fall-back template. If the xDSL2 line fails to operate using the fall-back template, then the primary template should be retried. The xTU-C should continue to alternate between the primary and fall-back templates until one of them succeeds. If the value of this object is a zero-length string, then no fall-back template is defined and only the primary template will be used. Note that implementation of this object is not mandatory. If this object is not supported, any attempt to modify this object should result in the SET request being rejected. This object MUST be maintained in a persistent manner." ::= { xdsl2LineEntry 2 } xdsl2LineAlarmConfTemplate OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the xDSL2 Line Alarm Configuration Template Table, xdsl2LineAlarmConfTemplateTable, which applies to this line. This object MUST be maintained in a persistent manner." REFERENCE "DSL Forum TR-129, paragraph #5.1" DEFVAL { "DEFVAL" } ::= { xdsl2LineEntry 3 } xdsl2LineCmndConfPmsf OBJECT-TYPE SYNTAX Xdsl2ConfPmsForce -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- l3toL0(0), -- l0toL2(2), -- l0orL2toL3(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Power management state forced (PMSF). Defines the line states to be forced by the near-end xTU on this line. This object MUST be maintained in a persistent manner." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.3 (PMSF)" DEFVAL { l3toL0 } ::= { xdsl2LineEntry 4 } xdsl2LineCmndConfLdsf OBJECT-TYPE SYNTAX Xdsl2LineLdsf -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- inhibit(0), -- force(1) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Loop diagnostic state forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end xTU of this line. Note that a loop diagnostic may be initiated by the far-end xTU at any time. Only when the xdsl2LineStatusPwrMngState object is in the 'l3' state and the xdsl2LineCmndConfPmsf object is in the 'l0orL2toL3' state, can the line be forced into loop diagnostic mode procedures. Upon successful completion of the loop diagnostic mode procedures, the Access Node shall set this object to 'inhibit', and xdsl2LineStatusPwrMngState will remain in the 'l3' state. The loop diagnostic data shall be available at least until xdsl2LineCmndConfPmsf is set to the 'l3toL0' state. The results of the loop diagnostic procedure are stored in the tables xdsl2SCStatusTable, xdsl2SCStatusBandTable, and xdsl2SCStatusSegmentTable. The status of the loop diagnostic procedure is indicated by xdsl2LineCmndConfLdsfFailReason. As long as loop diagnostic procedures are not completed successfully, attempts shall be made to do so, until the loop diagnostic mode is no longer forced on the line through this configuration parameter." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.8 (LDSF)" DEFVAL { inhibit } ::= { xdsl2LineEntry 5 } xdsl2LineCmndConfLdsfFailReason OBJECT-TYPE SYNTAX Xdsl2LdsfResult -- Rsyntax INTEGER { -- none(1), -- success(2), -- inProgress(3), -- unsupported(4), -- cannotRun(5), -- aborted(6), -- failed(7), -- illegalMode(8), -- adminUp(9), -- tableFull(10), -- noResources(11) -- } ACCESS read-only STATUS mandatory DESCRIPTION "The status of the most recent occasion when the loop diagnostics state forced (LDSF) command was issued for the associated line." DEFVAL { none } ::= { xdsl2LineEntry 6 } xdsl2LineCmndConfBpsc OBJECT-TYPE SYNTAX Xdsl2LineBpsc -- Rsyntax INTEGER { -- idle(1), -- measure(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Request a bits-per-subcarrier measurement to be made. A request for a bits-per-subcarrier measurement is made by setting this object to the value of 'measure'. Upon completion of the measurement request, the Access Node shall set this object to 'idle'. The SNMP agent should allow initiating a bits-per-subcarrier measurement process only if there is no other bits-per-subcarrier measurement already running, and respond with an SNMP error (e.g., wrongValue) otherwise. Note that a bits-per-subcarrier measurement is also performed during a line diagnostic procedure. This object provides an additional mechanism to fetch the bits-per-subcarrier data. This additional mechanism is provided so that bits-per-subcarrier data may be fetched without forcing the line into no power state. This is useful because the bits-per-subcarrier allocation may be adjusted at show time due to rate adaption and bit swapping. The implementation of this additional mechanism for measuring bits per subcarrier is not mandatory. The results of the bits-per-subcarrier measurement are stored in xdsl2LineSegmentTable. The status of the bits-per-subcarrier measurement is indicated by xdsl2LineCmndConfBpscFailReason." DEFVAL { idle } ::= { xdsl2LineEntry 7 } xdsl2LineCmndConfBpscFailReason OBJECT-TYPE SYNTAX Xdsl2BpscResult -- Rsyntax INTEGER { -- none(1), -- success(2), -- inProgress(3), -- unsupported(4), -- failed(5), -- noResources(6) -- } ACCESS read-only STATUS mandatory DESCRIPTION "The status of the most recent bits-per-subcarrier measurement request issued for the associated line." DEFVAL { none } ::= { xdsl2LineEntry 8 } xdsl2LineCmndConfBpscRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Measurement request counter. This counter is incremented by one every time a request for a bits-per-subcarrier measurement is made. A measurement request is made by modifying the xdsl2LineCmndConfBpsc object from idle(1) to the value measure(2). The measurement results may be very large and will not fit into a single PDU; hence, multiple SNMP GET requests may be required to fetch the measurement results. Because the measurement results cannot be fetched atomically, it is possible for a second manager to start a new measurement before a first manager has fetched all of its results. An SNMP manager can use this object to ensure that the measurement results retrieved using one or more GET requests all belong to the measurement initiated by that manager. The following steps are suggested in order for the SNMP manager to initiate the bits-per-subcarrier measurement: 1. Wait for xdsl2LineCmndConfBpsc value to be idle(1). 2. Perform an SNMP GET for xdsl2LineCmndConfBpscRequests. 3. Wait a short delay (4 -> 8 seconds). 4. Perform an SNMP SET on xdsl2LineCmndConfBpsc with the value measure(2). 5. If step 4 returns an error, then go to step 1. 6. Wait for xdsl2LineCmndConfBpsc value to be idle(1). 7. Fetch measurement results using one or more GET PDUs. 8. Perform an SNMP GET for xdsl2LineCmndConfBpscRequests. 9. Compute the difference between the two values of xdsl2LineCmndConfBpscRequests. If the value is one, then the results are valid, else go to step 1." ::= { xdsl2LineEntry 9 } xdsl2LineCmndAutomodeColdStart OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Automode cold start forced. This parameter is defined in order to improve testing of the performance of xTUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' to indicate a change in loop conditions applied to the devices under the test. The xTUs shall reset any historical information used for automode and for shortening G.994.1 handshake and initialization. Automode is the case where multiple operation-modes are enabled through the xdsl2LConfProfXtuTransSysEna object in the line configuration profile being used for the line, and where the selection of the actual operation-mode depends not only on the common capabilities of both xTUs (as exchanged in G.994.1), but also on achievable data rates under given loop conditions." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.10 (Automode Cold Start Forced)" DEFVAL { false } ::= { xdsl2LineEntry 10 } xdsl2LineCmndConfReset OBJECT-TYPE SYNTAX Xdsl2LineReset -- Rsyntax INTEGER { -- idle(1), -- reset(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Request a line reset to occur. If this object is set to the value of 'reset', then force the line to reset (i.e., the modems will retrain). When the line has successfully reset, the SNMP agent will set the value of this object to 'idle'. Note that the xdsl2LineCmndConfPmsf object will always take precedence over this object. If the xdsl2LineCmndConfPmsf object is set to the value 'l0orL2toL3', then the line MUST NOT return to the Showtime state due to a reset request action performed using this object." DEFVAL { idle } ::= { xdsl2LineEntry 11 } xdsl2LineStatusActTemplate OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "This object is used to identify the template that is currently in use for this line. This object is updated when a successful line initialization occurs. This object indicates if the primary template (xdsl2LineConfTemplate) is in use or the fall-back template (xdsl2LineConfFallbackTemplate) is in use. If the line is not successfully initialized, then the value of this object will be a zero-length string." ::= { xdsl2LineEntry 12 } xdsl2LineStatusXtuTransSys OBJECT-TYPE SYNTAX Xdsl2TransmissionModeType -- Rsyntax OCTET STRING(SIZE(1..8)) -- BITS are: -- ansit1413(0) -- etsi(1) -- g9921PotsNonOverlapped(2) -- g9921PotsOverlapped(3) -- g9921IsdnNonOverlapped(4) -- g9921isdnOverlapped(5) -- g9921tcmIsdnNonOverlapped(6) -- g9921tcmIsdnOverlapped(7) -- g9922potsNonOverlapped(8) -- g9922potsOverlapped(9) -- g9922tcmIsdnNonOverlapped(10) -- g9922tcmIsdnOverlapped(11) -- g9921tcmIsdnSymmetric(12) -- reserved1(13) -- reserved2(14) -- reserved3(15) -- reserved4(16) -- reserved5(17) -- g9923PotsNonOverlapped(18) -- g9923PotsOverlapped(19) -- g9923IsdnNonOverlapped(20) -- g9923isdnOverlapped(21) -- reserved6(22) -- reserved7(23) -- g9924potsNonOverlapped(24) -- g9924potsOverlapped(25) -- reserved8(26) -- reserved9(27) -- g9923AnnexIAllDigNonOverlapped(28) -- g9923AnnexIAllDigOverlapped(29) -- g9923AnnexJAllDigNonOverlapped(30) -- g9923AnnexJAllDigOverlapped(31) -- g9924AnnexIAllDigNonOverlapped(32) -- g9924AnnexIAllDigOverlapped(33) -- g9923AnnexLMode1NonOverlapped(34) -- g9923AnnexLMode2NonOverlapped(35) -- g9923AnnexLMode3Overlapped(36) -- g9923AnnexLMode4Overlapped(37) -- g9923AnnexMPotsNonOverlapped(38) -- g9923AnnexMPotsOverlapped(39) -- g9925PotsNonOverlapped(40) -- g9925PotsOverlapped(41) -- g9925IsdnNonOverlapped(42) -- g9925isdnOverlapped(43) -- reserved10(44) -- reserved11(45) -- g9925AnnexIAllDigNonOverlapped(46) -- g9925AnnexIAllDigOverlapped(47) -- g9925AnnexJAllDigNonOverlapped(48) -- g9925AnnexJAllDigOverlapped(49) -- g9925AnnexMPotsNonOverlapped(50) -- g9925AnnexMPotsOverlapped(51) -- reserved12(52) -- reserved13(53) -- reserved14(54) -- reserved15(55) -- g9932AnnexA(56) -- g9932AnnexB(57) -- g9932AnnexC(58) -- reserved16(59) -- reserved17(60) -- reserved18(61) -- reserved19(62) -- reserved20(63) ACCESS read-only STATUS mandatory DESCRIPTION "The xTU Transmission System (xTS) in use. It is coded in a bitmap representation with one bit set to '1' (the selected coding for the DSL line). This parameter may be derived from the handshaking procedures defined in Recommendation G.994.1. A set of xDSL line transmission modes, with one bit per mode." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.1 (xDSL transmission system)" DEFVAL { '0000000000000000'h } ::= { xdsl2LineEntry 13 } xdsl2LineStatusPwrMngState OBJECT-TYPE SYNTAX Xdsl2PowerMngState -- Rsyntax INTEGER { -- l0(1), -- l1(2), -- l2(3), -- l3(4) -- } ACCESS read-only STATUS mandatory DESCRIPTION "The current power management state." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.5 (Line power management state)" DEFVAL { l3 } ::= { xdsl2LineEntry 14 } xdsl2LineStatusInitResult OBJECT-TYPE SYNTAX Xdsl2InitResult -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- noFail(0), -- configError(1), -- configNotFeasible(2), -- commFail(3), -- noPeerAtu(4), -- otherCause(5) -- } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the result of the last full initialization performed on the line." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.6 (Initialization success/failure cause)" DEFVAL { noFail } ::= { xdsl2LineEntry 15 } xdsl2LineStatusLastStateDs OBJECT-TYPE SYNTAX Xdsl2LastTransmittedState -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- atucG9941(0), -- atucQuiet1(1), -- atucComb1(2), -- atucQuiet2(3), -- atucComb2(4), -- atucIcomb1(5), -- atucLineprob(6), -- atucQuiet3(7), -- atucComb3(8), -- atucIComb2(9), -- atucMsgfmt(10), -- atucMsgpcb(11), -- atucQuiet4(12), -- atucReverb1(13), -- atucTref1(14), -- atucReverb2(15), -- atucEct(16), -- atucReverb3(17), -- atucTref2(18), -- atucReverb4(19), -- atucSegue1(20), -- atucMsg1(21), -- atucReverb5(22), -- atucSegue2(23), -- atucMedley(24), -- atucExchmarker(25), -- atucMsg2(26), -- atucReverb6(27), -- atucSegue3(28), -- atucParams(29), -- atucReverb7(30), -- atucSegue4(31), -- atucShowtime(32), -- aturG9941(100), -- aturQuiet1(101), -- aturComb1(102), -- aturQuiet2(103), -- aturComb2(104), -- aturIcomb1(105), -- aturLineprob(106), -- aturQuiet3(107), -- aturComb3(108), -- aturIcomb2(109), -- aturMsgfmt(110), -- aturMsgpcb(111), -- aturReverb1(112), -- aturQuiet4(113), -- aturReverb2(114), -- aturQuiet5(115), -- aturReverb3(116), -- aturEct(117), -- aturReverb4(118), -- aturSegue1(119), -- aturReverb5(120), -- aturSegue2(121), -- aturMsg1(122), -- aturMedley(123), -- aturExchmarker(124), -- aturMsg2(125), -- aturReverb6(126), -- aturSegue3(127), -- aturParams(128), -- aturReverb7(129), -- aturSegue4(130), -- aturShowtime(131), -- vtucG9941(200), -- vtucQuiet1(201), -- vtucChDiscov1(202), -- vtucSynchro1(203), -- vtucPilot1(204), -- vtucQuiet2(205), -- vtucPeriodic1(206), -- vtucSynchro2(207), -- vtucChDiscov2(208), -- vtucSynchro3(209), -- vtucTraining1(210), -- vtucSynchro4(211), -- vtucPilot2(212), -- vtucTeq(213), -- vtucEct(214), -- vtucPilot3(215), -- vtucPeriodic2(216), -- vtucTraining2(217), -- vtucSynchro5(218), -- vtucMedley(219), -- vtucSynchro6(220), -- vtucShowtime(221), -- vturG9941(300), -- vturQuiet1(301), -- vturChDiscov1(302), -- vturSynchro1(303), -- vturLineprobe(304), -- vturPeriodic1(305), -- vturSynchro2(306), -- vturChDiscov2(307), -- vturSynchro3(308), -- vturQuiet2(309), -- vturTraining1(310), -- vturSynchro4(311), -- vturTeq(312), -- vturQuiet3(313), -- vturEct(314), -- vturPeriodic2(315), -- vturTraining2(316), -- vturSynchro5(317), -- vturMedley(318), -- vturSynchro6(319), -- vturShowtime(320) -- } ACCESS read-only STATUS mandatory DESCRIPTION "The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.7 (Downstream last transmitted state)" DEFVAL { atucG9941 } ::= { xdsl2LineEntry 16 } xdsl2LineStatusLastStateUs OBJECT-TYPE SYNTAX Xdsl2LastTransmittedState -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- atucG9941(0), -- atucQuiet1(1), -- atucComb1(2), -- atucQuiet2(3), -- atucComb2(4), -- atucIcomb1(5), -- atucLineprob(6), -- atucQuiet3(7), -- atucComb3(8), -- atucIComb2(9), -- atucMsgfmt(10), -- atucMsgpcb(11), -- atucQuiet4(12), -- atucReverb1(13), -- atucTref1(14), -- atucReverb2(15), -- atucEct(16), -- atucReverb3(17), -- atucTref2(18), -- atucReverb4(19), -- atucSegue1(20), -- atucMsg1(21), -- atucReverb5(22), -- atucSegue2(23), -- atucMedley(24), -- atucExchmarker(25), -- atucMsg2(26), -- atucReverb6(27), -- atucSegue3(28), -- atucParams(29), -- atucReverb7(30), -- atucSegue4(31), -- atucShowtime(32), -- aturG9941(100), -- aturQuiet1(101), -- aturComb1(102), -- aturQuiet2(103), -- aturComb2(104), -- aturIcomb1(105), -- aturLineprob(106), -- aturQuiet3(107), -- aturComb3(108), -- aturIcomb2(109), -- aturMsgfmt(110), -- aturMsgpcb(111), -- aturReverb1(112), -- aturQuiet4(113), -- aturReverb2(114), -- aturQuiet5(115), -- aturReverb3(116), -- aturEct(117), -- aturReverb4(118), -- aturSegue1(119), -- aturReverb5(120), -- aturSegue2(121), -- aturMsg1(122), -- aturMedley(123), -- aturExchmarker(124), -- aturMsg2(125), -- aturReverb6(126), -- aturSegue3(127), -- aturParams(128), -- aturReverb7(129), -- aturSegue4(130), -- aturShowtime(131), -- vtucG9941(200), -- vtucQuiet1(201), -- vtucChDiscov1(202), -- vtucSynchro1(203), -- vtucPilot1(204), -- vtucQuiet2(205), -- vtucPeriodic1(206), -- vtucSynchro2(207), -- vtucChDiscov2(208), -- vtucSynchro3(209), -- vtucTraining1(210), -- vtucSynchro4(211), -- vtucPilot2(212), -- vtucTeq(213), -- vtucEct(214), -- vtucPilot3(215), -- vtucPeriodic2(216), -- vtucTraining2(217), -- vtucSynchro5(218), -- vtucMedley(219), -- vtucSynchro6(220), -- vtucShowtime(221), -- vturG9941(300), -- vturQuiet1(301), -- vturChDiscov1(302), -- vturSynchro1(303), -- vturLineprobe(304), -- vturPeriodic1(305), -- vturSynchro2(306), -- vturChDiscov2(307), -- vturSynchro3(308), -- vturQuiet2(309), -- vturTraining1(310), -- vturSynchro4(311), -- vturTeq(312), -- vturQuiet3(313), -- vturEct(314), -- vturPeriodic2(315), -- vturTraining2(316), -- vturSynchro5(317), -- vturMedley(318), -- vturSynchro6(319), -- vturShowtime(320) -- } ACCESS read-only STATUS mandatory DESCRIPTION "The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.8 (Upstream last transmitted state)" DEFVAL { aturG9941 } ::= { xdsl2LineEntry 17 } xdsl2LineStatusXtur OBJECT-TYPE SYNTAX Xdsl2LineStatus -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- noDefect(0) -- lossOfFraming(1) -- lossOfSignal(2) -- lossOfPower(3) -- initFailure(4) ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current state (existing failures) of the xTU-R. This is a bitmap of possible conditions." REFERENCE "ITU-T G.997.1, paragraph #7.1.1.2 (Line far-end failures)" DEFVAL { '80'h } ::= { xdsl2LineEntry 18 } xdsl2LineStatusXtuc OBJECT-TYPE SYNTAX Xdsl2LineStatus -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- noDefect(0) -- lossOfFraming(1) -- lossOfSignal(2) -- lossOfPower(3) -- initFailure(4) ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current state (existing failures) of the xTU-C. This is a bitmap of possible conditions." REFERENCE "ITU-T G.997.1, paragraph #7.1.1.1 (Line near-end failures)" DEFVAL { '80'h } ::= { xdsl2LineEntry 19 } xdsl2LineStatusAttainableRateDs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-only STATUS mandatory DESCRIPTION "Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the xTU-C transmitter and the xTU-R receiver, coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.19 (ATTNDRds)" DEFVAL { 0 } ::= { xdsl2LineEntry 20 } xdsl2LineStatusAttainableRateUs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-only STATUS mandatory DESCRIPTION "Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the xTU-R transmitter and the xTU-C receiver, coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.20 (ATTNDRus)" DEFVAL { 0 } ::= { xdsl2LineEntry 21 } xdsl2LineStatusActPsdDs OBJECT-TYPE SYNTAX INTEGER(-900..0|2147483647) -- Units -- 0.1 dBm/Hz ACCESS read-only STATUS mandatory DESCRIPTION "Actual Power Spectral Density (PSD) Downstream. The average downstream transmit PSD over the subcarriers used for downstream. It ranges from -900 to 0 units of 0.1 dBm/Hz (physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.21 (ACTPSDds)" DEFVAL { 2147483647 } ::= { xdsl2LineEntry 22 } xdsl2LineStatusActPsdUs OBJECT-TYPE SYNTAX INTEGER(-900..0|2147483647) -- Units -- 0.1 dBm/Hz ACCESS read-only STATUS mandatory DESCRIPTION "Actual Power Spectral Density (PSD) Upstream. The average upstream transmit PSD over the subcarriers used for upstream. It ranges from -900 to 0 units of 0.1 dBm/Hz (physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.22 (ACTPSDus)" DEFVAL { 2147483647 } ::= { xdsl2LineEntry 23 } xdsl2LineStatusActAtpDs OBJECT-TYPE SYNTAX INTEGER(-310..310|2147483647) -- Units -- 0.1 dBm ACCESS read-only STATUS mandatory DESCRIPTION "Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the xTU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dBm (physical values are -31 to 31 dBm). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.24 (ACTATPds)" DEFVAL { 2147483647 } ::= { xdsl2LineEntry 24 } xdsl2LineStatusActAtpUs OBJECT-TYPE SYNTAX INTEGER(-310..310|2147483647) -- Units -- 0.1 dBm ACCESS read-only STATUS mandatory DESCRIPTION "Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the xTU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dBm (physical values are -31 to 31 dBm). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.25 (ACTATPus)" DEFVAL { 2147483647 } ::= { xdsl2LineEntry 25 } xdsl2LineStatusActProfile OBJECT-TYPE SYNTAX Xdsl2LineProfiles -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- profile8a(0) -- profile8b(1) -- profile8c(2) -- profile8d(3) -- profile12a(4) -- profile12b(5) -- profile17a(6) -- profile30a(7) ACCESS read-only STATUS mandatory DESCRIPTION "The G.993.2 profile in use. The configuration parameter xdsl2LConfProfProfiles defines the set of allowed G.993.2 profiles. This parameter indicates the profile in use on this line. This parameter may be derived from the handshaking procedures defined in ITU-T Recommendation G.994.1." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.2 (VDSL2 Profile)" DEFVAL { '00'h } ::= { xdsl2LineEntry 26 } xdsl2LineStatusActLimitMask OBJECT-TYPE SYNTAX Xdsl2LineLimitMask -- Rsyntax OCTET STRING(SIZE(1..8)) -- BITS are: -- profile8Limit1(0) -- profile8Limit2(1) -- profile8Limit3(2) -- profile8Limit4(3) -- profile8Limit5(4) -- profile8Limit6(5) -- profile8Limit7(6) -- profile8Limit8(7) -- profile8Limit9(8) -- profile8Limit10(9) -- profile8Limit11(10) -- profile8Limit12(11) -- profile8Limit13(12) -- profile8Limit14(13) -- profile8Limit15(14) -- profile8Limit16(15) -- profile12Limit1(16) -- profile12Limit2(17) -- profile12Limit3(18) -- profile12Limit4(19) -- profile12Limit5(20) -- profile12Limit6(21) -- profile12Limit7(22) -- profile12Limit8(23) -- profile12Limit9(24) -- profile12Limit10(25) -- profile12Limit11(26) -- profile12Limit12(27) -- profile12Limit13(28) -- profile12Limit14(29) -- profile12Limit15(30) -- profile12Limit16(31) -- profile17Limit1(32) -- profile17Limit2(33) -- profile17Limit3(34) -- profile17Limit4(35) -- profile17Limit5(36) -- profile17Limit6(37) -- profile17Limit7(38) -- profile17Limit8(39) -- profile17Limit9(40) -- profile17Limit10(41) -- profile17Limit11(42) -- profile17Limit12(43) -- profile17Limit13(44) -- profile17Limit14(45) -- profile17Limit15(46) -- profile17Limit16(47) -- profile30Limit1(48) -- profile30Limit2(49) -- profile30Limit3(50) -- profile30Limit4(51) -- profile30Limit5(52) -- profile30Limit6(53) -- profile30Limit7(54) -- profile30Limit8(55) -- profile30Limit9(56) -- profile30Limit10(57) -- profile30Limit11(58) -- profile30Limit12(59) -- profile30Limit13(60) -- profile30Limit14(61) -- profile30Limit15(62) -- profile30Limit16(63) ACCESS read-only STATUS mandatory DESCRIPTION "The Limit PSD mask and band plan in use. The configuration parameter xdsl2LConfProfLimitMask defines the set of allowed G.993.2 limit PSD masks. This parameter indicates the limit PSD mask in use on this line." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.3 (VDSL2 Limit PSD Mask and Band plan)" DEFVAL { '0000000000000000'h } ::= { xdsl2LineEntry 27 } xdsl2LineStatusActUs0Mask OBJECT-TYPE SYNTAX Xdsl2LineUs0Mask -- Rsyntax OCTET STRING(SIZE(1..4)) -- BITS are: -- eu32(0) -- eu36(1) -- eu40(2) -- eu44(3) -- eu48(4) -- eu52(5) -- eu56(6) -- eu60(7) -- eu64(8) -- eu128(9) -- reserved1(10) -- reserved2(11) -- reserved3(12) -- reserved4(13) -- reserved5(14) -- reserved6(15) -- adlu32(16) -- adlu36(17) -- adlu40(18) -- adlu44(19) -- adlu48(20) -- adlu52(21) -- adlu56(22) -- adlu60(23) -- adlu64(24) -- adlu128(25) -- reserved7(26) -- reserved8(27) -- reserved9(28) -- reserved10(29) -- reserved11(30) -- reserved12(31) ACCESS read-only STATUS mandatory DESCRIPTION "The US0 PSD mask in use. The configuration parameter xdsl2LConfProfUs0Mask defines the set of allowed US0 PSD masks. This parameter indicates the US0 PSD mask in use on this line. This parameter may be derived from the handshaking procedures defined in ITU-T Recommendation G.994.1." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.4 (VDSL2 US0 PSD Mask)" DEFVAL { '00000000'h } ::= { xdsl2LineEntry 28 } xdsl2LineStatusActSnrModeDs OBJECT-TYPE SYNTAX Xdsl2LineSnrMode -- Rsyntax INTEGER { -- virtualNoiseDisabled(1), -- virtualNoiseEnabled(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This parameter indicates if the transmitter-referred virtual noise is active on the line in the downstream direction. The configuration parameter xdsl2LConfProfSnrModeDs is used to configure referred virtual noise." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.15 (ACTSNRMODEds)" DEFVAL { virtualNoiseDisabled } ::= { xdsl2LineEntry 29 } xdsl2LineStatusActSnrModeUs OBJECT-TYPE SYNTAX Xdsl2LineSnrMode -- Rsyntax INTEGER { -- virtualNoiseDisabled(1), -- virtualNoiseEnabled(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This parameter indicates if the transmitter-referred virtual noise is active on the line in the upstream direction. The configuration parameter xdsl2LConfProfSnrModeUs is used to configure referred virtual noise." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.18 (ACTSNRMODEus)" DEFVAL { virtualNoiseDisabled } ::= { xdsl2LineEntry 30 } xdsl2LineStatusElectricalLength OBJECT-TYPE SYNTAX Gauge(0..1280) -- Units -- 0.1 dB ACCESS read-only STATUS mandatory DESCRIPTION "This parameter contains the estimated electrical length expressed in dB at 1 MHz, kl0. This is the final electrical length that would have been sent from the VTU-O to VTU-R if the electrical length was not forced by the CO-MIB. The value ranges from 0 to 128 dB in steps of 0.1 dB." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.23 (UPBOKLE)" DEFVAL { 0 } ::= { xdsl2LineEntry 31 } xdsl2LineStatusTssiDs OBJECT-TYPE SYNTAX Xdsl2Tssi -- Rsyntax OCTET STRING(SIZE(0..96)) ACCESS read-only STATUS mandatory DESCRIPTION "The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Downstream)." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.29.5 (TSSpsds)" ::= { xdsl2LineEntry 32 } xdsl2LineStatusTssiUs OBJECT-TYPE SYNTAX Xdsl2Tssi -- Rsyntax OCTET STRING(SIZE(0..96)) ACCESS read-only STATUS mandatory DESCRIPTION "The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Upstream)." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.29.6 (TSSpsus)" ::= { xdsl2LineEntry 33 } xdsl2LineStatusMrefPsdDs OBJECT-TYPE SYNTAX Xdsl2MrefPsdDs -- Rsyntax OCTET STRING(SIZE(0..192)) ACCESS read-only STATUS mandatory DESCRIPTION "The MEDLEY Reference PSD status parameters in the downstream direction expressed as the set of breakpoints exchanged at initialization." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.29.7 (MREFPSDds)" ::= { xdsl2LineEntry 34 } xdsl2LineStatusMrefPsdUs OBJECT-TYPE SYNTAX Xdsl2MrefPsdUs -- Rsyntax OCTET STRING(SIZE(0..128)) ACCESS read-only STATUS mandatory DESCRIPTION "The MEDLEY Reference PSD status parameters in the upstream direction expressed as the set of breakpoints exchanged at initialization." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.29.8 (MREFPSDus)" ::= { xdsl2LineEntry 35 } xdsl2LineStatusTrellisDs OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This parameter reports whether trellis coding is in use in the downstream direction." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.30 (TRELLISds)" DEFVAL { false } ::= { xdsl2LineEntry 36 } xdsl2LineStatusTrellisUs OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This parameter reports whether trellis coding is in use in the upstream direction." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.31 (TRELLISus)" DEFVAL { false } ::= { xdsl2LineEntry 37 } xdsl2LineStatusActualCe OBJECT-TYPE SYNTAX Gauge(2..16) -- Units -- N/32 samples ACCESS read-only STATUS mandatory DESCRIPTION "(ACTUALCE) This parameter reports the cyclic extension used on the line. It is coded as an unsigned integer from 2 to 16 in units of N/32 samples, where 2N is the Inverse Discrete Fourier Transform (IDFT) size." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.32 (ACTUALCE)" DEFVAL { 2 } ::= { xdsl2LineEntry 38 } xdsl2LineSegmentTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineSegmentEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineSegmentTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers. The parameters in this table are updated when a measurement request is made using the xdsl2LineCmndConfBpsc object. Note that a bits-per-subcarrier measurement is also performed during a line diagnostic procedure. This table provides an additional mechanism to fetch the bits-per-subcarrier data. This additional mechanism is provided so that bits-per-subcarrier data may be fetched without forcing the line into no power state. This is useful because the bits-per-subcarrier allocation may be adjusted at Showtime due to rate adaption and bit swapping. The implementation of this additional mechanism for measuring bits per subcarrier is not mandatory." ::= { xdsl2Status 1 } xdsl2LineSegmentEntry OBJECT-TYPE SYNTAX Xdsl2LineSegmentEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineSegmentEntry contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers. Objects in the table refer to NSus and NSds. For G.993.2, the value of NSus and NSds are, respectively, the indices of the highest supported upstream and downstream subcarriers according to the selected implementation profile. For ADSL, NSus is equal to NSCus-1 and NSds is equal to NSCds-1. One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission direction. A third index identifies the specific segment of the subcarriers status addressed." INDEX { ifIndex, xdsl2LineSegmentDirection, xdsl2LineSegment } ::= { xdsl2LineSegmentTable 1 } Xdsl2LineSegmentEntry ::= SEQUENCE { xdsl2LineSegmentDirection Xdsl2Direction, xdsl2LineSegment Gauge, xdsl2LineSegmentBitsAlloc Xdsl2BitsAlloc, xdsl2LineSegmentRowStatus RowStatus } xdsl2LineSegmentDirection OBJECT-TYPE SYNTAX Xdsl2Direction -- Rsyntax INTEGER { -- upstream(1), -- downstream(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The direction of the subcarrier either upstream or downstream." ::= { xdsl2LineSegmentEntry 1 } xdsl2LineSegment OBJECT-TYPE SYNTAX Gauge(1..8) ACCESS not-accessible STATUS mandatory DESCRIPTION "The segment of the subcarriers status information provided by this row. Status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with xdsl2LineSegment=1, the second segment is retrieved with xdsl2LineSegment=2, and so on. When a status parameter is retrieved in n segments where n<8) then, for that parameter, GET operations for the remaining segment numbers (n+1 to 8) will respond with a zero-length OCTET STRING." ::= { xdsl2LineSegmentEntry 2 } xdsl2LineSegmentBitsAlloc OBJECT-TYPE SYNTAX Xdsl2BitsAlloc -- Rsyntax OCTET STRING(SIZE(0..256)) -- Units -- bits ACCESS read-only STATUS mandatory DESCRIPTION "The bits allocation per subcarrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) subcarriers. When more than 512 subcarriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 subcarriers. The second segment is used for the subcarriers 512 to 1023 and so on. The aggregate number of utilized nibbles in the downstream direction (in all segments) depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. The segment number is in xdsl2SCStatusSegment. Nibble i (0 <= i < MIN((NS+1)-(segment-1)*512,512)) in each segment is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream subcarrier j (j=(segement-1)*512+i) has the same amount of bits allocation." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.29.1 (BITSpsds) and paragraph #7.5.1.29.2 (BITSpsus)" ::= { xdsl2LineSegmentEntry 3 } xdsl2LineSegmentRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Row Status. The SNMP agent will create a row in this table for storing the results of a measurement performed on the associated line, if the row does not already exist. The SNMP manager is not permitted to create rows in this table or set the row status to 'notInService'. In the first case, if the SNMP manager tries to create a new row, the SNMP agent responds with the value 'noCreation' in the error status field of the response-PDU. In the latter case, the SNMP agent responds with the value 'wrongValue' in the error status field of the response-PDU. The SNMP agent may have limited resources; therefore, if multiple rows coexist in this table, it may fail to add new rows to this table or allocate memory resources. If that occurs, the SNMP agent responds with the value 'noResources' (for the xdsl2LineCmndConfBpscFailReason object in xdsl2LineTable). The management system (the operator) may delete rows from this table according to any scheme. For example, after retrieving the results. When the SNMP manager deletes any row in this table, the SNMP agent MUST delete all rows in this table that have the same ifIndex value." ::= { xdsl2LineSegmentEntry 4 } xdsl2LineBandTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineBandEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineBandTable contains the, per-band line status parameters of the VDSL2/ADSL/ADSL2 or ADSL2+ line. The parameters in this table are updated at line initialization time and at Showtime." ::= { xdsl2Line 2 } xdsl2LineBandEntry OBJECT-TYPE SYNTAX Xdsl2LineBandEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is a per-band index covering both VDSL2 and ADSL/ADSL2/ADSL2+." INDEX { ifIndex, xdsl2LineBand } ::= { xdsl2LineBandTable 1 } Xdsl2LineBandEntry ::= SEQUENCE { xdsl2LineBand Xdsl2Band, xdsl2LineBandStatusLnAtten Gauge, xdsl2LineBandStatusSigAtten Gauge, xdsl2LineBandStatusSnrMargin INTEGER } xdsl2LineBand OBJECT-TYPE SYNTAX Xdsl2Band -- Rsyntax INTEGER { -- upstream(1), -- downstream(2), -- us0(3), -- ds1(4), -- us1(5), -- ds2(6), -- us2(7), -- ds3(8), -- us3(9), -- ds4(10), -- us4(11) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "Identifies the band(s) associated with this line. For ADSL/ADSL2/ADSL2+, the values 'upstream' and 'downstream' will always be present. For VDSL2, a subset of {'us0', 'ds1', 'us1' ... 'ds4', 'us4' } will always be present, together with rows for 'upstream' and 'downstream', in which only the xdsl2LineBandStatusSnrMargin object is expected to hold a valid (average) measurement." ::= { xdsl2LineBandEntry 1 } xdsl2LineBandStatusLnAtten OBJECT-TYPE SYNTAX Gauge(0..2147483647) -- Units -- 0.1 dB ACCESS read-only STATUS mandatory DESCRIPTION "Line Attenuation. When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers of that band during initialization. When referring to a band in the upstream direction, it is the measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all subcarriers of that band during initialization. Values range from 0 to 1270 in units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.9 (LATNds) and paragraph #7.5.1.10 (LATNus)6" DEFVAL { 2147483646 } ::= { xdsl2LineBandEntry 2 } xdsl2LineBandStatusSigAtten OBJECT-TYPE SYNTAX Gauge(0..2147483647) -- Units -- 0.1 dB ACCESS read-only STATUS mandatory DESCRIPTION "Signal Attenuation. When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers of that band during Showtime. When referring to a band in the upstream direction, it is the measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all subcarriers of that band during Showtime. Values range from 0 to 1270 in units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.11 (SATNds) and paragraph #7.5.1.12 (SATNus)" DEFVAL { 2147483646 } ::= { xdsl2LineBandEntry 3 } xdsl2LineBandStatusSnrMargin OBJECT-TYPE SYNTAX INTEGER(-640..630|2147483646|2147483647) -- Units -- 0.1 dB ACCESS read-only STATUS mandatory DESCRIPTION "SNR Margin is the maximum increase in dB of the noise power received at the xTU (xTU-R for a band in the downstream direction and xTU-C for a band in the upstream direction), such that the BER requirements are met for all bearer channels received at the xTU. Values range from -640 to 630 in units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.13 (SNRMds) and paragraph #7.5.1.14 (SNRMpbds) and paragraph #7.5.1.16 (SNRMus) and paragraph #7.5.1.17 (SNRMpbus)" DEFVAL { 2147483646 } ::= { xdsl2LineBandEntry 4 } xdsl2ChannelStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2ChannelStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2ChannelStatusTable contains status parameters of VDSL2/ADSL/ADSL2 or ADSL2+ channel. This table contains live data from equipment." ::= { xdsl2Status 2 } xdsl2ChannelStatusEntry OBJECT-TYPE SYNTAX Xdsl2ChannelStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the termination unit." INDEX { ifIndex, xdsl2ChStatusUnit } ::= { xdsl2ChannelStatusTable 1 } Xdsl2ChannelStatusEntry ::= SEQUENCE { xdsl2ChStatusUnit Xdsl2Unit, xdsl2ChStatusActDataRate Gauge, xdsl2ChStatusPrevDataRate Gauge, xdsl2ChStatusActDelay Gauge, xdsl2ChStatusActInp Gauge, xdsl2ChStatusInpReport Xdsl2ChInpReport, xdsl2ChStatusNFec Gauge, xdsl2ChStatusRFec Gauge, xdsl2ChStatusLSymb Gauge, xdsl2ChStatusIntlvDepth Gauge, xdsl2ChStatusIntlvBlock Gauge, xdsl2ChStatusLPath Gauge, xdsl2ChStatusAtmStatus Xdsl2ChAtmStatus, xdsl2ChStatusPtmStatus Xdsl2ChPtmStatus } xdsl2ChStatusUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2ChannelStatusEntry 1 } xdsl2ChStatusActDataRate OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-only STATUS mandatory DESCRIPTION "The actual net data rate at which the bearer channel is operating, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The data rate is coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.1 (Actual data rate)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 2 } xdsl2ChStatusPrevDataRate OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-only STATUS mandatory DESCRIPTION "The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fast retrain, DRA or power management transitions, excluding transitions between L0 state and L1 or L2 states. The data rate is coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.2 (Previous data rate)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 3 } xdsl2ChStatusActDelay OBJECT-TYPE SYNTAX Gauge(0..8176) -- Units -- milliseconds ACCESS read-only STATUS mandatory DESCRIPTION "The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. It is coded in ms (rounded to the nearest ms)." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.3 (Actual interleaving delay)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 4 } xdsl2ChStatusActInp OBJECT-TYPE SYNTAX Gauge(0..255) -- Units -- 0.1 symbols ACCESS read-only STATUS mandatory DESCRIPTION "Actual impulse noise protection. This parameter reports the actual impulse noise protection (INP) on the bearer channel in the L0 state. In the L1 or L2 state, the parameter contains the INP in the previous L0 state. For ADSL, this value is computed according to the formula specified in the relevant Recommendation based on the actual framing parameters. For ITU-T Recommendation G.993.2, the method to report this value is according to the INPREPORT parameter. The value is coded in fractions of DMT symbols with a granularity of 0.1 symbols. The range is from 0 to 25.4. The special value of 255 indicates an ACTINP higher than 25.4." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.4 (ACTINP)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 5 } xdsl2ChStatusInpReport OBJECT-TYPE SYNTAX Xdsl2ChInpReport -- Rsyntax INTEGER { -- inpComputedUsingFormula(1), -- inpEstimatedByXtur(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "Impulse noise protection reporting mode." REFERENCE "ITU-T G.997.1 Amendment 1, paragraph #7.5.2.5 (INPREPORT)" DEFVAL { inpComputedUsingFormula } ::= { xdsl2ChannelStatusEntry 6 } xdsl2ChStatusNFec OBJECT-TYPE SYNTAX Gauge(0..255) -- Units -- bytes ACCESS read-only STATUS mandatory DESCRIPTION "Actual size of Reed-Solomon codeword. This parameter reports the actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. It ranges from 0 to 16. The value 0 indicates no Reed-Solomon coding." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.6.1 (NFEC)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 7 } xdsl2ChStatusRFec OBJECT-TYPE SYNTAX Gauge(0..16) -- Units -- bits ACCESS read-only STATUS mandatory DESCRIPTION "Actual number of Reed-Solomon redundancy bytes. This parameter reports the actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. It ranges from 0 to 16. The value 0 indicates no Reed-Solomon coding." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.6.2 (RFEC)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 8 } xdsl2ChStatusLSymb OBJECT-TYPE SYNTAX Gauge(0..65535) -- Units -- bits ACCESS read-only STATUS mandatory DESCRIPTION "Actual number of bits per symbol. This parameter reports the actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. The value is coded in bits. It ranges from 0 to 65535." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.6.3 (LSYMB)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 9 } xdsl2ChStatusIntlvDepth OBJECT-TYPE SYNTAX Gauge(1..4096) ACCESS read-only STATUS mandatory DESCRIPTION "Actual interleaving depth. This parameter reports the actual depth of the interleaver used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 in steps of 1. The value 1 indicates no interleaving." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.6.4 (INTLVDEPTH)" DEFVAL { 1 } ::= { xdsl2ChannelStatusEntry 10 } xdsl2ChStatusIntlvBlock OBJECT-TYPE SYNTAX Gauge(4..255) ACCESS read-only STATUS mandatory DESCRIPTION "Actual interleaving block length. This parameter reports the actual block length of the interleaver used in the latency path in which the bearer channel is transported. The value ranges from 4 to 255 in steps of 1." REFERENCE "ITU-T G.997.1, paragraph #7.5.2.6.5 (INTLVBLOCK)" DEFVAL { 4 } ::= { xdsl2ChannelStatusEntry 11 } xdsl2ChStatusLPath OBJECT-TYPE SYNTAX Gauge(0..3) ACCESS read-only STATUS mandatory DESCRIPTION "Actual latency path. This parameter reports the index of the actual latency path in which the bearer is transported. The valid values are 0, 1, 2 and 3. For G.992.1, the FAST path shall be mapped to the latency index 0, and the INTERLEAVED path shall be mapped to the latency index 1." REFERENCE "ITU-T G.997.1 amendment 1, paragraph #7.5.2.7 (LPATH)" DEFVAL { 0 } ::= { xdsl2ChannelStatusEntry 12 } xdsl2ChStatusAtmStatus OBJECT-TYPE SYNTAX Xdsl2ChAtmStatus -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- noDefect(0) -- noCellDelineation(1) -- lossOfCellDelineation(2) ACCESS read-only STATUS mandatory DESCRIPTION "Indicates current state (existing failures) of the DSL channel in case its Data Path is ATM. This is a bitmap of possible conditions. In case the channel is not of ATM Data Path, the object is set to '0'." REFERENCE "ITU-T G.997.1, paragraph #7.1.4 (ATM data path failures)" DEFVAL { '80'h } ::= { xdsl2ChannelStatusEntry 13 } xdsl2ChStatusPtmStatus OBJECT-TYPE SYNTAX Xdsl2ChPtmStatus -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- noDefect(0) -- outOfSync(1) ACCESS read-only STATUS mandatory DESCRIPTION "Indicates current state (existing failures) of the DSL channel in case its Data Path is PTM (Packet Transfer Mode). This is a bitmap of possible conditions. In case the channel is not of PTM Data Path, the object is set to '0'." REFERENCE "ITU-T G.997.1, paragraph #7.1.5 (PTM Data Path failures)" DEFVAL { '80'h } ::= { xdsl2ChannelStatusEntry 14 } xdsl2ScalarSCMaxInterfaces OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "This value determines the maximum number of interfaces supported by xdsl2SCStatusTable, xdsl2SCStatusBandTable, and xdsl2SCStatusSegmentTable." ::= { xdsl2ScalarSC 1 } xdsl2ScalarSCAvailInterfaces OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "This value determines the currently available number of interfaces listed in xdsl2SCStatusTable, xdsl2SCStatusBandTable, and xdsl2SCStatusSegmentTable." ::= { xdsl2ScalarSC 2 } xdsl2SCStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2SCStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2SCStatusTable contains status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that provide information about the size of parameters in xdsl2SCStatusSegmentTable. The parameters in this table MUST be updated after a loop diagnostic procedure, MAY be updated after a line initialization, and MAY be updated at Showtime." ::= { xdsl2Status 3 } xdsl2SCStatusEntry OBJECT-TYPE SYNTAX Xdsl2SCStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission direction." INDEX { ifIndex, xdsl2SCStatusDirection } ::= { xdsl2SCStatusTable 1 } Xdsl2SCStatusEntry ::= SEQUENCE { xdsl2SCStatusDirection Xdsl2Direction, xdsl2SCStatusLinScale Gauge, xdsl2SCStatusLinScGroupSize Gauge, xdsl2SCStatusLogMt Gauge, xdsl2SCStatusLogScGroupSize Gauge, xdsl2SCStatusQlnMt Gauge, xdsl2SCStatusQlnScGroupSize Gauge, xdsl2SCStatusSnrMtime Gauge, xdsl2SCStatusSnrScGroupSize Gauge, xdsl2SCStatusAttainableRate Gauge, xdsl2SCStatusRowStatus RowStatus } xdsl2SCStatusDirection OBJECT-TYPE SYNTAX Xdsl2Direction -- Rsyntax INTEGER { -- upstream(1), -- downstream(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The direction of the subcarrier either upstream or downstream." ::= { xdsl2SCStatusEntry 1 } xdsl2SCStatusLinScale OBJECT-TYPE SYNTAX Gauge(1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure. It is represented as an unsigned integer in the range from 1 to 2^16-1." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.26.1 (HLINSCds) and paragraph #7.5.1.26.7 (HLINSCus)" ::= { xdsl2SCStatusEntry 2 } xdsl2SCStatusLinScGroupSize OBJECT-TYPE SYNTAX Gauge(1..8) ACCESS read-only STATUS mandatory DESCRIPTION "Number of subcarriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a subcarrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.26.2 (HLINGds) and paragraph #7.5.1.26.8 (HLINGus)" ::= { xdsl2SCStatusEntry 3 } xdsl2SCStatusLogMt OBJECT-TYPE SYNTAX Gauge(1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This parameter contains the number of symbols used to measure the Hlog(f) values. It is represented as an unsigned integer in the range from 1 to 2^16-1. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to measure the Hlog(f). It should correspond to the value specified in the Recommendation (e.g., the number of symbols in 1 s time interval for ITU-T Recommendation. G.992.3)." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.26.4 (HLOGMTds) and paragraph #7.5.1.26.10 (HLOGMTus)" ::= { xdsl2SCStatusEntry 4 } xdsl2SCStatusLogScGroupSize OBJECT-TYPE SYNTAX Gauge(1..8) ACCESS read-only STATUS mandatory DESCRIPTION "Number of subcarriers per group used to report the H(f) logarithmic representation values for the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to 1, and for VDSL2, it is equal to the size of a subcarrier group used to compute these parameters." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.26.5 (HLOGGds) and paragraph #7.5.1.26.11 (HLOGGus)" ::= { xdsl2SCStatusEntry 5 } xdsl2SCStatusQlnMt OBJECT-TYPE SYNTAX Gauge(1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This parameter contains the number of symbols used to measure the QLN(f) values. It is an unsigned integer in the range from 1 to 2^16-1. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to measure the QLN(f). It should correspond to the value specified in the Recommendation (e.g., the number of symbols in 1 s time interval for ITU-T Recommendation G.992.3)." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.27.1 (QLNMTds) and paragraph #7.5.1.27.4 (QLNMTus)" ::= { xdsl2SCStatusEntry 6 } xdsl2SCStatusQlnScGroupSize OBJECT-TYPE SYNTAX Gauge(1..8) ACCESS read-only STATUS mandatory DESCRIPTION "Number of subcarriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to 1, and for VDSL2, it is equal to the size of a subcarrier group used to compute these parameters." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.27.2 (QLNGds) and paragraph #7.5.1.27.5 (QLNGus)" ::= { xdsl2SCStatusEntry 7 } xdsl2SCStatusSnrMtime OBJECT-TYPE SYNTAX Gauge(1..65535) -- Units -- symbols ACCESS read-only STATUS mandatory DESCRIPTION "This parameter contains the number of symbols used to measure the SNR(f) values. It is an unsigned integer in the range from 1 to 2^16-1. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to measure the SNR(f). It should correspond to the value specified in the Recommendation (e.g., the number of symbols in 1 s time interval for ITU-T Recommendation G.992.3)." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.28.1 (SNRMTds) and paragraph #7.5.1.28.4 (SNRMTus)" ::= { xdsl2SCStatusEntry 8 } xdsl2SCStatusSnrScGroupSize OBJECT-TYPE SYNTAX Gauge(1..8) ACCESS read-only STATUS mandatory DESCRIPTION "Number of subcarriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to 1, and for VDSL2, it is equal to the size of a subcarrier group used to compute these parameters." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.28.2 (SNRGds) and paragraph #7.5.1.28.5 (SNRGus)" ::= { xdsl2SCStatusEntry 9 } xdsl2SCStatusAttainableRate OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-only STATUS mandatory DESCRIPTION "Maximum Attainable Data Rate. The maximum net data rate currently attainable by the xTU-C transmitter and xTU-R receiver (when referring to downstream direction) or by the xTU-R transmitter and xTU-C receiver (when referring to upstream direction). Value is coded in bits/s. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.19 (ATTNDRds) and paragraph #7.5.1.20 (ATTNDRus)" ::= { xdsl2SCStatusEntry 10 } xdsl2SCStatusRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Row Status. The SNMP agent will create a row in this table for storing the results of a DELT performed on the associated line, if the row does not already exist. When a row is created in this table, the SNMP agent should also create corresponding rows in the tables xdsl2SCStatusBandTable and xdsl2SCStatusSegmentTable. The SNMP manager is not permitted to create rows in this table or set the row status to 'notInService'. In the first case, if the SNMP manager tries to create a new row, the SNMP agent responds with the value 'noCreation' in the error status field of the response-PDU. In the latter case the SNMP agent responds with the value 'wrongValue' in the error status field of the response-PDU. When a row is deleted in this table, the SNMP agent should also delete corresponding rows in the tables xdsl2SCStatusBandTable and xdsl2SCStatusSegmentTable. The SNMP agent may have limited resources; therefore, if multiple rows coexist in this table, it may fail to add new rows to this table or allocate memory resources for a new DELT process. If that occurs, the SNMP agent responds with either the value 'tableFull' or the value 'noResources' (for the xdsl2LineCmndConfLdsfFailReason object in xdsl2LineTable). The management system (the operator) may delete rows from this table according to any scheme. For example, after retrieving the results." ::= { xdsl2SCStatusEntry 11 } xdsl2SCStatusBandTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2SCStatusBandEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2SCStatusBandTable contains subcarrier status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that are grouped per- band. For ADSL/ADSL2/ADSL2+, there is a single upstream band and a single downstream band. For VDSL2, there are several downstream bands and several upstream bands. The parameters in this table are only available after a loop diagnostic procedure." ::= { xdsl2Status 4 } xdsl2SCStatusBandEntry OBJECT-TYPE SYNTAX Xdsl2SCStatusBandEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission band." INDEX { ifIndex, xdsl2SCStatusBand } ::= { xdsl2SCStatusBandTable 1 } Xdsl2SCStatusBandEntry ::= SEQUENCE { xdsl2SCStatusBand Xdsl2Band, xdsl2SCStatusBandLnAtten Gauge, xdsl2SCStatusBandSigAtten Gauge } xdsl2SCStatusBand OBJECT-TYPE SYNTAX Xdsl2Band -- Rsyntax INTEGER { -- upstream(1), -- downstream(2), -- us0(3), -- ds1(4), -- us1(5), -- ds2(6), -- us2(7), -- ds3(8), -- us3(9), -- ds4(10), -- us4(11) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The transmission band." ::= { xdsl2SCStatusBandEntry 1 } xdsl2SCStatusBandLnAtten OBJECT-TYPE SYNTAX Gauge(0..2147483647) -- Units -- 0.1 dB ACCESS read-only STATUS mandatory DESCRIPTION "When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers during diagnostics mode. When referring to a band in the upstream direction, it is the measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all subcarriers during diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.9 (LATNds) and paragraph #7.5.1.10 (LATNus)" DEFVAL { 2147483646 } ::= { xdsl2SCStatusBandEntry 2 } xdsl2SCStatusBandSigAtten OBJECT-TYPE SYNTAX Gauge(0..2147483647) -- Units -- 0.1 dB ACCESS read-only STATUS mandatory DESCRIPTION "When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers during Showtime after the diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all subcarriers during Showtime after the diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.11 (SATNds) and paragraph #7.5.1.12 (SATNus)" DEFVAL { 2147483646 } ::= { xdsl2SCStatusBandEntry 3 } xdsl2SCStatusSegmentTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2SCStatusSegmentEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2SCStatusSegmentTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers. Several objects in the table refer to NSus and NSds. For G.993.2, the value of NSus and NSds are, respectively, the indices of the highest supported upstream and downstream subcarriers according to the selected implementation profile. For ADSL, NSus is equal to NSCus-1 and NSds is equal to NSCds-1. The parameters in this table MUST be updated after a loop diagnostic procedure and MAY be updated after a line initialization and MAY be updated at Showtime." ::= { xdsl2Status 5 } xdsl2SCStatusSegmentEntry OBJECT-TYPE SYNTAX Xdsl2SCStatusSegmentEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission direction. A third index identifies the specific segment of the subcarriers status addressed." INDEX { ifIndex, xdsl2SCStatusDirection, xdsl2SCStatusSegment } ::= { xdsl2SCStatusSegmentTable 1 } Xdsl2SCStatusSegmentEntry ::= SEQUENCE { xdsl2SCStatusSegment Gauge, xdsl2SCStatusSegmentLinReal OCTET STRING, xdsl2SCStatusSegmentLinImg OCTET STRING, xdsl2SCStatusSegmentLog OCTET STRING, xdsl2SCStatusSegmentQln OCTET STRING, xdsl2SCStatusSegmentSnr OCTET STRING, xdsl2SCStatusSegmentBitsAlloc Xdsl2BitsAlloc, xdsl2SCStatusSegmentGainAlloc OCTET STRING } xdsl2SCStatusSegment OBJECT-TYPE SYNTAX Gauge(1..8) ACCESS not-accessible STATUS mandatory DESCRIPTION "The segment of the subcarriers status information provided by this row. Several status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with xdsl2SCStatusSegment=1, the second segment is retrieved with xdsl2SCStatusSegment=2, and so on. When any status parameter is retrieved in n segments where n<8), then for that parameter, GET operations for the remaining segment numbers (n+1 to 8) will respond with a zero-length OCTET STRING." ::= { xdsl2SCStatusSegmentEntry 1 } xdsl2SCStatusSegmentLinReal OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..1024)) ACCESS read-only STATUS mandatory DESCRIPTION "An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) subcarrier groups and can be retrieved in a single segment. The number of utilized values in the downstream direction depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. Each array entry represents the real component (referred to here as a(i)) of Hlin(f = i*Df) value for a particular subcarrier group index i (0 <= i <= NS). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is xdsl2SCStatusLinScale and a(i) and b(i) (provided by the xdsl2SCStatusSegmentLinImg object) are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.26.3 (HLINpsds) and paragraph #7.5.1.26.9 (HLINpsus)" ::= { xdsl2SCStatusSegmentEntry 2 } xdsl2SCStatusSegmentLinImg OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..1024)) ACCESS read-only STATUS mandatory DESCRIPTION "An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) subcarrier groups and can be retrieved in a single segment. The number of utilized values in the downstream direction depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. Each array entry represents the imaginary component (referred to here as b(i)) of Hlin(f = i*Df) value for a particular subcarrier group index i (0 <= i <= NS). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is xdsl2SCStatusLinScale and a(i) (provided by the xdsl2SCStatusSegmentLinReal object) and b(i) are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.26.3 (HLINpsds) and paragraph #7.5.1.26.9 (HLINpsus)" ::= { xdsl2SCStatusSegmentEntry 3 } xdsl2SCStatusSegmentLog OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..1024)) -- Units -- dB ACCESS read-only STATUS mandatory DESCRIPTION "An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) subcarrier groups and can be retrieved in a single segment. The number of utilized values in the downstream direction depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. Each array entry represents the real Hlog(f = i*Df) value for a particular subcarrier group index i, (0 <= i <= NS). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.26.6 (HLOGpsds) and paragraph #7.5.1.26.12 (HLOGpsus)" ::= { xdsl2SCStatusSegmentEntry 4 } xdsl2SCStatusSegmentQln OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..512)) -- Units -- dBm/Hz ACCESS read-only STATUS mandatory DESCRIPTION "An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) subcarrier groups and can be retrieved in a single segment. The number of utilized values in the downstream direction depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. Each array entry represents the QLN(f = i*Df) value for a particular subcarrier index i, (0 <= i <= NS). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier group because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.27.3 (QLNpsds) and paragraph #7.5.1.27.6 (QLNpsus)" ::= { xdsl2SCStatusSegmentEntry 5 } xdsl2SCStatusSegmentSnr OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..512)) -- Units -- 0.5 dB ACCESS read-only STATUS mandatory DESCRIPTION "The SNR Margin per subcarrier group, expressing the ratio between the received signal power and received noise power per subscriber group. It is an array of 512 octets, designed for supporting up to 512 (downstream) subcarrier groups and can be retrieved in a single segment. The number of utilized octets in the downstream direction depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. Octet i (0 <= i <= NS) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream subcarrier group i has an SNR of: (-32 + xdsl2SCStatusSegmentSnr(i)/2) in dB (i.e., -32 to 95 dB). The special value 255 means that no measurement could be done for the subcarrier group because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.28.3 (SNRpsds) and paragraph #7.5.1.28.6 (SNRpsus)" ::= { xdsl2SCStatusSegmentEntry 6 } xdsl2SCStatusSegmentBitsAlloc OBJECT-TYPE SYNTAX Xdsl2BitsAlloc -- Rsyntax OCTET STRING(SIZE(0..256)) -- Units -- bits ACCESS read-only STATUS mandatory DESCRIPTION "The bits allocation per subcarrier. An array of 256 octets (512 nibbles) designed for supporting up to 512 (downstream) subcarriers. When more than 512 subcarriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 subcarriers. The second segment is used for the subcarriers 512 to 1023 and so on. The aggregate number of utilized nibbles in the downstream direction (in all segments) depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. The segment number is in xdsl2SCStatusSegment. Nibble i (0 <= i < MIN((NS+1)-(segment-1)*512,512)) in each segment is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream subcarrier j (j=(segement-1)*512+i) has the same amount of bits allocation." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.29.1 (BITSpsds) and paragraph #7.5.1.29.2 (BITSpsus)" ::= { xdsl2SCStatusSegmentEntry 7 } xdsl2SCStatusSegmentGainAlloc OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..1024)) ACCESS read-only STATUS mandatory DESCRIPTION "The gain allocation per subcarrier. An array of 512 16-bit values, designed for supporting up to 512 (downstream) subcarriers. When more then 512 subcarriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 subcarriers. The second segment is used for the subcarriers 512 to 1023 and so on. The aggregate number of utilized octets in the downstream direction depends on NSds; in the upstream direction, it depends on NSus. This value is referred to here as NS. The segment number is in xdsl2SCStatusSegment. Value i (0 <= i < MIN((NS+1)-(segment-1)*512,512)) in each segment is set to a value in the range 0 to 4093 to indicate that the respective downstream or upstream subcarrier j (j=(segement-1)*512+i) has the same amount of gain value. The gain value is represented as a multiple of 1/512 on a linear scale. Each value in this array is 16 bits wide and is stored in big endian format." REFERENCE "ITU-T G.997.1, paragraph #7.5.1.29.3 (GAINSpsds) and paragraph #7.5.1.29.4 (GAINSpsus)" ::= { xdsl2SCStatusSegmentEntry 8 } xdsl2LineInventoryTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineInventoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineInventoryTable contains an inventory of the DSL termination unit." ::= { xdsl2Inventory 1 } xdsl2LineInventoryEntry OBJECT-TYPE SYNTAX Xdsl2LineInventoryEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the termination unit." INDEX { ifIndex, xdsl2LInvUnit } ::= { xdsl2LineInventoryTable 1 } Xdsl2LineInventoryEntry ::= SEQUENCE { xdsl2LInvUnit Xdsl2Unit, xdsl2LInvG994VendorId OCTET STRING, xdsl2LInvSystemVendorId OCTET STRING, xdsl2LInvVersionNumber OCTET STRING, xdsl2LInvSerialNumber OCTET STRING, xdsl2LInvSelfTestResult Gauge, xdsl2LInvTransmissionCapabilities Xdsl2TransmissionModeType } xdsl2LInvUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2LineInventoryEntry 1 } xdsl2LInvG994VendorId OBJECT-TYPE SYNTAX OCTET STRING(SIZE(8)) ACCESS read-only STATUS mandatory DESCRIPTION "The ADSL Transceiver Unit (ATU) G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35." REFERENCE "ITU-T G.997.1, paragraph #7.4.1-7.4.2" ::= { xdsl2LineInventoryEntry 2 } xdsl2LInvSystemVendorId OBJECT-TYPE SYNTAX OCTET STRING(SIZE(8)) ACCESS read-only STATUS mandatory DESCRIPTION "The ATU System Vendor ID (identifies the xTU system integrator) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embedded Operations Channel (xTU-R in G.992.1 and G.992.2). It consists of 8 binary octets, with same format as used for Xdsl2InvG994VendorId." REFERENCE "ITU-T G.997.1, paragraph #7.4.3-7.4.4" ::= { xdsl2LineInventoryEntry 3 } xdsl2LInvVersionNumber OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "The xTU version number (vendor-specific information) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embedded Operations Channel (xTU-R in G.992.1 and G.992.2). It consists of up to 16 binary octets." REFERENCE "ITU-T G.997.1, paragraph #7.4.5-7.4.6" ::= { xdsl2LineInventoryEntry 4 } xdsl2LInvSerialNumber OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "The xTU serial number (vendor-specific information) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embedded Operations Channel (xTU-R in G.992.1 and G.992.2). It is vendor-specific information consisting of up to 32 ASCII characters." REFERENCE "ITU-T G.997.1, paragraph #7.4.7-7.4.8" ::= { xdsl2LineInventoryEntry 5 } xdsl2LInvSelfTestResult OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The xTU self-test result, coded as a 32-bit value. The most significant octet of the result is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretionary." REFERENCE "ITU-T G.997.1, paragraph #7.4.9-7.4.10" DEFVAL { 0 } ::= { xdsl2LineInventoryEntry 6 } xdsl2LInvTransmissionCapabilities OBJECT-TYPE SYNTAX Xdsl2TransmissionModeType -- Rsyntax OCTET STRING(SIZE(1..8)) -- BITS are: -- ansit1413(0) -- etsi(1) -- g9921PotsNonOverlapped(2) -- g9921PotsOverlapped(3) -- g9921IsdnNonOverlapped(4) -- g9921isdnOverlapped(5) -- g9921tcmIsdnNonOverlapped(6) -- g9921tcmIsdnOverlapped(7) -- g9922potsNonOverlapped(8) -- g9922potsOverlapped(9) -- g9922tcmIsdnNonOverlapped(10) -- g9922tcmIsdnOverlapped(11) -- g9921tcmIsdnSymmetric(12) -- reserved1(13) -- reserved2(14) -- reserved3(15) -- reserved4(16) -- reserved5(17) -- g9923PotsNonOverlapped(18) -- g9923PotsOverlapped(19) -- g9923IsdnNonOverlapped(20) -- g9923isdnOverlapped(21) -- reserved6(22) -- reserved7(23) -- g9924potsNonOverlapped(24) -- g9924potsOverlapped(25) -- reserved8(26) -- reserved9(27) -- g9923AnnexIAllDigNonOverlapped(28) -- g9923AnnexIAllDigOverlapped(29) -- g9923AnnexJAllDigNonOverlapped(30) -- g9923AnnexJAllDigOverlapped(31) -- g9924AnnexIAllDigNonOverlapped(32) -- g9924AnnexIAllDigOverlapped(33) -- g9923AnnexLMode1NonOverlapped(34) -- g9923AnnexLMode2NonOverlapped(35) -- g9923AnnexLMode3Overlapped(36) -- g9923AnnexLMode4Overlapped(37) -- g9923AnnexMPotsNonOverlapped(38) -- g9923AnnexMPotsOverlapped(39) -- g9925PotsNonOverlapped(40) -- g9925PotsOverlapped(41) -- g9925IsdnNonOverlapped(42) -- g9925isdnOverlapped(43) -- reserved10(44) -- reserved11(45) -- g9925AnnexIAllDigNonOverlapped(46) -- g9925AnnexIAllDigOverlapped(47) -- g9925AnnexJAllDigNonOverlapped(48) -- g9925AnnexJAllDigOverlapped(49) -- g9925AnnexMPotsNonOverlapped(50) -- g9925AnnexMPotsOverlapped(51) -- reserved12(52) -- reserved13(53) -- reserved14(54) -- reserved15(55) -- g9932AnnexA(56) -- g9932AnnexB(57) -- g9932AnnexC(58) -- reserved16(59) -- reserved17(60) -- reserved18(61) -- reserved19(62) -- reserved20(63) ACCESS read-only STATUS mandatory DESCRIPTION "The xTU transmission system capability list of the different coding types. It is coded in a bitmap representation with 1 or more bits set. A bit set to '1' means that the xTU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1. A set of xDSL line transmission modes, with one bit per mode." REFERENCE "ITU-T G.997.1, paragraph #7.4.11-7.4.12" ::= { xdsl2LineInventoryEntry 7 } xdsl2LineConfTemplateTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineConfTemplateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineConfTemplateTable contains VDSL2/ADSL/ ADSL2 and ADSL2+ line configuration templates. Note that this table is also used to configure the number of bearer channels. When the number of bearer channels is increased, the SNMP agent SHOULD create rows in all tables indexed by a channel index. When the number of bearer channels is decreased, the SNMP agent SHOULD delete rows in all tables indexed by a channel index. For example, if the value of xdsl2LConfTempChan4ConfProfile is set to a non-null value, then rows SHOULD be created in xdsl2ChannelStatusTable, xdsl2PMChCurrTable, and all other tables indexed by a channel index. For example, if the value of xdsl2LConfTempChan2ConfProfile is set to a null value, then rows SHOULD be deleted in xdsl2ChannelStatusTable, xdsl2PMChCurrTable, and all other tables indexed by a channel index. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileLine 1 } xdsl2LineConfTemplateEntry OBJECT-TYPE SYNTAX Xdsl2LineConfTemplateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A default template with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this document." INDEX { xdsl2LConfTempTemplateName } ::= { xdsl2LineConfTemplateTable 1 } Xdsl2LineConfTemplateEntry ::= SEQUENCE { xdsl2LConfTempTemplateName SnmpAdminString, xdsl2LConfTempLineProfile SnmpAdminString, xdsl2LConfTempChan1ConfProfile SnmpAdminString, xdsl2LConfTempChan1RaRatioDs Gauge, xdsl2LConfTempChan1RaRatioUs Gauge, xdsl2LConfTempChan2ConfProfile SnmpAdminString, xdsl2LConfTempChan2RaRatioDs Gauge, xdsl2LConfTempChan2RaRatioUs Gauge, xdsl2LConfTempChan3ConfProfile SnmpAdminString, xdsl2LConfTempChan3RaRatioDs Gauge, xdsl2LConfTempChan3RaRatioUs Gauge, xdsl2LConfTempChan4ConfProfile SnmpAdminString, xdsl2LConfTempChan4RaRatioDs Gauge, xdsl2LConfTempChan4RaRatioUs Gauge, xdsl2LConfTempRowStatus RowStatus } xdsl2LConfTempTemplateName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This object identifies a row in this table." REFERENCE "DSL Forum TR-129, paragraph #5.4" ::= { xdsl2LineConfTemplateEntry 1 } xdsl2LConfTempLineProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the VDSL2/ADSL/ADSL2 and ADSL2+ line configuration Profile Table (xdsl2LineConfProfTable) that applies for this DSL line." REFERENCE "DSL Forum TR-129, paragraph #5.4" DEFVAL { "DEFVAL" } ::= { xdsl2LineConfTemplateEntry 2 } xdsl2LConfTempChan1ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #1. The channel profile name specified here MUST match the name of an existing row in the xdsl2ChConfProfileTable table." DEFVAL { "DEFVAL" } ::= { xdsl2LineConfTemplateEntry 3 } xdsl2LConfTempChan1RaRatioDs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan1RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 100 } ::= { xdsl2LineConfTemplateEntry 4 } xdsl2LConfTempChan1RaRatioUs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan1RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 100 } ::= { xdsl2LineConfTemplateEntry 5 } xdsl2LConfTempChan2ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #2. If the channel is unused, then the object is set to a zero-length string. This object may be set to a zero-length string only if xdsl2LConfTempChan3ConfProfile contains a zero-length string." DEFVAL { "" } ::= { xdsl2LineConfTemplateEntry 6 } xdsl2LConfTempChan2RaRatioDs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan2RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 0 } ::= { xdsl2LineConfTemplateEntry 7 } xdsl2LConfTempChan2RaRatioUs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan2RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 0 } ::= { xdsl2LineConfTemplateEntry 8 } xdsl2LConfTempChan3ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #3. If the channel is unused, then the object is set to a zero-length string. This object may be set to a zero-length string only if xdsl2LConfTempChan4ConfProfile contains a zero-length string. This object may be set to a non-zero-length string only if xdsl2LConfTempChan2ConfProfile contains a non-zero-length string." DEFVAL { "" } ::= { xdsl2LineConfTemplateEntry 9 } xdsl2LConfTempChan3RaRatioDs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan3RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 0 } ::= { xdsl2LineConfTemplateEntry 10 } xdsl2LConfTempChan3RaRatioUs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan3RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 0 } ::= { xdsl2LineConfTemplateEntry 11 } xdsl2LConfTempChan4ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #4. If the channel is unused, then the object is set to a zero-length string. This object may be set to a non-zero-length string only if xdsl2LConfTempChan3ConfProfile contains a non-zero-length string." DEFVAL { "" } ::= { xdsl2LineConfTemplateEntry 12 } xdsl2LConfTempChan4RaRatioDs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan4RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 0 } ::= { xdsl2LineConfTemplateEntry 13 } xdsl2LConfTempChan4RaRatioUs OBJECT-TYPE SYNTAX Gauge(0..100) -- Units -- percent ACCESS read-write STATUS mandatory DESCRIPTION "Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - xdsl2LConfTempChan4RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.4 (Rate adaptation ratio)" DEFVAL { 0 } ::= { xdsl2LineConfTemplateEntry 14 } xdsl2LConfTempRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated lines. A row in this table is said to be unreferenced when there is no instance of xdsl2LineConfTemplate or xdsl2LineConfFallbackTemplate that refers to the row." ::= { xdsl2LineConfTemplateEntry 15 } xdsl2LineConfProfTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineConfProfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineConfProfTable contains VDSL2/ADSL/ ADSL2 and ADSL2+ line configuration profiles. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileLine 2 } xdsl2LineConfProfEntry OBJECT-TYPE SYNTAX Xdsl2LineConfProfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this document." INDEX { xdsl2LConfProfProfileName } ::= { xdsl2LineConfProfTable 1 } Xdsl2LineConfProfEntry ::= SEQUENCE { xdsl2LConfProfProfileName SnmpAdminString, xdsl2LConfProfScMaskDs Xdsl2ScMaskDs, xdsl2LConfProfScMaskUs Xdsl2ScMaskUs, xdsl2LConfProfVdsl2CarMask Xdsl2CarMask, xdsl2LConfProfRfiBands Xdsl2RfiBands, xdsl2LConfProfRaModeDs Xdsl2RaMode, xdsl2LConfProfRaModeUs Xdsl2RaMode, xdsl2LConfProfRaUsNrmDs Gauge, xdsl2LConfProfRaUsNrmUs Gauge, xdsl2LConfProfRaUsTimeDs Gauge, xdsl2LConfProfRaUsTimeUs Gauge, xdsl2LConfProfRaDsNrmDs Gauge, xdsl2LConfProfRaDsNrmUs Gauge, xdsl2LConfProfRaDsTimeDs Gauge, xdsl2LConfProfRaDsTimeUs Gauge, xdsl2LConfProfTargetSnrmDs Gauge, xdsl2LConfProfTargetSnrmUs Gauge, xdsl2LConfProfMaxSnrmDs Gauge, xdsl2LConfProfMaxSnrmUs Gauge, xdsl2LConfProfMinSnrmDs Gauge, xdsl2LConfProfMinSnrmUs Gauge, xdsl2LConfProfMsgMinUs Gauge, xdsl2LConfProfMsgMinDs Gauge, xdsl2LConfProfCeFlag Xdsl2LineCeFlag, xdsl2LConfProfSnrModeDs Xdsl2LineSnrMode, xdsl2LConfProfSnrModeUs Xdsl2LineSnrMode, xdsl2LConfProfTxRefVnDs Xdsl2LineTxRefVnDs, xdsl2LConfProfTxRefVnUs Xdsl2LineTxRefVnUs, xdsl2LConfProfXtuTransSysEna Xdsl2TransmissionModeType, xdsl2LConfProfPmMode Xdsl2LinePmMode, xdsl2LConfProfL0Time Gauge, xdsl2LConfProfL2Time Gauge, xdsl2LConfProfL2Atpr Gauge, xdsl2LConfProfL2Atprt Gauge, xdsl2LConfProfProfiles Xdsl2LineProfiles, xdsl2LConfProfDpboEPsd Xdsl2PsdMaskDs, xdsl2LConfProfDpboEsEL Gauge, xdsl2LConfProfDpboEsCableModelA Gauge, xdsl2LConfProfDpboEsCableModelB Gauge, xdsl2LConfProfDpboEsCableModelC Gauge, xdsl2LConfProfDpboMus Gauge, xdsl2LConfProfDpboFMin Gauge, xdsl2LConfProfDpboFMax Gauge, xdsl2LConfProfUpboKL Gauge, xdsl2LConfProfUpboKLF Xdsl2UpboKLF, xdsl2LConfProfUs0Mask Xdsl2LineUs0Mask, xdsl2LConfProfForceInp TruthValue, xdsl2LConfProfRowStatus RowStatus } xdsl2LConfProfProfileName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This object identifies a row in this table." ::= { xdsl2LineConfProfEntry 1 } xdsl2LConfProfScMaskDs OBJECT-TYPE SYNTAX Xdsl2ScMaskDs -- Rsyntax OCTET STRING(SIZE(0..512)) ACCESS read-write STATUS mandatory DESCRIPTION "Subcarrier mask. A bitmap of 4096 bits that allows masking up to 4096 downstream subcarriers. If bit i (0 <= i < NSCds) is set to '1', the respective downstream subcarrier is masked, and if set to '0', the respective subcarrier is unmasked. Note that there should always be unmasked subcarriers (i.e., this object cannot be all 1's). Also note that if NSCds < 4096, all bits i (NSCds < i <= 4096) should be set to '1'." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.6 (CARMASKds)" ::= { xdsl2LineConfProfEntry 2 } xdsl2LConfProfScMaskUs OBJECT-TYPE SYNTAX Xdsl2ScMaskUs -- Rsyntax OCTET STRING(SIZE(0..512)) ACCESS read-write STATUS mandatory DESCRIPTION "Subcarrier mask. A bitmap of 4096 bits that allows masking up to 4096 upstream subcarriers. If bit i (0 <= i < NSCus) is set to '1', the respective upstream subcarrier is masked, and if set to '0', the respective subcarrier is unmasked. Note that there should always be unmasked subcarriers (i.e., this object cannot be all 1's). Also note that if NSCus < 4096, all bits i (NSCus < i <= 4096) should be set to '1'." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.7 (CARMASKus)" ::= { xdsl2LineConfProfEntry 3 } xdsl2LConfProfVdsl2CarMask OBJECT-TYPE SYNTAX Xdsl2CarMask -- Rsyntax OCTET STRING(SIZE(0..128)) ACCESS read-write STATUS mandatory DESCRIPTION "VDSL2-specific subcarrier mask. This configuration parameter defines the restrictions, additional to the band plan, to determine the set of subcarriers allowed for transmission in both the upstream and downstream directions. The parameter shall describe the not masked subcarriers as one or more frequency bands. Each band is represented by start and stop subcarrier indices with a subcarrier spacing of 4.3125 kHz. The valid range of subcarrier indices runs from 0 to at least the index of the highest allowed subcarrier in both transmission directions among all profiles enabled by the parameter xdsl2LConfProfProfiles. Up to 32 bands may be specified. Other subcarriers shall be masked." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.8 (VDSL2- CARMASK)" ::= { xdsl2LineConfProfEntry 4 } xdsl2LConfProfRfiBands OBJECT-TYPE SYNTAX Xdsl2RfiBands -- Rsyntax OCTET STRING(SIZE(0..64)) ACCESS read-write STATUS mandatory DESCRIPTION "For ITU-T Recommendation G.992.5, this configuration parameter defines the subset of downstream PSD mask breakpoints, as specified in xdsl2LConfProfPsdMaskDs (PSDMASKds), that shall be used to notch an RFI band. This subset consists of pairs of consecutive subcarrier indices belonging to breakpoints: [ti; ti + 1], corresponding to the low level of the notch. The specific interpolation around these points is defined in the relevant Recommendations (e.g., ITU-T Recommendation G.992.5). The CO-MIB shall define the RFI notches using breakpoints in xdsl2LConfProfPsdMaskDs (PSDMASKds) as specified in the relevant Recommendations (e.g., ITU-T Recommendation G.992.5). For ITU-T Recommendation G.993.2, this configuration parameter defines the bands where the PSD shall be reduced as specified in #7.2.1.2/G.993.2. Each band shall be represented by a start and stop subcarrier indices with a subcarrier spacing of 4.3125 kHz. Up to 16 bands may be specified. This parameter defines the RFI bands for both the upstream and downstream directions." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.10 (RFIBANDS)" ::= { xdsl2LineConfProfEntry 5 } xdsl2LConfProfRaModeDs OBJECT-TYPE SYNTAX Xdsl2RaMode -- Rsyntax INTEGER { -- manual(1), -- raInit(2), -- dynamicRa(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "The mode of operation of a rate-adaptive xTU-C in the transmit direction." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.1 (RA-MODEds)" DEFVAL { manual } ::= { xdsl2LineConfProfEntry 6 } xdsl2LConfProfRaModeUs OBJECT-TYPE SYNTAX Xdsl2RaMode -- Rsyntax INTEGER { -- manual(1), -- raInit(2), -- dynamicRa(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "The mode of operation of a rate-adaptive xTU-R in the transmit direction." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.2 (RA-MODEus)" DEFVAL { manual } ::= { xdsl2LineConfProfEntry 7 } xdsl2LConfProfRaUsNrmDs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The Downstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. If the downstream noise margin is above this value, and stays above it, for more than the time specified by the xdsl2LConfProfRaUsTimeDs, the xTU-R shall attempt to increase the downstream net data rate. The Downstream Up-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.3 (RA-USNRMds)" DEFVAL { 10 } ::= { xdsl2LineConfProfEntry 8 } xdsl2LConfProfRaUsNrmUs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The Upstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. If the upstream noise margin is above this value, and stays above it, for more than the time specified by the xdsl2LConfProfRaUsTimeUs, the xTU-C shall attempt to increase the upstream net data rate. The Upstream Up-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.4 (RA-USNRMus)" DEFVAL { 10 } ::= { xdsl2LineConfProfEntry 9 } xdsl2LConfProfRaUsTimeDs OBJECT-TYPE SYNTAX Gauge(0..16383) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "The Downstream Up-Shift Time Interval, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. The interval of time that the downstream noise margin should stay above the Downstream Up-Shift Noise Margin before the xTU-R shall attempt to increase the downstream net data rate. The time interval ranges from 0 to 16383 seconds." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.5 (RA-UTIMEds)" DEFVAL { 3600 } ::= { xdsl2LineConfProfEntry 10 } xdsl2LConfProfRaUsTimeUs OBJECT-TYPE SYNTAX Gauge(0..16383) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "The Upstream Up-Shift Time Interval, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. The interval of time the upstream noise margin should stay above the Upstream Up-Shift Noise Margin before the xTU-C shall attempt to increase the upstream net data rate. The time interval ranges from 0 to 16383 seconds." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.6 (RA-UTIMEus)" DEFVAL { 3600 } ::= { xdsl2LineConfProfEntry 11 } xdsl2LConfProfRaDsNrmDs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The Downstream Down-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. If the downstream noise margin is below this value and stays below that value, for more than the time specified by the xdsl2LConfProfRaDsTimeDs, the xTU-R shall attempt to decrease the downstream net data rate. The Downstream Down-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.7 (RA-DSNRMds)" DEFVAL { 10 } ::= { xdsl2LineConfProfEntry 12 } xdsl2LConfProfRaDsNrmUs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The Upstream Downshift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. If the upstream noise margin is below this value and stays below that value, for more than the time specified by the xdsl2LConfProfRaDsTimeUs, the xTU-C shall attempt to decrease the upstream net data rate. The Upstream Down-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.8 (RA-DSNRMus)" DEFVAL { 10 } ::= { xdsl2LineConfProfEntry 13 } xdsl2LConfProfRaDsTimeDs OBJECT-TYPE SYNTAX Gauge(0..16383) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "The Downstream Downshift Time Interval, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. The interval of time the downstream noise margin should stay below the Downstream Down-Shift Noise Margin before the xTU-R shall attempt to decrease the downstream net data rate. The time interval ranges from 0 to 16383 seconds." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.9 (RA-DTIMEds)" DEFVAL { 3600 } ::= { xdsl2LineConfProfEntry 14 } xdsl2LConfProfRaDsTimeUs OBJECT-TYPE SYNTAX Gauge(0..16383) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "The Upstream Down-Shift Time Interval, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. The interval of time the upstream noise margin should stay below the Upstream Down-Shift Noise Margin before the xTU-C shall attempt to decrease the upstream net data rate. The time interval ranges from 0 to 16383 seconds." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.4.10 (RA-DTIMEus)" DEFVAL { 3600 } ::= { xdsl2LineConfProfEntry 15 } xdsl2LConfProfTargetSnrmDs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.3.1 (TARSNRMds)" DEFVAL { 60 } ::= { xdsl2LineConfProfEntry 16 } xdsl2LConfProfTargetSnrmUs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.3.2 (TARSNRMus)" DEFVAL { 60 } ::= { xdsl2LineConfProfEntry 17 } xdsl2LConfProfMaxSnrmDs OBJECT-TYPE SYNTAX Gauge(0..2147483647) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The maximum Noise Margin the xTU-R receiver shall try to sustain. If the Noise Margin is above this level, the xTU-R shall request that the xTU-C reduce the xTU-C transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0x7FFFFFFF (2147483647) means that there is no maximum." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.3.3 (MAXSNRMds)" DEFVAL { 310 } ::= { xdsl2LineConfProfEntry 18 } xdsl2LConfProfMaxSnrmUs OBJECT-TYPE SYNTAX Gauge(0..2147483647) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The maximum Noise Margin the xTU-C receiver shall try to sustain. If the Noise Margin is above this level, the xTU-C shall request that the xTU-R reduce the xTU-R transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0x7FFFFFFF (2147483647) means that there is no maximum." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.3.4 (MAXSNRMus)" DEFVAL { 310 } ::= { xdsl2LineConfProfEntry 19 } xdsl2LConfProfMinSnrmDs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The minimum Noise Margin the xTU-R receiver shall tolerate. If the noise margin falls below this level, the xTU-R shall request that the xTU-C increase the xTU-C transmit power. If an increase to xTU-C transmit power is not possible, a loss- of-margin (LOM) defect occurs, the xTU-R shall fail and attempt to reinitialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0 means that there is no minimum." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.3.5 (MINSNRMds)" DEFVAL { 10 } ::= { xdsl2LineConfProfEntry 20 } xdsl2LConfProfMinSnrmUs OBJECT-TYPE SYNTAX Gauge(0..310) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "The minimum Noise Margin the xTU-C receiver shall tolerate. If the noise margin falls below this level, the xTU-C shall request that the xTU-R increase the xTU-R transmit power. If an increase of xTU-R transmit power is not possible, a loss- of-margin (LOM) defect occurs, the xTU-C shall fail and attempt to re-initialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0 means that there is no minimum." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.3.6 (MINSNRMus)" DEFVAL { 10 } ::= { xdsl2LineConfProfEntry 21 } xdsl2LConfProfMsgMinUs OBJECT-TYPE SYNTAX Gauge(4000..248000) -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in upstream direction. Expressed in bits per second and ranges from 4000 to 248000 bits/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.5.1 (MSGMINus)" DEFVAL { 4000 } ::= { xdsl2LineConfProfEntry 22 } xdsl2LConfProfMsgMinDs OBJECT-TYPE SYNTAX Gauge(4000..248000) -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in the downstream direction. Expressed in bits per second and ranges from 4000 to 248000 bits/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.5.2 (MSGMINds)" DEFVAL { 4000 } ::= { xdsl2LineConfProfEntry 23 } xdsl2LConfProfCeFlag OBJECT-TYPE SYNTAX Xdsl2LineCeFlag -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- enableCyclicExtension(0) ACCESS read-write STATUS mandatory DESCRIPTION "This parameter is a bit that enables the use of the optional cyclic extension values." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.6.1 (CEFLAG)" DEFVAL { '00'h } ::= { xdsl2LineConfProfEntry 24 } xdsl2LConfProfSnrModeDs OBJECT-TYPE SYNTAX Xdsl2LineSnrMode -- Rsyntax INTEGER { -- virtualNoiseDisabled(1), -- virtualNoiseEnabled(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter enables the transmitter-referred virtual noise in the downstream direction." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.7.1 (SNRMODEds)" DEFVAL { virtualNoiseDisabled } ::= { xdsl2LineConfProfEntry 25 } xdsl2LConfProfSnrModeUs OBJECT-TYPE SYNTAX Xdsl2LineSnrMode -- Rsyntax INTEGER { -- virtualNoiseDisabled(1), -- virtualNoiseEnabled(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter enables the transmitter-referred virtual noise in the upstream direction." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.7.2 (SNRMODEus)" DEFVAL { virtualNoiseDisabled } ::= { xdsl2LineConfProfEntry 26 } xdsl2LConfProfTxRefVnDs OBJECT-TYPE SYNTAX Xdsl2LineTxRefVnDs -- Rsyntax OCTET STRING(SIZE(0..96)) ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the downstream transmitter-referred virtual noise. The TXREFVNds shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index t, with a subcarrier spacing of 4.3125 kHz, and a noise PSD level (expressed in dBm/Hz) at that subcarrier. The set of breakpoints can then be represented as: [(t1,PSD1), (t2, PSD2), ... , (tN, PSDN)]." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.7.3 (TXREFVNds)" ::= { xdsl2LineConfProfEntry 27 } xdsl2LConfProfTxRefVnUs OBJECT-TYPE SYNTAX Xdsl2LineTxRefVnUs -- Rsyntax OCTET STRING(SIZE(0..48)) ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the upstream transmitter-referred virtual noise. The TXREFVNus shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index t, with a subcarrier spacing of 4.3125 kHz, and a noise PSD level (expressed in dBm/Hz) at that subcarrier. The set of breakpoints can then be represented as: [(t1, PSD1), (t2, PSD2), ... , (tN, PSDN)]." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.7.4 (TXREFVNus)" ::= { xdsl2LineConfProfEntry 28 } xdsl2LConfProfXtuTransSysEna OBJECT-TYPE SYNTAX Xdsl2TransmissionModeType -- Rsyntax OCTET STRING(SIZE(1..8)) -- BITS are: -- ansit1413(0) -- etsi(1) -- g9921PotsNonOverlapped(2) -- g9921PotsOverlapped(3) -- g9921IsdnNonOverlapped(4) -- g9921isdnOverlapped(5) -- g9921tcmIsdnNonOverlapped(6) -- g9921tcmIsdnOverlapped(7) -- g9922potsNonOverlapped(8) -- g9922potsOverlapped(9) -- g9922tcmIsdnNonOverlapped(10) -- g9922tcmIsdnOverlapped(11) -- g9921tcmIsdnSymmetric(12) -- reserved1(13) -- reserved2(14) -- reserved3(15) -- reserved4(16) -- reserved5(17) -- g9923PotsNonOverlapped(18) -- g9923PotsOverlapped(19) -- g9923IsdnNonOverlapped(20) -- g9923isdnOverlapped(21) -- reserved6(22) -- reserved7(23) -- g9924potsNonOverlapped(24) -- g9924potsOverlapped(25) -- reserved8(26) -- reserved9(27) -- g9923AnnexIAllDigNonOverlapped(28) -- g9923AnnexIAllDigOverlapped(29) -- g9923AnnexJAllDigNonOverlapped(30) -- g9923AnnexJAllDigOverlapped(31) -- g9924AnnexIAllDigNonOverlapped(32) -- g9924AnnexIAllDigOverlapped(33) -- g9923AnnexLMode1NonOverlapped(34) -- g9923AnnexLMode2NonOverlapped(35) -- g9923AnnexLMode3Overlapped(36) -- g9923AnnexLMode4Overlapped(37) -- g9923AnnexMPotsNonOverlapped(38) -- g9923AnnexMPotsOverlapped(39) -- g9925PotsNonOverlapped(40) -- g9925PotsOverlapped(41) -- g9925IsdnNonOverlapped(42) -- g9925isdnOverlapped(43) -- reserved10(44) -- reserved11(45) -- g9925AnnexIAllDigNonOverlapped(46) -- g9925AnnexIAllDigOverlapped(47) -- g9925AnnexJAllDigNonOverlapped(48) -- g9925AnnexJAllDigOverlapped(49) -- g9925AnnexMPotsNonOverlapped(50) -- g9925AnnexMPotsOverlapped(51) -- reserved12(52) -- reserved13(53) -- reserved14(54) -- reserved15(55) -- g9932AnnexA(56) -- g9932AnnexB(57) -- g9932AnnexC(58) -- reserved16(59) -- reserved17(60) -- reserved18(61) -- reserved19(62) -- reserved20(63) ACCESS read-write STATUS mandatory DESCRIPTION "xTU Transmission System Enabling (XTSE). A list of the different coding types enabled in this profile. It is coded in a bitmap representation with 1 or more bits set. A bit set to '1' means that the xTUs may apply the respective coding for the DSL line. A bit set to '0' means that the xTUs cannot apply the respective coding for the ADSL line. All 'reserved' bits should be set to '0'." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.1 (XTSE)" ::= { xdsl2LineConfProfEntry 29 } xdsl2LConfProfPmMode OBJECT-TYPE SYNTAX Xdsl2LinePmMode -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- allowTransitionsToIdle(0) -- allowTransitionsToLowPower(1) ACCESS read-write STATUS mandatory DESCRIPTION "Power management state Enabling (PMMode). Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. This is a set of bits, where any bit with a '1' value means that the xTU is allowed to transit into the respective state and any bit with a '0' value means that the xTU is not allowed to transit into the respective state." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.4 (PMMode)" DEFVAL { 'c0'h } ::= { xdsl2LineConfProfEntry 30 } xdsl2LConfProfL0Time OBJECT-TYPE SYNTAX Gauge(0..255) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "The minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.5 (L0-TIME)" DEFVAL { 255 } ::= { xdsl2LineConfProfEntry 31 } xdsl2LConfProfL2Time OBJECT-TYPE SYNTAX Gauge(0..255) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "The minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 state. It ranges from 0 to 255 seconds." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.6 (L2-TIME)" DEFVAL { 255 } ::= { xdsl2LineConfProfEntry 32 } xdsl2LConfProfL2Atpr OBJECT-TYPE SYNTAX Gauge(0..31) -- Units -- dB ACCESS read-write STATUS mandatory DESCRIPTION "The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.7 (L2-ATPR)" DEFVAL { 10 } ::= { xdsl2LineConfProfEntry 33 } xdsl2LConfProfL2Atprt OBJECT-TYPE SYNTAX Gauge(0..31) -- Units -- dB ACCESS read-write STATUS mandatory DESCRIPTION "The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Requests (i.e., at transition of L0 to L2 state) and Power Trims." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.9 (L2-ATPRT)" DEFVAL { 31 } ::= { xdsl2LineConfProfEntry 34 } xdsl2LConfProfProfiles OBJECT-TYPE SYNTAX Xdsl2LineProfiles -- Rsyntax OCTET STRING(SIZE(1..2)) -- BITS are: -- profile8a(0) -- profile8b(1) -- profile8c(2) -- profile8d(3) -- profile12a(4) -- profile12b(5) -- profile17a(6) -- profile30a(7) ACCESS read-write STATUS mandatory DESCRIPTION "The configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. It is coded in a bitmap representation (0 if not allowed, 1 if allowed)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.1.11 (PROFILES)" DEFVAL { 'ff'h } ::= { xdsl2LineConfProfEntry 35 } xdsl2LConfProfDpboEPsd OBJECT-TYPE SYNTAX Xdsl2PsdMaskDs -- Rsyntax OCTET STRING(SIZE(0..96)) ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as xdsl2LConfProfPsdMaskDs (PSDMASKds). The maximum number of breakpoints for xdsl2LConfProfDpboEPsd is 16." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOEPSD)" ::= { xdsl2LineConfProfEntry 36 } xdsl2LConfProfDpboEsEL OBJECT-TYPE SYNTAX Gauge(0..511) -- Units -- 0.5 dB ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this length. The electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. This parameter shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid. If this parameter is set to '0', the DPBO shall be disabled." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESEL)" DEFVAL { 0 } ::= { xdsl2LineConfProfEntry 37 } xdsl2LConfProfDpboEsCableModelA OBJECT-TYPE SYNTAX Gauge(0..640) -- Units -- 2^-8 ACCESS read-write STATUS mandatory DESCRIPTION "The E-side Cable Model parameter A (DPBOESCMA) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. The cable model is in terms of three scalars xdsl2LConfProfDpboEsCableModelA (DPBOESCMA), xdsl2LConfProfDpboEsCableModelB(DPBOESCMB), and xdsl2LConfProfDpboEsCableModelC (DPBOESCMC), that are used to estimate the frequency dependent loss of E-side cables calculated from the xdsl2LConfProfDpboEsEL (DPBOESEL) parameter. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2^-8. All values in the range are valid. This parameter is used only for G.993.2." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMA)" DEFVAL { 0 } ::= { xdsl2LineConfProfEntry 38 } xdsl2LConfProfDpboEsCableModelB OBJECT-TYPE SYNTAX Gauge(0..640) -- Units -- 2^-8 ACCESS read-write STATUS mandatory DESCRIPTION "The E-side Cable Model parameter B (DPBOESCMB) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. The cable model is in terms of three scalars dsl2LConfProfDpboEsCableModelA (DPBOESCMA), xdsl2LConfProfDpboEsCableModelB(DPBOESCMB), and xdsl2LConfProfDpboEsCableModelC (DPBOESCMC), that are used to estimate the frequency dependent loss of E-side cables calculated from the xdsl2LConfProfDpboEsEL (DPBOESEL) parameter. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2^-8. All values in the range are valid. This parameter is used only for G.993.2." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMB)" DEFVAL { 0 } ::= { xdsl2LineConfProfEntry 39 } xdsl2LConfProfDpboEsCableModelC OBJECT-TYPE SYNTAX Gauge(0..640) -- Units -- 2^-8 ACCESS read-write STATUS mandatory DESCRIPTION "The E-side Cable Model parameter C (DPBOESCMC) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. The cable model is in terms of three scalars xdsl2LConfProfDpboEsCableModelA (DPBOESCMA), xdsl2LConfProfDpboEsCableModelB(DPBOESCMB), and xdsl2LConfProfDpboEsCableModelC (DPBOESCMC), that are used to estimate the frequency dependent loss of E-side cables calculated from the xdsl2LConfProfDpboEsEL (DPBOESEL) parameter. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2^-8. All values in the range are valid. This parameter is used only for G.993.2." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMC)" DEFVAL { 0 } ::= { xdsl2LineConfProfEntry 40 } xdsl2LConfProfDpboMus OBJECT-TYPE SYNTAX Gauge(0..255) -- Units -- 0.5 dBm/Hz ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange-based services, used to modify parameter xdsl2LConfProfDpboFMax (DPBOFMAX) defined below (to determine the DPBO). It shall be coded as an unsigned integer representing a PSD mask level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. NOTE - The PSD mask level is 3.5 dB above the signal PSD level. This parameter is used only for G.993.2." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOMUS)" DEFVAL { 0 } ::= { xdsl2LineConfProfEntry 41 } xdsl2LConfProfDpboFMin OBJECT-TYPE SYNTAX Gauge(0..2048) -- Units -- 4.3125 kHz ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz (coded as 0) to 8832 kHz (coded as 2048) in steps of 4.3125 kHz. This parameter is used only for G.993.2." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMIN)" DEFVAL { 32 } ::= { xdsl2LineConfProfEntry 42 } xdsl2LConfProfDpboFMax OBJECT-TYPE SYNTAX Gauge(32..6956) -- Units -- 4.3125 kHz ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the maximum frequency at which DPBO may be applied. It ranges from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956) in steps of 4.3125 kHz. This parameter is used only for G.993.2." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMAX)" DEFVAL { 512 } ::= { xdsl2LineConfProfEntry 43 } xdsl2LConfProfUpboKL OBJECT-TYPE SYNTAX Gauge(0..1280) -- Units -- 0.1 dB ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the electrical length expressed in dB at 1 MHz, kl0, configured by the CO-MIB. The value ranges from 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. This parameter is relevant only if xdsl2LConfProfUpboKLF is set to 'override(2)', which indicates that this parameter's value will override the VTUs' determination of the electrical length. If xdsl2LConfProfUpboKLF is set either to auto(1) or disableUpbo(3), then this parameter will be ignored." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOKL)" DEFVAL { 0 } ::= { xdsl2LineConfProfEntry 44 } xdsl2LConfProfUpboKLF OBJECT-TYPE SYNTAX Xdsl2UpboKLF -- Rsyntax INTEGER { -- auto(1), -- override(2), -- disableUpbo(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Defines the upstream power backoff force mode." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOKLF) " DEFVAL { disableUpbo } ::= { xdsl2LineConfProfEntry 45 } xdsl2LConfProfUs0Mask OBJECT-TYPE SYNTAX Xdsl2LineUs0Mask -- Rsyntax OCTET STRING(SIZE(1..4)) -- BITS are: -- eu32(0) -- eu36(1) -- eu40(2) -- eu44(3) -- eu48(4) -- eu52(5) -- eu56(6) -- eu60(7) -- eu64(8) -- eu128(9) -- reserved1(10) -- reserved2(11) -- reserved3(12) -- reserved4(13) -- reserved5(14) -- reserved6(15) -- adlu32(16) -- adlu36(17) -- adlu40(18) -- adlu44(19) -- adlu48(20) -- adlu52(21) -- adlu56(22) -- adlu60(23) -- adlu64(24) -- adlu128(25) -- reserved7(26) -- reserved8(27) -- reserved9(28) -- reserved10(29) -- reserved11(30) -- reserved12(31) ACCESS read-write STATUS mandatory DESCRIPTION "The configuration parameter contains the US0 PSD masks to be allowed by the near-end xTU on the line. This parameter is only defined for G.993.2 Annex A. It is represented as a bitmap (0 if not allowed and 1 if allowed)." REFERENCE "ITU-T G.997.1 Amendment 1, paragraph #7.3.1.2.18 (US0MASK)" DEFVAL { '00000000'h } ::= { xdsl2LineConfProfEntry 46 } xdsl2LConfProfForceInp OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter, when set to 'true' indicates that the framer settings of the bearer shall be selected such that the impulse noise protection computed according to the formula specified in the relevant Recommendation is greater than or equal to the minimal impulse noise protection requirement. This flag shall have the same value for all the bearers of one line in the same direction." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.5 (FORCEINP)" DEFVAL { false } ::= { xdsl2LineConfProfEntry 47 } xdsl2LConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all templates. A row in this table is said to be unreferenced when there is no instance of xdsl2LConfTempLineProfile that refers to the row. When a row is created in this table, the SNMP agent should also create corresponding rows in the tables xdsl2LineConfProfModeSpecTable and xdsl2LineConfProfModeSpecBandUsTable. When a row is deleted in this table, the SNMP agent should also delete corresponding rows in the tables xdsl2LineConfProfModeSpecTable and xdsl2LineConfProfModeSpecBandUsTable." ::= { xdsl2LineConfProfEntry 48 } xdsl2LineConfProfModeSpecTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineConfProfModeSpecEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineConfProfModeSpecTable extends the DSL line configuration profile by xDSL Mode-Specific parameters. A row in this table that has an index of xdsl2LConfProfXdslMode == defMode(1), is called a 'mandatory' row or 'default' row. A row in this table that has an index such that xdsl2LConfProfXdslMode is not equal to defMode(1), is called an 'optional' row or 'mode-specific' row. When a row in the xdsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the xdsl2LConfProfModeSpecRowStatus object will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the xdsl2LConfProfModeSpecRowStatus object if the parent row exists. The manager MAY delete an 'optional' row in this table using the xdsl2LConfProfModeSpecRowStatus object at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileLine 3 } xdsl2LineConfProfModeSpecEntry OBJECT-TYPE SYNTAX Xdsl2LineConfProfModeSpecEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineConfProfModeSpecTable extends the DSL line configuration profile by DSL Mode-Specific parameters." INDEX { xdsl2LConfProfProfileName, xdsl2LConfProfXdslMode } ::= { xdsl2LineConfProfModeSpecTable 1 } Xdsl2LineConfProfModeSpecEntry ::= SEQUENCE { xdsl2LConfProfXdslMode Xdsl2OperationModes, xdsl2LConfProfMaxNomPsdDs INTEGER, xdsl2LConfProfMaxNomPsdUs INTEGER, xdsl2LConfProfMaxNomAtpDs Gauge, xdsl2LConfProfMaxNomAtpUs Gauge, xdsl2LConfProfMaxAggRxPwrUs INTEGER, xdsl2LConfProfPsdMaskDs Xdsl2PsdMaskDs, xdsl2LConfProfPsdMaskUs Xdsl2PsdMaskUs, xdsl2LConfProfPsdMaskSelectUs Xdsl2LinePsdMaskSelectUs, xdsl2LConfProfClassMask Xdsl2LineClassMask, xdsl2LConfProfLimitMask Xdsl2LineLimitMask, xdsl2LConfProfUs0Disable Xdsl2LineUs0Disable, xdsl2LConfProfModeSpecRowStatus RowStatus } xdsl2LConfProfXdslMode OBJECT-TYPE SYNTAX Xdsl2OperationModes -- Rsyntax INTEGER { -- defMode(1), -- ansit1413(2), -- etsi(3), -- g9921PotsNonOverlapped(4), -- g9921PotsOverlapped(5), -- g9921IsdnNonOverlapped(6), -- g9921isdnOverlapped(7), -- g9921tcmIsdnNonOverlapped(8), -- g9921tcmIsdnOverlapped(9), -- g9922potsNonOverlapped(10), -- g9922potsOverlapped(11), -- g9922tcmIsdnNonOverlapped(12), -- g9922tcmIsdnOverlapped(13), -- g9921tcmIsdnSymmetric(14), -- g9923PotsNonOverlapped(20), -- g9923PotsOverlapped(21), -- g9923IsdnNonOverlapped(22), -- g9923isdnOverlapped(23), -- g9924potsNonOverlapped(26), -- g9924potsOverlapped(27), -- g9923AnnexIAllDigNonOverlapped(30), -- g9923AnnexIAllDigOverlapped(31), -- g9923AnnexJAllDigNonOverlapped(32), -- g9923AnnexJAllDigOverlapped(33), -- g9924AnnexIAllDigNonOverlapped(34), -- g9924AnnexIAllDigOverlapped(35), -- g9923AnnexLMode1NonOverlapped(36), -- g9923AnnexLMode2NonOverlapped(37), -- g9923AnnexLMode3Overlapped(38), -- g9923AnnexLMode4Overlapped(39), -- g9923AnnexMPotsNonOverlapped(40), -- g9923AnnexMPotsOverlapped(41), -- g9925PotsNonOverlapped(42), -- g9925PotsOverlapped(43), -- g9925IsdnNonOverlapped(44), -- g9925isdnOverlapped(45), -- g9925AnnexIAllDigNonOverlapped(48), -- g9925AnnexIAllDigOverlapped(49), -- g9925AnnexJAllDigNonOverlapped(50), -- g9925AnnexJAllDigOverlapped(51), -- g9925AnnexMPotsNonOverlapped(52), -- g9925AnnexMPotsOverlapped(53), -- g9932AnnexA(58), -- g9932AnnexB(59), -- g9932AnnexC(60) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The DSL Mode is a way of categorizing the various xDSL transmission modes into groups, each group (xDSL Mode) shares the same PSD configuration. There should be multiple entries in this table for a given line profile in case multiple bits are set in xdsl2LConfProfXtuTransSysEna for that profile." REFERENCE "DSL Forum TR-129, paragraph #5.5" ::= { xdsl2LineConfProfModeSpecEntry 1 } xdsl2LConfProfMaxNomPsdDs OBJECT-TYPE SYNTAX INTEGER(-600..-300) -- Units -- 0.1 dBm/Hz ACCESS read-write STATUS mandatory DESCRIPTION "The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.1 (MAXNOMPSDds)" DEFVAL { -300 } ::= { xdsl2LineConfProfModeSpecEntry 2 } xdsl2LConfProfMaxNomPsdUs OBJECT-TYPE SYNTAX INTEGER(-600..-300) -- Units -- 0.1 dBm/Hz ACCESS read-write STATUS mandatory DESCRIPTION "The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.2 (MAXNOMPSDus)" DEFVAL { -300 } ::= { xdsl2LineConfProfModeSpecEntry 3 } xdsl2LConfProfMaxNomAtpDs OBJECT-TYPE SYNTAX Gauge(0..255) -- Units -- 0.1 dBm ACCESS read-write STATUS mandatory DESCRIPTION "The maximum nominal aggregate to transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.3 (MAXNOMATPds)" DEFVAL { 255 } ::= { xdsl2LineConfProfModeSpecEntry 4 } xdsl2LConfProfMaxNomAtpUs OBJECT-TYPE SYNTAX Gauge(0..255) -- Units -- 0.1 dBm ACCESS read-write STATUS mandatory DESCRIPTION "The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.4 (MAXNOMATPus)" DEFVAL { 255 } ::= { xdsl2LineConfProfModeSpecEntry 5 } xdsl2LConfProfMaxAggRxPwrUs OBJECT-TYPE SYNTAX INTEGER(-255..255|2147483647) -- Units -- 0.1 dBm ACCESS read-write STATUS mandatory DESCRIPTION "The maximum upstream aggregate receive power over the relevant set of subcarriers. The xTU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges from -255 to 255 units of 0.1 dBm (physical values are -25.5 to 25.5 dBm). A value of 0x7FFFFFFF (2147483647) means that there is no limit." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.5 (MAXRXPWRus)" DEFVAL { 255 } ::= { xdsl2LineConfProfModeSpecEntry 6 } xdsl2LConfProfPsdMaskDs OBJECT-TYPE SYNTAX Xdsl2PsdMaskDs -- Rsyntax OCTET STRING(SIZE(0..96)) ACCESS read-write STATUS mandatory DESCRIPTION "The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0-1 - Index of the first subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a second breakpoint. Octets 6-8 - Same, for a third breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCds-1. Each PSD reduction value is in the range 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) with steps of 0.5 dBm/Hz. Valid values are in the range 0 to 190 (0 to -95 dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value '0'. Note that the content of this object should be correlated with the subcarrier mask and with the RFI setup." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.9 (PSDMASKds)" ::= { xdsl2LineConfProfModeSpecEntry 7 } xdsl2LConfProfPsdMaskUs OBJECT-TYPE SYNTAX Xdsl2PsdMaskUs -- Rsyntax OCTET STRING(SIZE(0..48)) ACCESS read-write STATUS mandatory DESCRIPTION "The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 16 pairs of values in the following structure: Octets 0-1 - Index of the first subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a second breakpoint. Octets 6-8 - Same, for a third breakpoint. This architecture continues until octets 9-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCus-1. Each PSD reduction value is in the range 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) with steps of 0.5 dBm/Hz. Valid values are in the range 0 to 190 (0 to -95 dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value '0'. Note that the content of this object should be correlated with the subcarrier mask and with the RFI setup." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.12 (PSDMASKus)" ::= { xdsl2LineConfProfModeSpecEntry 8 } xdsl2LConfProfPsdMaskSelectUs OBJECT-TYPE SYNTAX Xdsl2LinePsdMaskSelectUs -- Rsyntax INTEGER { -- adlu32Eu32(1), -- adlu36Eu36(2), -- adlu40Eu40(3), -- adlu44Eu44(4), -- adlu48Eu48(5), -- adlu52Eu52(6), -- adlu56Eu56(7), -- adlu60Eu60(8), -- adlu64Eu64(9) -- } ACCESS read-write STATUS mandatory DESCRIPTION "The selected upstream PSD mask. This parameter is used only for Annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in xdsl2LConfProfXtuTransSysEna." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.11 (Upstream PSD mask selection)" DEFVAL { adlu32Eu32 } ::= { xdsl2LineConfProfModeSpecEntry 9 } xdsl2LConfProfClassMask OBJECT-TYPE SYNTAX Xdsl2LineClassMask -- Rsyntax INTEGER { -- none(1), -- a998ORb997M1cORc998B(2), -- b997M1xOR998co(3), -- b997M2x(4), -- b998M1x(5), -- b998M2x(6), -- b998AdeM2x(7), -- bHpeM1(8) -- } ACCESS read-write STATUS mandatory DESCRIPTION "In order to reduce the number of configuration possibilities, the limit Power Spectral Density masks (see LIMITMASK) are grouped in PSD mask classes. Each class is designed such that the PSD levels of each limit PSD mask of a specific class are equal in their respective passband above 552 kHz. This parameter is defined per VDSL2 Annex enabled in the xdsl2LConfProfXtuTransSysEna object. It selects a single PSD mask class per Annex that is activated at the VTU-O." REFERENCE "ITU-T G.997.1 Amendment 1, paragraph #7.3.1.2.15 (CLASSMASK)" DEFVAL { a998ORb997M1cORc998B } ::= { xdsl2LineConfProfModeSpecEntry 10 } xdsl2LConfProfLimitMask OBJECT-TYPE SYNTAX Xdsl2LineLimitMask -- Rsyntax OCTET STRING(SIZE(1..8)) -- BITS are: -- profile8Limit1(0) -- profile8Limit2(1) -- profile8Limit3(2) -- profile8Limit4(3) -- profile8Limit5(4) -- profile8Limit6(5) -- profile8Limit7(6) -- profile8Limit8(7) -- profile8Limit9(8) -- profile8Limit10(9) -- profile8Limit11(10) -- profile8Limit12(11) -- profile8Limit13(12) -- profile8Limit14(13) -- profile8Limit15(14) -- profile8Limit16(15) -- profile12Limit1(16) -- profile12Limit2(17) -- profile12Limit3(18) -- profile12Limit4(19) -- profile12Limit5(20) -- profile12Limit6(21) -- profile12Limit7(22) -- profile12Limit8(23) -- profile12Limit9(24) -- profile12Limit10(25) -- profile12Limit11(26) -- profile12Limit12(27) -- profile12Limit13(28) -- profile12Limit14(29) -- profile12Limit15(30) -- profile12Limit16(31) -- profile17Limit1(32) -- profile17Limit2(33) -- profile17Limit3(34) -- profile17Limit4(35) -- profile17Limit5(36) -- profile17Limit6(37) -- profile17Limit7(38) -- profile17Limit8(39) -- profile17Limit9(40) -- profile17Limit10(41) -- profile17Limit11(42) -- profile17Limit12(43) -- profile17Limit13(44) -- profile17Limit14(45) -- profile17Limit15(46) -- profile17Limit16(47) -- profile30Limit1(48) -- profile30Limit2(49) -- profile30Limit3(50) -- profile30Limit4(51) -- profile30Limit5(52) -- profile30Limit6(53) -- profile30Limit7(54) -- profile30Limit8(55) -- profile30Limit9(56) -- profile30Limit10(57) -- profile30Limit11(58) -- profile30Limit12(59) -- profile30Limit13(60) -- profile30Limit14(61) -- profile30Limit15(62) -- profile30Limit16(63) ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter contains the G.993.2 limit PSD masks of the selected PSD mask class, enabled by the near-end xTU on this line for each class of profiles. This parameter is defined per VDSL2 Annex enabled in the xdsl2LConfProfXtuTransSysEna object. Through this parameter, several limit PSD masks of the selected PSD mask class (xdsl2LConfProfClassMask) may be enabled. The enabling parameter is coded in a bitmap representation (0 if the associated mask is not allowed, 1 if it is allowed)." REFERENCE "ITU-T G.997.1 Amendment 1, paragraph #7.3.1.2.16 (LIMITMASK)" DEFVAL { '0000000000000000'h } ::= { xdsl2LineConfProfModeSpecEntry 11 } xdsl2LConfProfUs0Disable OBJECT-TYPE SYNTAX Xdsl2LineUs0Disable -- Rsyntax OCTET STRING(SIZE(1..8)) -- BITS are: -- profile8Us0Disable1(0) -- profile8Us0Disable2(1) -- profile8Us0Disable3(2) -- profile8Us0Disable4(3) -- profile8Us0Disable5(4) -- profile8Us0Disable6(5) -- profile8Us0Disable7(6) -- profile8Us0Disable8(7) -- profile8Us0Disable9(8) -- profile8Us0Disable10(9) -- profile8Us0Disable11(10) -- profile8Us0Disable12(11) -- profile8Us0Disable13(12) -- profile8Us0Disable14(13) -- profile8Us0Disable15(14) -- profile8Us0Disable16(15) -- profile12Us0Disable1(16) -- profile12Us0Disable2(17) -- profile12Us0Disable3(18) -- profile12Us0Disable4(19) -- profile12Us0Disable5(20) -- profile12Us0Disable6(21) -- profile12Us0Disable7(22) -- profile12Us0Disable8(23) -- profile12Us0Disable9(24) -- profile12Us0Disable10(25) -- profile12Us0Disable11(26) -- profile12Us0Disable12(27) -- profile12Us0Disable13(28) -- profile12Us0Disable14(29) -- profile12Us0Disable15(30) -- profile12Us0Disable16(31) -- profile17Us0Disable1(32) -- profile17Us0Disable2(33) -- profile17Us0Disable3(34) -- profile17Us0Disable4(35) -- profile17Us0Disable5(36) -- profile17Us0Disable6(37) -- profile17Us0Disable7(38) -- profile17Us0Disable8(39) -- profile17Us0Disable9(40) -- profile17Us0Disable10(41) -- profile17Us0Disable11(42) -- profile17Us0Disable12(43) -- profile17Us0Disable13(44) -- profile17Us0Disable14(45) -- profile17Us0Disable15(46) -- profile17Us0Disable16(47) -- profile30Us0Disable1(48) -- profile30Us0Disable2(49) -- profile30Us0Disable3(50) -- profile30Us0Disable4(51) -- profile30Us0Disable5(52) -- profile30Us0Disable6(53) -- profile30Us0Disable7(54) -- profile30Us0Disable8(55) -- profile30Us0Disable9(56) -- profile30Us0Disable10(57) -- profile30Us0Disable11(58) -- profile30Us0Disable12(59) -- profile30Us0Disable13(60) -- profile30Us0Disable14(61) -- profile30Us0Disable15(62) -- profile30Us0Disable16(63) ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter indicates if the use of the US0 is disabled for each limit PSD mask enabled in the xdsl2LConfProfLimitMask parameter. This parameter is defined per VDSL2 Annex enabled in the xdsl2LConfProfXtuTransSysEna object. For each limit PSD mask enabled in the xdsl2LConfProfLimitMask parameter, a bit shall indicate if the US0 is disabled. The disabling parameter is coded as a bitmap. The bit is set to '1' if the US0 is disabled for the associated limit mask. This parameter and the xdsl2LConfProfLimitMask parameter use the same structure." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.17 (US0DISABLE)" DEFVAL { '0000000000000000'h } ::= { xdsl2LineConfProfModeSpecEntry 12 } xdsl2LConfProfModeSpecRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. This row is activated by setting this object to 'active'. A 'mandatory' row, as defined in the DESCRIPTION clause of xdsl2LineConfProfModeSpecTable, cannot be deleted at all. A 'mandatory' row can be taken out of service (by setting this object to 'notInService') if the parent row in the xdsl2LineConfProfTable table is not in the 'active' state. An 'optional' row (or 'mode-specific' row) can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService') at any time." ::= { xdsl2LineConfProfModeSpecEntry 13 } xdsl2LineConfProfModeSpecBandUsTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineConfProfModeSpecBandUsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineConfProfModeSpecBandUsTable extends xdsl2LineConfProfModeSpecTable with upstream-band-specific parameters for VDSL2, such as upstream power back-off parameters xdsl2LConfProfUpboPsdA and xdsl2LConfProfUpboPsdB (UPBOPSD-pb). When a parent 'mandatory row' is created in xdsl2LineConfProfModeSpecTable, the SNMP agent will automatically create several 'mandatory' rows in this table -- one for each upstream band: Note: A mandatory row is one where xdsl2LConfProfXdslMode = defMode(1). When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete a 'mandatory' row using the xdsl2LConfProfModeSpecBandUsRowStatus object will be rejected by the SNMP agent. The manager MAY create a new 'optional' row in this table using the xdsl2LConfProfModeSpecBandUsRowStatus object if the associated parent row exists, and the value of xdsl2LConfProfXdslMode is a G.993.2 value. The manager MAY delete an 'optional' row in this table using the xdsl2LConfProfModeSpecBandUsRowStatus object at any time. With respect to the xdsl2LConfProfUpboPsdA and xdsl2LConfProfUpboPsdB parameters, for a given upstream band, if an optional row is missing from this table, then that means upstream power back-off is disabled for that upstream band. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileLine 4 } xdsl2LineConfProfModeSpecBandUsEntry OBJECT-TYPE SYNTAX Xdsl2LineConfProfModeSpecBandUsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineConfProfModeSpecBandUsTable extends xdsl2LineConfProfModeSpecTable with upstream-band-specific parameters for VDSL2, such as upstream power back-off parameters xdsl2LConfProfUpboPsdA and xdsl2LConfProfUpboPsdB (UPBOPSD- pb)." INDEX { xdsl2LConfProfProfileName, xdsl2LConfProfXdslMode, xdsl2LConfProfXdslBandUs } ::= { xdsl2LineConfProfModeSpecBandUsTable 1 } Xdsl2LineConfProfModeSpecBandUsEntry ::= SEQUENCE { xdsl2LConfProfXdslBandUs Xdsl2BandUs, xdsl2LConfProfUpboPsdA INTEGER, xdsl2LConfProfUpboPsdB INTEGER, xdsl2LConfProfModeSpecBandUsRowStatus RowStatus } xdsl2LConfProfXdslBandUs OBJECT-TYPE SYNTAX Xdsl2BandUs -- Rsyntax INTEGER { -- us1(5), -- us2(7), -- us3(9), -- us4(11) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "Each value identifies a specific band in the upstream transmission direction (excluding the US0 band)." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.14" ::= { xdsl2LineConfProfModeSpecBandUsEntry 1 } xdsl2LConfProfUpboPsdA OBJECT-TYPE SYNTAX INTEGER(4000..8095) -- Units -- 0.01 dBm/Hz ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb)" DEFVAL { 4000 } ::= { xdsl2LineConfProfModeSpecBandUsEntry 2 } xdsl2LConfProfUpboPsdB OBJECT-TYPE SYNTAX INTEGER(0..4095) -- Units -- 0.01 dBm/Hz ACCESS read-write STATUS mandatory DESCRIPTION "This configuration parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band." REFERENCE "ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb)" DEFVAL { 0 } ::= { xdsl2LineConfProfModeSpecBandUsEntry 3 } xdsl2LConfProfModeSpecBandUsRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. This row is activated by setting this object to 'active'. A 'mandatory' row, as defined in the DESCRIPTION clause of xdsl2LineConfProfModeSpecBandUsTable, cannot be deleted at all. A 'mandatory' row can be taken out of service (by setting this object to 'notInService') if the parent row in the xdsl2LineConfProfModeSpecTable table is not in the 'active' state. An 'optional' row (or 'mode-specific' row) can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService') at any time." ::= { xdsl2LineConfProfModeSpecBandUsEntry 4 } xdsl2ChConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2ChConfProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2ChConfProfileTable contains DSL channel profile configuration. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileChannel 1 } xdsl2ChConfProfileEntry OBJECT-TYPE SYNTAX Xdsl2ChConfProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this document." INDEX { xdsl2ChConfProfProfileName } ::= { xdsl2ChConfProfileTable 1 } Xdsl2ChConfProfileEntry ::= SEQUENCE { xdsl2ChConfProfProfileName SnmpAdminString, xdsl2ChConfProfMinDataRateDs Gauge, xdsl2ChConfProfMinDataRateUs Gauge, xdsl2ChConfProfMinResDataRateDs Gauge, xdsl2ChConfProfMinResDataRateUs Gauge, xdsl2ChConfProfMaxDataRateDs Gauge, xdsl2ChConfProfMaxDataRateUs Gauge, xdsl2ChConfProfMinDataRateLowPwrDs Gauge, xdsl2ChConfProfMinDataRateLowPwrUs Gauge, xdsl2ChConfProfMaxDelayDs Gauge, xdsl2ChConfProfMaxDelayUs Gauge, xdsl2ChConfProfMinProtectionDs Xdsl2SymbolProtection, xdsl2ChConfProfMinProtectionUs Xdsl2SymbolProtection, xdsl2ChConfProfMinProtection8Ds Xdsl2SymbolProtection8, xdsl2ChConfProfMinProtection8Us Xdsl2SymbolProtection8, xdsl2ChConfProfMaxBerDs Xdsl2MaxBer, xdsl2ChConfProfMaxBerUs Xdsl2MaxBer, xdsl2ChConfProfUsDataRateDs Gauge, xdsl2ChConfProfDsDataRateDs Gauge, xdsl2ChConfProfUsDataRateUs Gauge, xdsl2ChConfProfDsDataRateUs Gauge, xdsl2ChConfProfImaEnabled TruthValue, xdsl2ChConfProfMaxDelayVar Gauge, xdsl2ChConfProfInitPolicy Xdsl2ChInitPolicy, xdsl2ChConfProfRowStatus RowStatus } xdsl2ChConfProfProfileName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This object identifies a row in this table." ::= { xdsl2ChConfProfileEntry 1 } xdsl2ChConfProfMinDataRateDs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Minimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.1 (Minimum data rate)" ::= { xdsl2ChConfProfileEntry 2 } xdsl2ChConfProfMinDataRateUs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Minimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.1 (Minimum data rate)" ::= { xdsl2ChConfProfileEntry 3 } xdsl2ChConfProfMinResDataRateDs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., xdsl2LConfProfRaModeDs) is set to 'dynamicRa'." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.2 (Minimum reserved data rate)" ::= { xdsl2ChConfProfileEntry 4 } xdsl2ChConfProfMinResDataRateUs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., xdsl2LConfProfRaModeUs) is set to 'dynamicRa'." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.2 (Minimum reserved data rate)" ::= { xdsl2ChConfProfileEntry 5 } xdsl2ChConfProfMaxDataRateDs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.3 (Maximum data rate)" ::= { xdsl2ChConfProfileEntry 6 } xdsl2ChConfProfMaxDataRateUs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.3 (Maximum data rate)" ::= { xdsl2ChConfProfileEntry 7 } xdsl2ChConfProfMinDataRateLowPwrDs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "This parameter specifies the minimum net data rate for the bearer channel as desired by the operator of the system during the low power state (L1/L2). The power management low power states L1 and L2 are defined in ITU-T Recommendations G.992.2 and G.992.3, respectively. The data rate is coded in steps of bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.5 (Minimum Data Rate in low power state)" ::= { xdsl2ChConfProfileEntry 8 } xdsl2ChConfProfMinDataRateLowPwrUs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "This parameter specifies the minimum net data rate for the bearer channel as desired by the operator of the system during the low power state (L1/L2). The power management low power states L1 and L2 are defined in ITU-T Recommendations G.992.2 and G.992.3, respectively. The data rate is coded in steps of bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.1.5 (Minimum Data Rate in low power state)" ::= { xdsl2ChConfProfileEntry 9 } xdsl2ChConfProfMaxDelayDs OBJECT-TYPE SYNTAX Gauge(0..63) -- Units -- milliseconds ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The xTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Xdsl2ChStatusActDelay) is as close as possible to, but less than or equal to, xdsl2ChConfProfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.2 (Maximum interleaving delay)" ::= { xdsl2ChConfProfileEntry 10 } xdsl2ChConfProfMaxDelayUs OBJECT-TYPE SYNTAX Gauge(0..63) -- Units -- milliseconds ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The xTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Xdsl2ChStatusActDelay) is as close as possible to, but less than or equal to, xdsl2ChConfProfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.2 (Maximum interleaving delay)" ::= { xdsl2ChConfProfileEntry 11 } xdsl2ChConfProfMinProtectionDs OBJECT-TYPE SYNTAX Xdsl2SymbolProtection -- Rsyntax INTEGER { -- noProtection(1), -- halfSymbol(2), -- singleSymbol(3), -- twoSymbols(4), -- threeSymbols(5), -- fourSymbols(6), -- fiveSymbols(7), -- sixSymbols(8), -- sevenSymbols(9), -- eightSymbols(10), -- nineSymbols(11), -- tenSymbols(12), -- elevenSymbols(13), -- twelveSymbols(14), -- thirteeSymbols(15), -- fourteenSymbols(16), -- fifteenSymbols(17), -- sixteenSymbols(18) -- } -- Units -- symbols ACCESS read-write STATUS mandatory DESCRIPTION "This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take the values 1/2 and any integer from 0 to 16, inclusive. If the xTU does not support the configured INPMIN value, it shall use the nearest supported impulse noise protection greater than INPMIN." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.3 (INPMINds)" DEFVAL { noProtection } ::= { xdsl2ChConfProfileEntry 12 } xdsl2ChConfProfMinProtectionUs OBJECT-TYPE SYNTAX Xdsl2SymbolProtection -- Rsyntax INTEGER { -- noProtection(1), -- halfSymbol(2), -- singleSymbol(3), -- twoSymbols(4), -- threeSymbols(5), -- fourSymbols(6), -- fiveSymbols(7), -- sixSymbols(8), -- sevenSymbols(9), -- eightSymbols(10), -- nineSymbols(11), -- tenSymbols(12), -- elevenSymbols(13), -- twelveSymbols(14), -- thirteeSymbols(15), -- fourteenSymbols(16), -- fifteenSymbols(17), -- sixteenSymbols(18) -- } -- Units -- symbols ACCESS read-write STATUS mandatory DESCRIPTION "This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take the values 1/2 and any integer from 0 to 16, inclusive. If the xTU does not support the configured INPMIN value, it shall use the nearest supported impulse noise protection greater than INPMIN." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.3 (INPMINus)" DEFVAL { noProtection } ::= { xdsl2ChConfProfileEntry 13 } xdsl2ChConfProfMinProtection8Ds OBJECT-TYPE SYNTAX Xdsl2SymbolProtection8 -- Rsyntax INTEGER { -- noProtection(1), -- singleSymbol(2), -- twoSymbols(3), -- threeSymbols(4), -- fourSymbols(5), -- fiveSymbols(6), -- sixSymbols(7), -- sevenSymbols(8), -- eightSymbols(9), -- nineSymbols(10), -- tenSymbols(11), -- elevenSymbols(12), -- twelveSymbols(13), -- thirteeSymbols(14), -- fourteenSymbols(15), -- fifteenSymbols(16), -- sixteenSymbols(17) -- } -- Units -- symbols ACCESS read-write STATUS mandatory DESCRIPTION "This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.4 (INPMIN8ds)" DEFVAL { noProtection } ::= { xdsl2ChConfProfileEntry 14 } xdsl2ChConfProfMinProtection8Us OBJECT-TYPE SYNTAX Xdsl2SymbolProtection8 -- Rsyntax INTEGER { -- noProtection(1), -- singleSymbol(2), -- twoSymbols(3), -- threeSymbols(4), -- fourSymbols(5), -- fiveSymbols(6), -- sixSymbols(7), -- sevenSymbols(8), -- eightSymbols(9), -- nineSymbols(10), -- tenSymbols(11), -- elevenSymbols(12), -- twelveSymbols(13), -- thirteeSymbols(14), -- fourteenSymbols(15), -- fifteenSymbols(16), -- sixteenSymbols(17) -- } -- Units -- symbols ACCESS read-write STATUS mandatory DESCRIPTION "This parameter specifies the minimum impulse noise protection for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.4 (INPMIN8us)" DEFVAL { noProtection } ::= { xdsl2ChConfProfileEntry 15 } xdsl2ChConfProfMaxBerDs OBJECT-TYPE SYNTAX Xdsl2MaxBer -- Rsyntax INTEGER { -- eminus3(1), -- eminus5(2), -- eminus7(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.6 (Maximum bit error ratio)" DEFVAL { eminus5 } ::= { xdsl2ChConfProfileEntry 16 } xdsl2ChConfProfMaxBerUs OBJECT-TYPE SYNTAX Xdsl2MaxBer -- Rsyntax INTEGER { -- eminus3(1), -- eminus5(2), -- eminus7(3) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Maximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.6 (Maximum bit error ratio)" DEFVAL { eminus5 } ::= { xdsl2ChConfProfileEntry 17 } xdsl2ChConfProfUsDataRateDs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Data Rate Threshold Upshift for Downstream direction. An 'Up-Shift rate change' event is triggered when the actual downstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.8.1 (Data rate threshold upshift)" ::= { xdsl2ChConfProfileEntry 18 } xdsl2ChConfProfDsDataRateDs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Data Rate Threshold Downshift for Downstream direction. A 'Down-Shift rate change' event is triggered when the actual downstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.8.2 (Data rate threshold downshift)" ::= { xdsl2ChConfProfileEntry 19 } xdsl2ChConfProfUsDataRateUs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Data Rate Threshold Upshift for Upstream direction. An 'Up-Shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.8.1 (Data rate threshold upshift)" ::= { xdsl2ChConfProfileEntry 20 } xdsl2ChConfProfDsDataRateUs OBJECT-TYPE SYNTAX Gauge -- Units -- bits/second ACCESS read-write STATUS mandatory DESCRIPTION "Data Rate Threshold Downshift for Upstream direction. A 'Down-Shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s." REFERENCE "ITU-T G.997.1, paragraph #7.3.2.8.2 (Data rate threshold downshift)" ::= { xdsl2ChConfProfileEntry 21 } xdsl2ChConfProfImaEnabled OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "IMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is of ATM Data Path. When in 'enable' state, the ATM Data Path should comply with the requirements for IMA transmission." REFERENCE "ITU-T G.997.1, paragraph #7.3.4.1 (IMA operation mode enable parameter)" DEFVAL { false } ::= { xdsl2ChConfProfileEntry 22 } xdsl2ChConfProfMaxDelayVar OBJECT-TYPE SYNTAX Gauge(1..255) -- Units -- 0.1 milliseconds ACCESS read-write STATUS mandatory DESCRIPTION "Maximum delay variation (DVMAX). This optional VDSL2-specific parameter specifies the maximum value for the delay variation allowed in an OLR procedure. It is ranges from 1 to 254 units of 0.1 milliseconds (i.e., 0.1 to 25.4 milliseconds) with the special value 255, which indicates that no delay variation bound is imposed." REFERENCE "ITU-T G.997.1 Amendment 1, paragraph #7.3.2.9 (DVMAX)" DEFVAL { 255 } ::= { xdsl2ChConfProfileEntry 23 } xdsl2ChConfProfInitPolicy OBJECT-TYPE SYNTAX Xdsl2ChInitPolicy -- Rsyntax INTEGER { -- policy0(1), -- policy1(2) -- } ACCESS read-write STATUS mandatory DESCRIPTION "Channel Initialization Policy Selection (CIPOLICY). This optional parameter indicates which policy shall be applied to determine the transceiver configuration parameters at initialization. Those policies are defined in the respective Recommendations." REFERENCE "ITU-T G.997.1 Amendment 1, paragraph #7.3.2.10 (CIPOLICY)" DEFVAL { policy0 } ::= { xdsl2ChConfProfileEntry 24 } xdsl2ChConfProfRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated templates. A row in xdsl2ChConfProfTable is said to be unreferenced when there is no instance of xdsl2LConfTempChan1ConfProfile, xdsl2LConfTempChan2ConfProfile, xdsl2LConfTempChan3ConfProfile, or xdsl2LConfTempChan4ConfProfile that refers to the row." ::= { xdsl2ChConfProfileEntry 25 } xdsl2LineAlarmConfTemplateTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineAlarmConfTemplateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineAlarConfTemplateTable contains DSL line alarm configuration templates. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileAlarmConf 1 } xdsl2LineAlarmConfTemplateEntry OBJECT-TYPE SYNTAX Xdsl2LineAlarmConfTemplateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A default template with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this document." INDEX { xdsl2LAlarmConfTempTemplateName } ::= { xdsl2LineAlarmConfTemplateTable 1 } Xdsl2LineAlarmConfTemplateEntry ::= SEQUENCE { xdsl2LAlarmConfTempTemplateName SnmpAdminString, xdsl2LAlarmConfTempLineProfile SnmpAdminString, xdsl2LAlarmConfTempChan1ConfProfile SnmpAdminString, xdsl2LAlarmConfTempChan2ConfProfile SnmpAdminString, xdsl2LAlarmConfTempChan3ConfProfile SnmpAdminString, xdsl2LAlarmConfTempChan4ConfProfile SnmpAdminString, xdsl2LAlarmConfTempRowStatus RowStatus } xdsl2LAlarmConfTempTemplateName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This object identifies a row in this table." ::= { xdsl2LineAlarmConfTemplateEntry 1 } xdsl2LAlarmConfTempLineProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the DSL Line Thresholds Configuration Profile Table (xdsl2LineAlarmConfProfileTable) that applies to this line." REFERENCE "DSL Forum TR-129, paragraph #8.2" DEFVAL { "DEFVAL" } ::= { xdsl2LineAlarmConfTemplateEntry 2 } xdsl2LAlarmConfTempChan1ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL bearer channel #1. The channel profile name specified here MUST match the name of an existing row in the xdsl2ChAlarmConfProfileTable table." REFERENCE "DSL Forum TR-129, paragraph #8.4" DEFVAL { "DEFVAL" } ::= { xdsl2LineAlarmConfTemplateEntry 3 } xdsl2LAlarmConfTempChan2ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL bearer channel #2. The channel profile name specified here MUST match the name of an existing row in the xdsl2ChAlarmConfProfileTable table. If the channel is unused, then the object is set to a zero-length string." REFERENCE "DSL Forum TR-129, paragraph #8.4" DEFVAL { "" } ::= { xdsl2LineAlarmConfTemplateEntry 4 } xdsl2LAlarmConfTempChan3ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL bearer channel #3. The channel profile name specified here MUST match the name of an existing row in the xdsl2ChAlarmConfProfileTable table. This object may be set to a non-zero-length string only if xdsl2LAlarmConfTempChan2ConfProfile contains a non-zero-length string." REFERENCE "DSL Forum TR-129, paragraph #8.4" DEFVAL { "" } ::= { xdsl2LineAlarmConfTemplateEntry 5 } xdsl2LAlarmConfTempChan4ConfProfile OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(0..32)) -- Rsyntax OCTET STRING(SIZE(0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "The value of this object identifies the row in the DSL Channel Thresholds Configuration Profile Table (xdsl2ChAlarmConfProfileTable) that applies for DSL bearer channel #4. The channel profile name specified here MUST match the name of an existing row in the xdsl2ChAlarmConfProfileTable table. This object may be set to a non-zero-length string only if xdsl2LAlarmConfTempChan3ConfProfile contains a non-zero-length string." REFERENCE "DSL Forum TR-129, paragraph #8.4" DEFVAL { "" } ::= { xdsl2LineAlarmConfTemplateEntry 6 } xdsl2LAlarmConfTempRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. Before a template can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated lines. A row in this table is said to be unreferenced when there is no instance of xdsl2LineAlarmConfTemplate that refers to the row." ::= { xdsl2LineAlarmConfTemplateEntry 7 } xdsl2LineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2LineAlarmConfProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2LineAlarmConfProfileTable contains DSL line performance threshold values. If a performance counter exceeds the threshold value specified in this table, then the SNMP agent will issue a threshold trap. Each performance counter has a unique trap type (see NOTIFICATION-TYPE definitions below). One trap will be sent per interval, per interface, per trap type. A value of 0 will disable the trap. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileAlarmConf 2 } xdsl2LineAlarmConfProfileEntry OBJECT-TYPE SYNTAX Xdsl2LineAlarmConfProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this document." INDEX { xdsl2LineAlarmConfProfileName } ::= { xdsl2LineAlarmConfProfileTable 1 } Xdsl2LineAlarmConfProfileEntry ::= SEQUENCE { xdsl2LineAlarmConfProfileName SnmpAdminString, xdsl2LineAlarmConfProfileXtucThresh15MinFecs HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXtucThresh15MinEs HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXtucThresh15MinSes HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXtucThresh15MinLoss HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXtucThresh15MinUas HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXturThresh15MinFecs HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXturThresh15MinEs HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXturThresh15MinSes HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXturThresh15MinLoss HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileXturThresh15MinUas HCPerfIntervalThreshold, xdsl2LineAlarmConfProfileThresh15MinFailedFullInt Gauge, xdsl2LineAlarmConfProfileThresh15MinFailedShrtInt Gauge, xdsl2LineAlarmConfProfileRowStatus RowStatus } xdsl2LineAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This object identifies a row in this table." ::= { xdsl2LineAlarmConfProfileEntry 1 } xdsl2LineAlarmConfProfileXtucThresh15MinFecs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MFecs counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 2 } xdsl2LineAlarmConfProfileXtucThresh15MinEs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MEs counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 3 } xdsl2LineAlarmConfProfileXtucThresh15MinSes OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MSes counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 4 } xdsl2LineAlarmConfProfileXtucThresh15MinLoss OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MLoss counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 5 } xdsl2LineAlarmConfProfileXtucThresh15MinUas OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MUas counter, when xdsl2PMLCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 6 } xdsl2LineAlarmConfProfileXturThresh15MinFecs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MFecs counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 7 } xdsl2LineAlarmConfProfileXturThresh15MinEs OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MEs counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 8 } xdsl2LineAlarmConfProfileXturThresh15MinSes OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MSes counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 9 } xdsl2LineAlarmConfProfileXturThresh15MinLoss OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MLoss counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 10 } xdsl2LineAlarmConfProfileXturThresh15MinUas OBJECT-TYPE SYNTAX HCPerfIntervalThreshold -- Rsyntax Gauge(0..900) -- Units -- seconds ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLCurr15MUas counter, when xdsl2PMLCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 11 } xdsl2LineAlarmConfProfileThresh15MinFailedFullInt OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLInitCurr15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 12 } xdsl2LineAlarmConfProfileThresh15MinFailedShrtInt OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMLInitCurr15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2LineAlarmConfProfileEntry 13 } xdsl2LineAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated templates. A row in this table is said to be unreferenced when there is no instance of xdsl2LAlarmConfTempLineProfile that refers to the row." ::= { xdsl2LineAlarmConfProfileEntry 14 } xdsl2ChAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2ChAlarmConfProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2ChAlarmConfProfileTable contains DSL channel performance threshold values. If a performance counter exceeds the threshold value specified in this table, then the SNMP agent will issue a threshold trap. Each performance counter has a unique trap type (see NOTIFICATION-TYPE definitions below). One trap will be sent per interval per interface per trap type. A value of 0 will disable the trap. Entries in this table MUST be maintained in a persistent manner." ::= { xdsl2ProfileAlarmConf 3 } xdsl2ChAlarmConfProfileEntry OBJECT-TYPE SYNTAX Xdsl2ChAlarmConfProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor-specific values, unless otherwise specified in this document." INDEX { xdsl2ChAlarmConfProfileName } ::= { xdsl2ChAlarmConfProfileTable 1 } Xdsl2ChAlarmConfProfileEntry ::= SEQUENCE { xdsl2ChAlarmConfProfileName SnmpAdminString, xdsl2ChAlarmConfProfileXtucThresh15MinCodingViolations Gauge, xdsl2ChAlarmConfProfileXtucThresh15MinCorrected Gauge, xdsl2ChAlarmConfProfileXturThresh15MinCodingViolations Gauge, xdsl2ChAlarmConfProfileXturThresh15MinCorrected Gauge, xdsl2ChAlarmConfProfileRowStatus RowStatus } xdsl2ChAlarmConfProfileName OBJECT-TYPE SYNTAX SnmpAdminString(SIZE(1..32)) -- Rsyntax OCTET STRING(SIZE(1..32)) ACCESS not-accessible STATUS mandatory DESCRIPTION "This object identifies a row in this table." ::= { xdsl2ChAlarmConfProfileEntry 1 } xdsl2ChAlarmConfProfileXtucThresh15MinCodingViolations OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMChCurr15MCodingViolations counter, when xdsl2PMChCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2ChAlarmConfProfileEntry 2 } xdsl2ChAlarmConfProfileXtucThresh15MinCorrected OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMChCurr15MCorrectedBlocks counter, when xdsl2PMChCurrUnit is xtuc {1}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2ChAlarmConfProfileEntry 3 } xdsl2ChAlarmConfProfileXturThresh15MinCodingViolations OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMChCurr15MCodingViolations counter, when xdsl2PMChCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2ChAlarmConfProfileEntry 4 } xdsl2ChAlarmConfProfileXturThresh15MinCorrected OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "A threshold for the xdsl2PMChCurr15MCorrectedBlocks counter, when xdsl2PMChCurrUnit is xtur {2}. The value 0 means that no threshold is specified for the associated counter." REFERENCE "ITU-T G.997.1, paragraph #7.2.7.2" DEFVAL { 0 } ::= { xdsl2ChAlarmConfProfileEntry 5 } xdsl2ChAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } ACCESS read-write STATUS mandatory DESCRIPTION "This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it MUST be first unreferenced from all associated templates. A row in xdsl2ChConfProfTable is said to be unreferenced when there is no instance of xdsl2LAlarmConfTempChan1ConfProfile, xdsl2LAlarmConfTempChan2ConfProfile, xdsl2LAlarmConfTempChan3ConfProfile, or xdsl2LAlarmConfTempChan4ConfProfile that refers to the row." ::= { xdsl2ChAlarmConfProfileEntry 6 } xdsl2PMLineCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMLineCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMLineCurrTable contains current Performance Monitoring results for DSL lines." ::= { xdsl2PMLine 1 } xdsl2PMLineCurrEntry OBJECT-TYPE SYNTAX Xdsl2PMLineCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the termination unit." INDEX { ifIndex, xdsl2PMLCurrUnit } ::= { xdsl2PMLineCurrTable 1 } Xdsl2PMLineCurrEntry ::= SEQUENCE { xdsl2PMLCurrUnit Xdsl2Unit, xdsl2PMLCurr15MValidIntervals Gauge, xdsl2PMLCurr15MInvalidIntervals Gauge, xdsl2PMLCurr15MTimeElapsed HCPerfTimeElapsed, xdsl2PMLCurr15MFecs Counter, xdsl2PMLCurr15MEs Counter, xdsl2PMLCurr15MSes Counter, xdsl2PMLCurr15MLoss Counter, xdsl2PMLCurr15MUas Counter, xdsl2PMLCurr1DayValidIntervals Gauge, xdsl2PMLCurr1DayInvalidIntervals Gauge, xdsl2PMLCurr1DayTimeElapsed HCPerfTimeElapsed, xdsl2PMLCurr1DayFecs Counter, xdsl2PMLCurr1DayEs Counter, xdsl2PMLCurr1DaySes Counter, xdsl2PMLCurr1DayLoss Counter, xdsl2PMLCurr1DayUas Counter } xdsl2PMLCurrUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2PMLineCurrEntry 1 } xdsl2PMLCurr15MValidIntervals OBJECT-TYPE SYNTAX Gauge(0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implementation is planned to store (i.e., beyond the scope of this MIB module) unless the measurement was (re-)started recently, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy), it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { xdsl2PMLineCurrEntry 2 } xdsl2PMLCurr15MInvalidIntervals OBJECT-TYPE SYNTAX Gauge(0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { xdsl2PMLineCurrEntry 3 } xdsl2PMLCurr15MTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed -- Rsyntax INTEGER(0..86399) -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total elapsed seconds in this interval." ::= { xdsl2PMLineCurrEntry 4 } xdsl2PMLCurr15MFecs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.1 (FECS-L) and paragraph #7.2.1.2.1 (FECS-LFE)" ::= { xdsl2PMLineCurrEntry 5 } xdsl2PMLCurr15MEs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.2 (ES-L) and paragraph #7.2.1.2.2 (ES-LFE)" ::= { xdsl2PMLineCurrEntry 6 } xdsl2PMLCurr15MSes OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or more of the received bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.3 (SES-L) and paragraph #7.2.1.2.3 (SES-LFE)" ::= { xdsl2PMLineCurrEntry 7 } xdsl2PMLCurr15MLoss OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R)." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.4 (LOSS-L) and paragraph #7.2.1.2.4 (LOSS-LFE)" ::= { xdsl2PMLineCurrEntry 8 } xdsl2PMLCurr15MUas OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored seconds." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.5 (UAS-L) and paragraph #7.2.1.2.5 (UAS-LFE)" ::= { xdsl2PMLineCurrEntry 9 } xdsl2PMLCurr1DayValidIntervals OBJECT-TYPE SYNTAX Gauge(0..30) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementation is planned to store (i.e., beyond the scope of this MIB module) unless the measurement was (re-)started recently, in which case the value will be the number of complete 24-hour intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy), it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { xdsl2PMLineCurrEntry 10 } xdsl2PMLCurr1DayInvalidIntervals OBJECT-TYPE SYNTAX Gauge(0..30) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { xdsl2PMLineCurrEntry 11 } xdsl2PMLCurr1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed -- Rsyntax INTEGER(0..86399) -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total elapsed seconds in this interval." ::= { xdsl2PMLineCurrEntry 12 } xdsl2PMLCurr1DayFecs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.1 (FECS-L) and paragraph #7.2.1.2.1 (FECS-LFE)" ::= { xdsl2PMLineCurrEntry 13 } xdsl2PMLCurr1DayEs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.2 (ES-L) and paragraph #7.2.1.2.2 (ES-LFE)" ::= { xdsl2PMLineCurrEntry 14 } xdsl2PMLCurr1DaySes OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or more of the received bearer channels) >= 18 OR LOS-FE >= 1. OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.3 (SES-L) and paragraph #7.2.1.2.3 (SES-LFE)" ::= { xdsl2PMLineCurrEntry 15 } xdsl2PMLCurr1DayLoss OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R)." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.4 (LOSS-L) and paragraph #7.2.1.2.4 (LOSS-LFE)" ::= { xdsl2PMLineCurrEntry 16 } xdsl2PMLCurr1DayUas OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored seconds." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.5 (UAS-L) and paragraph #7.2.1.2.5 (UAS-LFE)" ::= { xdsl2PMLineCurrEntry 17 } xdsl2PMLineInitCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMLineInitCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMLineInitCurrTable contains current initialization counters for DSL lines." ::= { xdsl2PMLine 2 } xdsl2PMLineInitCurrEntry OBJECT-TYPE SYNTAX Xdsl2PMLineInitCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The index of this table is an interface index where the interface has an ifType of vdsl2(251)." INDEX { ifIndex } ::= { xdsl2PMLineInitCurrTable 1 } Xdsl2PMLineInitCurrEntry ::= SEQUENCE { xdsl2PMLInitCurr15MValidIntervals Gauge, xdsl2PMLInitCurr15MInvalidIntervals Gauge, xdsl2PMLInitCurr15MTimeElapsed Gauge, xdsl2PMLInitCurr15MFullInits Gauge, xdsl2PMLInitCurr15MFailedFullInits Gauge, xdsl2PMLInitCurr15MShortInits Gauge, xdsl2PMLInitCurr15MFailedShortInits Gauge, xdsl2PMLInitCurr1DayValidIntervals Gauge, xdsl2PMLInitCurr1DayInvalidIntervals Gauge, xdsl2PMLInitCurr1DayTimeElapsed Gauge, xdsl2PMLInitCurr1DayFullInits Gauge, xdsl2PMLInitCurr1DayFailedFullInits Gauge, xdsl2PMLInitCurr1DayShortInits Gauge, xdsl2PMLInitCurr1DayFailedShortInits Gauge } xdsl2PMLInitCurr15MValidIntervals OBJECT-TYPE SYNTAX Gauge(0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implementation is planned to store (i.e., beyond the scope of this MIB module) unless the measurement was (re-)started recently, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy), it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { xdsl2PMLineInitCurrEntry 1 } xdsl2PMLInitCurr15MInvalidIntervals OBJECT-TYPE SYNTAX Gauge(0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { xdsl2PMLineInitCurrEntry 2 } xdsl2PMLInitCurr15MTimeElapsed OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total elapsed seconds in this interval." ::= { xdsl2PMLineInitCurrEntry 3 } xdsl2PMLInitCurr15MFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of full initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.1" ::= { xdsl2PMLineInitCurrEntry 4 } xdsl2PMLInitCurr15MFailedFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed full initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.2" ::= { xdsl2PMLineInitCurrEntry 5 } xdsl2PMLInitCurr15MShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of short initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.3" ::= { xdsl2PMLineInitCurrEntry 6 } xdsl2PMLInitCurr15MFailedShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed short initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.4" ::= { xdsl2PMLineInitCurrEntry 7 } xdsl2PMLInitCurr1DayValidIntervals OBJECT-TYPE SYNTAX Gauge(0..30) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementation is planned to store (i.e., beyond the scope of this MIB module) unless the measurement was (re-)started recently, in which case the value will be the number of complete 24-hour intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy), it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { xdsl2PMLineInitCurrEntry 8 } xdsl2PMLInitCurr1DayInvalidIntervals OBJECT-TYPE SYNTAX Gauge(0..30) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { xdsl2PMLineInitCurrEntry 9 } xdsl2PMLInitCurr1DayTimeElapsed OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total elapsed seconds in this interval." ::= { xdsl2PMLineInitCurrEntry 10 } xdsl2PMLInitCurr1DayFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of full initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.1" ::= { xdsl2PMLineInitCurrEntry 11 } xdsl2PMLInitCurr1DayFailedFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed full initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.2" ::= { xdsl2PMLineInitCurrEntry 12 } xdsl2PMLInitCurr1DayShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of short initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.3" ::= { xdsl2PMLineInitCurrEntry 13 } xdsl2PMLInitCurr1DayFailedShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed short initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.4" ::= { xdsl2PMLineInitCurrEntry 14 } xdsl2PMLineHist15MinTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMLineHist15MinEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMLineHist15MinTable contains PM line history for 15-minute intervals of DSL line." ::= { xdsl2PMLine 3 } xdsl2PMLineHist15MinEntry OBJECT-TYPE SYNTAX Xdsl2PMLineHist15MinEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission unit. The third index is the interval number." INDEX { ifIndex, xdsl2PMLHist15MUnit, xdsl2PMLHist15MInterval } ::= { xdsl2PMLineHist15MinTable 1 } Xdsl2PMLineHist15MinEntry ::= SEQUENCE { xdsl2PMLHist15MUnit Xdsl2Unit, xdsl2PMLHist15MInterval Gauge, xdsl2PMLHist15MMonitoredTime Gauge, xdsl2PMLHist15MFecs Counter, xdsl2PMLHist15MEs Counter, xdsl2PMLHist15MSes Counter, xdsl2PMLHist15MLoss Counter, xdsl2PMLHist15MUas Counter, xdsl2PMLHist15MValidInterval TruthValue } xdsl2PMLHist15MUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2PMLineHist15MinEntry 1 } xdsl2PMLHist15MInterval OBJECT-TYPE SYNTAX Gauge(1..96) ACCESS not-accessible STATUS mandatory DESCRIPTION "The interval number." ::= { xdsl2PMLineHist15MinEntry 2 } xdsl2PMLHist15MMonitoredTime OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total seconds monitored in this interval." ::= { xdsl2PMLineHist15MinEntry 3 } xdsl2PMLHist15MFecs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.1 (FECS-L) and paragraph #7.2.1.2.1 (FECS-LFE)" ::= { xdsl2PMLineHist15MinEntry 4 } xdsl2PMLHist15MEs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.2 (ES-L) and paragraph #7.2.1.2.2 (ES-LFE)" ::= { xdsl2PMLineHist15MinEntry 5 } xdsl2PMLHist15MSes OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or more of the received bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.3 (SES-L) and paragraph #7.2.1.2.3 (SES-LFE)" ::= { xdsl2PMLineHist15MinEntry 6 } xdsl2PMLHist15MLoss OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R)." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.4 (LOSS-L) and paragraph #7.2.1.2.4 (LOSS-LFE)" ::= { xdsl2PMLineHist15MinEntry 7 } xdsl2PMLHist15MUas OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored seconds." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.5 (UAS-L) and paragraph #7.2.1.2.5 (UAS-LFE)" ::= { xdsl2PMLineHist15MinEntry 8 } xdsl2PMLHist15MValidInterval OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { xdsl2PMLineHist15MinEntry 9 } xdsl2PMLineHist1DayTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMLineHist1DayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMLineHist1DayTable contains PM line history for 24-hour intervals of DSL line." ::= { xdsl2PMLine 4 } xdsl2PMLineHist1DayEntry OBJECT-TYPE SYNTAX Xdsl2PMLineHist1DayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index of this table is the transmission unit.The third index is the interval number." INDEX { ifIndex, xdsl2PMLHist1DUnit, xdsl2PMLHist1DInterval } ::= { xdsl2PMLineHist1DayTable 1 } Xdsl2PMLineHist1DayEntry ::= SEQUENCE { xdsl2PMLHist1DUnit Xdsl2Unit, xdsl2PMLHist1DInterval Gauge, xdsl2PMLHist1DMonitoredTime Gauge, xdsl2PMLHist1DFecs Counter, xdsl2PMLHist1DEs Counter, xdsl2PMLHist1DSes Counter, xdsl2PMLHist1DLoss Counter, xdsl2PMLHist1DUas Counter, xdsl2PMLHist1DValidInterval TruthValue } xdsl2PMLHist1DUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2PMLineHist1DayEntry 1 } xdsl2PMLHist1DInterval OBJECT-TYPE SYNTAX Gauge(1..30) ACCESS not-accessible STATUS mandatory DESCRIPTION "The interval number." ::= { xdsl2PMLineHist1DayEntry 2 } xdsl2PMLHist1DMonitoredTime OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total seconds monitored in this interval." ::= { xdsl2PMLineHist1DayEntry 3 } xdsl2PMLHist1DFecs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.1 (FECS-L) and paragraph #7.2.1.2.1 (FECS-LFE)" ::= { xdsl2PMLineHist1DayEntry 4 } xdsl2PMLHist1DEs OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.2 (ES-L) and paragraph #7.2.1.2.2 (ES-LFE)" ::= { xdsl2PMLineHist1DayEntry 5 } xdsl2PMLHist1DSes OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or more of the received bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.3 (SES-L) and paragraph #7.2.1.2.3 (SES-LFE)" ::= { xdsl2PMLineHist1DayEntry 6 } xdsl2PMLHist1DLoss OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R)." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.4 (LOSS-L) and paragraph #7.2.1.2.4 (LOSS-LFE)" ::= { xdsl2PMLineHist1DayEntry 7 } xdsl2PMLHist1DUas OBJECT-TYPE SYNTAX Counter -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored seconds." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.1.5 (UAS-L) and paragraph #7.2.1.2.5 (UAS-LFE)" ::= { xdsl2PMLineHist1DayEntry 8 } xdsl2PMLHist1DValidInterval OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { xdsl2PMLineHist1DayEntry 9 } xdsl2PMLineInitHist15MinTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMLineInitHist15MinEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMLineInitHist15MinTable contains PM line initialization history for 15-minute intervals of DSL line." ::= { xdsl2PMLine 5 } xdsl2PMLineInitHist15MinEntry OBJECT-TYPE SYNTAX Xdsl2PMLineInitHist15MinEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index is the interval number." INDEX { ifIndex, xdsl2PMLInitHist15MInterval } ::= { xdsl2PMLineInitHist15MinTable 1 } Xdsl2PMLineInitHist15MinEntry ::= SEQUENCE { xdsl2PMLInitHist15MInterval Gauge, xdsl2PMLInitHist15MMonitoredTime Gauge, xdsl2PMLInitHist15MFullInits Gauge, xdsl2PMLInitHist15MFailedFullInits Gauge, xdsl2PMLInitHist15MShortInits Gauge, xdsl2PMLInitHist15MFailedShortInits Gauge, xdsl2PMLInitHist15MValidInterval TruthValue } xdsl2PMLInitHist15MInterval OBJECT-TYPE SYNTAX Gauge(1..96) ACCESS not-accessible STATUS mandatory DESCRIPTION "The interval number." ::= { xdsl2PMLineInitHist15MinEntry 1 } xdsl2PMLInitHist15MMonitoredTime OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total seconds monitored in this interval." ::= { xdsl2PMLineInitHist15MinEntry 2 } xdsl2PMLInitHist15MFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of full initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.1" ::= { xdsl2PMLineInitHist15MinEntry 3 } xdsl2PMLInitHist15MFailedFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed full initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.2" ::= { xdsl2PMLineInitHist15MinEntry 4 } xdsl2PMLInitHist15MShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of short initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.3" ::= { xdsl2PMLineInitHist15MinEntry 5 } xdsl2PMLInitHist15MFailedShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed short initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.4" ::= { xdsl2PMLineInitHist15MinEntry 6 } xdsl2PMLInitHist15MValidInterval OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { xdsl2PMLineInitHist15MinEntry 7 } xdsl2PMLineInitHist1DayTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMLineInitHist1DayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMLineInitHist1DayTable contains PM line initialization history for 24-hour intervals for DSL lines." ::= { xdsl2PMLine 6 } xdsl2PMLineInitHist1DayEntry OBJECT-TYPE SYNTAX Xdsl2PMLineInitHist1DayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of vdsl2(251). A second index is the interval number." INDEX { ifIndex, xdsl2PMLInitHist1DInterval } ::= { xdsl2PMLineInitHist1DayTable 1 } Xdsl2PMLineInitHist1DayEntry ::= SEQUENCE { xdsl2PMLInitHist1DInterval Gauge, xdsl2PMLInitHist1DMonitoredTime Gauge, xdsl2PMLInitHist1DFullInits Gauge, xdsl2PMLInitHist1DFailedFullInits Gauge, xdsl2PMLInitHist1DShortInits Gauge, xdsl2PMLInitHist1DFailedShortInits Gauge, xdsl2PMLInitHist1DValidInterval TruthValue } xdsl2PMLInitHist1DInterval OBJECT-TYPE SYNTAX Gauge(1..30) ACCESS not-accessible STATUS mandatory DESCRIPTION "The interval number." ::= { xdsl2PMLineInitHist1DayEntry 1 } xdsl2PMLInitHist1DMonitoredTime OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total seconds monitored in this interval." ::= { xdsl2PMLineInitHist1DayEntry 2 } xdsl2PMLInitHist1DFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of full initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.1" ::= { xdsl2PMLineInitHist1DayEntry 3 } xdsl2PMLInitHist1DFailedFullInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed full initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.2" ::= { xdsl2PMLineInitHist1DayEntry 4 } xdsl2PMLInitHist1DShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of short initializations attempted on the line (successful and failed) during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.3" ::= { xdsl2PMLineInitHist1DayEntry 5 } xdsl2PMLInitHist1DFailedShortInits OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of failed short initializations on the line during this interval." REFERENCE "ITU-T G.997.1, paragraph #7.2.1.3.4" ::= { xdsl2PMLineInitHist1DayEntry 6 } xdsl2PMLInitHist1DValidInterval OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { xdsl2PMLineInitHist1DayEntry 7 } xdsl2PMChCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMChCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMChCurrTable contains current Performance Monitoring results for DSL channels." ::= { xdsl2PMChannel 1 } xdsl2PMChCurrEntry OBJECT-TYPE SYNTAX Xdsl2PMChCurrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the termination unit." INDEX { ifIndex, xdsl2PMChCurrUnit } ::= { xdsl2PMChCurrTable 1 } Xdsl2PMChCurrEntry ::= SEQUENCE { xdsl2PMChCurrUnit Xdsl2Unit, xdsl2PMChCurr15MValidIntervals Gauge, xdsl2PMChCurr15MInvalidIntervals Gauge, xdsl2PMChCurr15MTimeElapsed HCPerfTimeElapsed, xdsl2PMChCurr15MCodingViolations Gauge, xdsl2PMChCurr15MCorrectedBlocks Gauge, xdsl2PMChCurr1DayValidIntervals Gauge, xdsl2PMChCurr1DayInvalidIntervals Gauge, xdsl2PMChCurr1DayTimeElapsed HCPerfTimeElapsed, xdsl2PMChCurr1DayCodingViolations Gauge, xdsl2PMChCurr1DayCorrectedBlocks Gauge } xdsl2PMChCurrUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2PMChCurrEntry 1 } xdsl2PMChCurr15MValidIntervals OBJECT-TYPE SYNTAX Gauge(0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implementation is planned to store (i.e., beyond the scope of this MIB module) unless the measurement was (re-)started recently, in which case the value will be the number of complete 15-minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy), it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { xdsl2PMChCurrEntry 2 } xdsl2PMChCurr15MInvalidIntervals OBJECT-TYPE SYNTAX Gauge(0..96) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { xdsl2PMChCurrEntry 3 } xdsl2PMChCurr15MTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed -- Rsyntax INTEGER(0..86399) -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total elapsed seconds in this interval." ::= { xdsl2PMChCurrEntry 4 } xdsl2PMChCurr15MCodingViolations OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.1 (CV-C) and paragraph #7.2.2.2.1 (CV-CFE)" ::= { xdsl2PMChCurrEntry 5 } xdsl2PMChCurr15MCorrectedBlocks OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.2 (FEC-C) and paragraph #7.2.2.2.2 (FEC-CFE)" ::= { xdsl2PMChCurrEntry 6 } xdsl2PMChCurr1DayValidIntervals OBJECT-TYPE SYNTAX Gauge(0..30) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementation is planned to store (i.e., beyond the scope of this MIB module) unless the measurement was (re-)started recently, in which case the value will be the number of complete 24-hour intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy), it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available." ::= { xdsl2PMChCurrEntry 7 } xdsl2PMChCurr1DayInvalidIntervals OBJECT-TYPE SYNTAX Gauge(0..30) ACCESS read-only STATUS mandatory DESCRIPTION "The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations)." ::= { xdsl2PMChCurrEntry 8 } xdsl2PMChCurr1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed -- Rsyntax INTEGER(0..86399) -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total elapsed seconds in this interval." ::= { xdsl2PMChCurrEntry 9 } xdsl2PMChCurr1DayCodingViolations OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.1 (CV-C) and paragraph #7.2.2.2.1 (CV-CFE)" ::= { xdsl2PMChCurrEntry 10 } xdsl2PMChCurr1DayCorrectedBlocks OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.2 (FEC-C) and paragraph #7.2.2.2.2 (FEC-CFE)" ::= { xdsl2PMChCurrEntry 11 } xdsl2PMChHist15MinTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMChHist15MinEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMChHist15MinTable contains Performance Monitoring (PM) history for 15-minute intervals for DSL channels PM." ::= { xdsl2PMChannel 2 } xdsl2PMChHist15MinEntry OBJECT-TYPE SYNTAX Xdsl2PMChHist15MinEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the transmission unit. The third index is the interval number." INDEX { ifIndex, xdsl2PMChHist15MUnit, xdsl2PMChHist15MInterval } ::= { xdsl2PMChHist15MinTable 1 } Xdsl2PMChHist15MinEntry ::= SEQUENCE { xdsl2PMChHist15MUnit Xdsl2Unit, xdsl2PMChHist15MInterval Gauge, xdsl2PMChHist15MMonitoredTime Gauge, xdsl2PMChHist15MCodingViolations Gauge, xdsl2PMChHist15MCorrectedBlocks Gauge, xdsl2PMChHist15MValidInterval TruthValue } xdsl2PMChHist15MUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2PMChHist15MinEntry 1 } xdsl2PMChHist15MInterval OBJECT-TYPE SYNTAX Gauge(1..96) ACCESS not-accessible STATUS mandatory DESCRIPTION "The interval number." ::= { xdsl2PMChHist15MinEntry 2 } xdsl2PMChHist15MMonitoredTime OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total seconds monitored in this interval." ::= { xdsl2PMChHist15MinEntry 3 } xdsl2PMChHist15MCodingViolations OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.1 (CV-C) and paragraph #7.2.2.2.1 (CV-CFE)" ::= { xdsl2PMChHist15MinEntry 4 } xdsl2PMChHist15MCorrectedBlocks OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.2 (FEC-C) and paragraph #7.2.2.2.2 (FEC-CFE)" ::= { xdsl2PMChHist15MinEntry 5 } xdsl2PMChHist15MValidInterval OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { xdsl2PMChHist15MinEntry 6 } xdsl2PMChHist1DTable OBJECT-TYPE SYNTAX SEQUENCE OF Xdsl2PMChHist1DEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table xdsl2PMChHist1DTable contains Performance Monitoring (PM) history for 1-day intervals for DSL channels PM." ::= { xdsl2PMChannel 3 } xdsl2PMChHist1DEntry OBJECT-TYPE SYNTAX Xdsl2PMChHist1DEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "One index of this table is an interface index where the interface has an ifType of a DSL channel. A second index of this table is the transmission unit. The third index is the interval number." INDEX { ifIndex, xdsl2PMChHist1DUnit, xdsl2PMChHist1DInterval } ::= { xdsl2PMChHist1DTable 1 } Xdsl2PMChHist1DEntry ::= SEQUENCE { xdsl2PMChHist1DUnit Xdsl2Unit, xdsl2PMChHist1DInterval Gauge, xdsl2PMChHist1DMonitoredTime Gauge, xdsl2PMChHist1DCodingViolations Gauge, xdsl2PMChHist1DCorrectedBlocks Gauge, xdsl2PMChHist1DValidInterval TruthValue } xdsl2PMChHist1DUnit OBJECT-TYPE SYNTAX Xdsl2Unit -- Rsyntax INTEGER { -- xtuc(1), -- xtur(2) -- } ACCESS not-accessible STATUS mandatory DESCRIPTION "The termination unit." ::= { xdsl2PMChHist1DEntry 1 } xdsl2PMChHist1DInterval OBJECT-TYPE SYNTAX Gauge(1..30) ACCESS not-accessible STATUS mandatory DESCRIPTION "The interval number." ::= { xdsl2PMChHist1DEntry 2 } xdsl2PMChHist1DMonitoredTime OBJECT-TYPE SYNTAX Gauge -- Units -- seconds ACCESS read-only STATUS mandatory DESCRIPTION "Total seconds monitored in this interval." ::= { xdsl2PMChHist1DEntry 3 } xdsl2PMChHist1DCodingViolations OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.1 (CV-C) and paragraph #7.2.2.2.1 (CV-CFE)" ::= { xdsl2PMChHist1DEntry 4 } xdsl2PMChHist1DCorrectedBlocks OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly SHOULD increment each of the counters related to the individual channels." REFERENCE "ITU-T G.997.1, paragraph #7.2.2.1.2 (FEC-C) and paragraph #7.2.2.2.2 (FEC-CFE)" ::= { xdsl2PMChHist1DEntry 5 } xdsl2PMChHist1DValidInterval OBJECT-TYPE SYNTAX TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } ACCESS read-only STATUS mandatory DESCRIPTION "This variable indicates if the data for this interval is valid." ::= { xdsl2PMChHist1DEntry 6 } xdsl2LinePerfFECSThreshXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MFecs, xdsl2LineAlarmConfProfileXtucThresh15MinFecs } -- Status -- mandatory DESCRIPTION "This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred xTU-C." ::= 1 xdsl2LinePerfFECSThreshXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MFecs, xdsl2LineAlarmConfProfileXturThresh15MinFecs } -- Status -- mandatory DESCRIPTION "This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred xTU-R." ::= 2 xdsl2LinePerfESThreshXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MEs, xdsl2LineAlarmConfProfileXtucThresh15MinEs } -- Status -- mandatory DESCRIPTION "This notification indicates that the errored seconds threshold has been reached/exceeded for the referred xTU-C." ::= 3 xdsl2LinePerfESThreshXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MEs, xdsl2LineAlarmConfProfileXturThresh15MinEs } -- Status -- mandatory DESCRIPTION "This notification indicates that the errored seconds threshold has been reached/exceeded for the referred xTU-R." ::= 4 xdsl2LinePerfSESThreshXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MSes, xdsl2LineAlarmConfProfileXtucThresh15MinSes } -- Status -- mandatory DESCRIPTION "This notification indicates that the severely errored seconds threshold has been reached/exceeded for the referred xTU-C." ::= 5 xdsl2LinePerfSESThreshXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MSes, xdsl2LineAlarmConfProfileXturThresh15MinSes } -- Status -- mandatory DESCRIPTION "This notification indicates that the severely errored seconds threshold has been reached/exceeded for the referred xTU-R." ::= 6 xdsl2LinePerfLOSSThreshXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MLoss, xdsl2LineAlarmConfProfileXtucThresh15MinLoss } -- Status -- mandatory DESCRIPTION "This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred xTU-C." ::= 7 xdsl2LinePerfLOSSThreshXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MLoss, xdsl2LineAlarmConfProfileXturThresh15MinLoss } -- Status -- mandatory DESCRIPTION "This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred xTU-R." ::= 8 xdsl2LinePerfUASThreshXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MUas, xdsl2LineAlarmConfProfileXtucThresh15MinUas } -- Status -- mandatory DESCRIPTION "This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred xTU-C." ::= 9 xdsl2LinePerfUASThreshXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLCurr15MUas, xdsl2LineAlarmConfProfileXturThresh15MinUas } -- Status -- mandatory DESCRIPTION "This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred xTU-R." ::= 10 xdsl2LinePerfCodingViolationsThreshXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMChCurr15MCodingViolations, xdsl2ChAlarmConfProfileXtucThresh15MinCodingViolations } -- Status -- mandatory DESCRIPTION "This notification indicates that the coding violations threshold has been reached/exceeded for the referred xTU-C." ::= 11 xdsl2LinePerfCodingViolationsThreshXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMChCurr15MCodingViolations, xdsl2ChAlarmConfProfileXturThresh15MinCodingViolations } -- Status -- mandatory DESCRIPTION "This notification indicates that the coding violations threshold has been reached/exceeded for the referred xTU-R." ::= 12 xdsl2LinePerfCorrectedThreshXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMChCurr15MCorrectedBlocks, xdsl2ChAlarmConfProfileXtucThresh15MinCorrected } -- Status -- mandatory DESCRIPTION "This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred xTU-C." ::= 13 xdsl2LinePerfCorrectedThreshXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMChCurr15MCorrectedBlocks, xdsl2ChAlarmConfProfileXturThresh15MinCorrected } -- Status -- mandatory DESCRIPTION "This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred xTU-R." ::= 14 xdsl2LinePerfFailedFullInitThresh TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLInitCurr15MFailedFullInits, xdsl2LineAlarmConfProfileThresh15MinFailedFullInt } -- Status -- mandatory DESCRIPTION "This notification indicates that the failed full initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line." ::= 15 xdsl2LinePerfFailedShortInitThresh TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2PMLInitCurr15MFailedShortInits, xdsl2LineAlarmConfProfileThresh15MinFailedShrtInt } -- Status -- mandatory DESCRIPTION "This notification indicates that the failed short initializations threshold has been reached/exceeded for the referred VDSL2/ADSL/ADSL2 or ADSL2+ line." ::= 16 xdsl2LineStatusChangeXtuc TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2LineStatusXtuc } -- Status -- mandatory DESCRIPTION "This notification indicates that a status change is detected for the referred xTU-C." ::= 17 xdsl2LineStatusChangeXtur TRAP-TYPE -- Reverse mappable trap ENTERPRISE vdsl2MIB VARIABLES { xdsl2LineStatusXtur } -- Status -- mandatory DESCRIPTION "This notification indicates that a status change is detected for the referred xTU-R." ::= 18 xdsl2LineGroup OBJECT IDENTIFIER ::= { xdsl2Groups 1 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of configuration, status, and commands objects -- on the line level. -- objects -- xdsl2LineConfTemplate, xdsl2LineAlarmConfTemplate, -- xdsl2LineCmndConfPmsf, xdsl2LineCmndConfLdsf, -- xdsl2LineCmndConfLdsfFailReason, -- xdsl2LineCmndAutomodeColdStart, xdsl2LineCmndConfReset, -- xdsl2LineStatusXtuTransSys, xdsl2LineStatusPwrMngState, -- xdsl2LineStatusInitResult, xdsl2LineStatusLastStateDs, -- xdsl2LineStatusLastStateUs, xdsl2LineStatusXtur, -- xdsl2LineStatusXtuc, xdsl2LineStatusAttainableRateDs, -- xdsl2LineStatusAttainableRateUs, xdsl2LineStatusActPsdDs, -- xdsl2LineStatusActPsdUs, xdsl2LineStatusActAtpDs, -- xdsl2LineStatusActAtpUs, xdsl2LineStatusActProfile, -- xdsl2LineStatusActLimitMask, xdsl2LineStatusActUs0Mask, -- xdsl2LineStatusActSnrModeDs, xdsl2LineStatusActSnrModeUs, -- xdsl2LineStatusElectricalLength, xdsl2LineStatusTssiDs, -- xdsl2LineStatusTssiUs, xdsl2LineStatusMrefPsdDs, -- xdsl2LineStatusMrefPsdUs, xdsl2LineStatusTrellisDs, -- xdsl2LineStatusTrellisUs, xdsl2LineStatusActualCe, -- xdsl2LineBandStatusLnAtten, xdsl2LineBandStatusSigAtten, -- xdsl2LineBandStatusSnrMargin xdsl2LineFallbackGroup OBJECT IDENTIFIER ::= { xdsl2Groups 2 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of configuration, status, and commands -- objects on the line level that are associated with the -- fallback feature. -- objects -- xdsl2LineConfFallbackTemplate, xdsl2LineStatusActTemplate xdsl2LineBpscGroup OBJECT IDENTIFIER ::= { xdsl2Groups 3 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of configuration, status, and commands -- objects on the line level that are associated with requesting -- a bits-per-subcarrier measurement. -- objects -- xdsl2LineCmndConfBpsc, xdsl2LineCmndConfBpscFailReason, -- xdsl2LineCmndConfBpscRequests xdsl2LineSegmentGroup OBJECT IDENTIFIER ::= { xdsl2Groups 4 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of status and commands objects on the line -- level that are used to hold the results of the -- bits-per-subcarrier measurement. -- objects -- xdsl2LineSegmentBitsAlloc, xdsl2LineSegmentRowStatus xdsl2ChannelStatusGroup OBJECT IDENTIFIER ::= { xdsl2Groups 5 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of status objects on the channel level. -- objects -- xdsl2ChStatusActDataRate, xdsl2ChStatusPrevDataRate, -- xdsl2ChStatusActDelay, xdsl2ChStatusActInp, -- xdsl2ChStatusInpReport, xdsl2ChStatusNFec, xdsl2ChStatusRFec, -- xdsl2ChStatusLSymb, xdsl2ChStatusIntlvDepth, -- xdsl2ChStatusIntlvBlock, xdsl2ChStatusLPath xdsl2ChannelStatusAtmGroup OBJECT IDENTIFIER ::= { xdsl2Groups 6 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of status objects on the data path level -- when it is ATM. -- objects -- xdsl2ChStatusAtmStatus xdsl2ChannelStatusPtmGroup OBJECT IDENTIFIER ::= { xdsl2Groups 7 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of status objects on the data path level -- when it is PTM. -- objects -- xdsl2ChStatusPtmStatus xdsl2SCStatusGroup OBJECT IDENTIFIER ::= { xdsl2Groups 8 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of status objects on the subcarrier level. -- They are updated as a result of a DELT process. -- objects -- xdsl2SCStatusLinScale, xdsl2SCStatusLinScGroupSize, -- xdsl2SCStatusLogMt, xdsl2SCStatusLogScGroupSize, -- xdsl2SCStatusQlnMt, xdsl2SCStatusQlnScGroupSize, -- xdsl2SCStatusSnrMtime, xdsl2SCStatusSnrScGroupSize, -- xdsl2SCStatusBandLnAtten, xdsl2SCStatusBandSigAtten, -- xdsl2SCStatusAttainableRate, xdsl2SCStatusRowStatus, -- xdsl2SCStatusSegmentLinReal, xdsl2SCStatusSegmentLinImg, -- xdsl2SCStatusSegmentLog, xdsl2SCStatusSegmentQln, -- xdsl2SCStatusSegmentSnr, xdsl2SCStatusSegmentBitsAlloc, -- xdsl2SCStatusSegmentGainAlloc xdsl2LineInventoryGroup OBJECT IDENTIFIER ::= { xdsl2Groups 9 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of inventory objects per xTU. -- objects -- xdsl2LInvG994VendorId, xdsl2LInvSystemVendorId, -- xdsl2LInvVersionNumber, xdsl2LInvSerialNumber, -- xdsl2LInvSelfTestResult, xdsl2LInvTransmissionCapabilities xdsl2LineConfTemplateGroup OBJECT IDENTIFIER ::= { xdsl2Groups 10 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a line configuration -- -- template. -- objects -- xdsl2LConfTempLineProfile, xdsl2LConfTempChan1ConfProfile, -- xdsl2LConfTempChan1RaRatioDs, xdsl2LConfTempChan1RaRatioUs, -- xdsl2LConfTempChan2ConfProfile, xdsl2LConfTempChan2RaRatioDs, -- xdsl2LConfTempChan2RaRatioUs, xdsl2LConfTempChan3ConfProfile, -- xdsl2LConfTempChan3RaRatioDs, xdsl2LConfTempChan3RaRatioUs, -- xdsl2LConfTempChan4ConfProfile, xdsl2LConfTempChan4RaRatioDs, -- xdsl2LConfTempChan4RaRatioUs, xdsl2LConfTempRowStatus xdsl2LineConfProfGroup OBJECT IDENTIFIER ::= { xdsl2Groups 11 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a line configuration -- profile. -- objects -- xdsl2LConfProfScMaskDs, xdsl2LConfProfScMaskUs, -- xdsl2LConfProfVdsl2CarMask, xdsl2LConfProfRfiBands, -- xdsl2LConfProfRaModeDs, xdsl2LConfProfRaModeUs, -- xdsl2LConfProfTargetSnrmDs, xdsl2LConfProfTargetSnrmUs, -- xdsl2LConfProfMaxSnrmDs, xdsl2LConfProfMaxSnrmUs, -- xdsl2LConfProfMinSnrmDs, xdsl2LConfProfMinSnrmUs, -- xdsl2LConfProfCeFlag, xdsl2LConfProfSnrModeDs, -- xdsl2LConfProfSnrModeUs, xdsl2LConfProfTxRefVnDs, -- xdsl2LConfProfTxRefVnUs, xdsl2LConfProfXtuTransSysEna, -- xdsl2LConfProfPmMode, xdsl2LConfProfL0Time, -- xdsl2LConfProfL2Time, xdsl2LConfProfL2Atpr, -- xdsl2LConfProfL2Atprt, xdsl2LConfProfProfiles, -- xdsl2LConfProfDpboEPsd, xdsl2LConfProfDpboEsEL, -- xdsl2LConfProfDpboEsCableModelA, -- xdsl2LConfProfDpboEsCableModelB, -- xdsl2LConfProfDpboEsCableModelC, xdsl2LConfProfDpboMus, -- xdsl2LConfProfDpboFMin, xdsl2LConfProfDpboFMax, -- xdsl2LConfProfUpboKL, xdsl2LConfProfUpboKLF, -- xdsl2LConfProfUs0Mask, xdsl2LConfProfForceInp, -- xdsl2LConfProfRowStatus xdsl2LineConfProfRaGroup OBJECT IDENTIFIER ::= { xdsl2Groups 12 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects required for controlling the -- rate-adaptive behavior of the line. -- objects -- xdsl2LConfProfRaUsNrmDs, xdsl2LConfProfRaUsNrmUs, -- xdsl2LConfProfRaUsTimeDs, xdsl2LConfProfRaUsTimeUs, -- xdsl2LConfProfRaDsNrmDs, xdsl2LConfProfRaDsNrmUs, -- xdsl2LConfProfRaDsTimeDs, xdsl2LConfProfRaDsTimeUs xdsl2LineConfProfMsgMinGroup OBJECT IDENTIFIER ::= { xdsl2Groups 13 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects required for controlling the rate -- reserved for Overhead traffic. -- objects -- xdsl2LConfProfMsgMinUs, xdsl2LConfProfMsgMinDs xdsl2LineConfProfModeSpecGroup OBJECT IDENTIFIER ::= { xdsl2Groups 14 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a line configuration profile -- that have an instance for each operation mode allowed. -- objects -- xdsl2LConfProfMaxNomPsdDs, xdsl2LConfProfMaxNomPsdUs, -- xdsl2LConfProfMaxNomAtpDs, xdsl2LConfProfMaxNomAtpUs, -- xdsl2LConfProfMaxAggRxPwrUs, xdsl2LConfProfPsdMaskDs, -- xdsl2LConfProfPsdMaskUs, xdsl2LConfProfPsdMaskSelectUs, -- xdsl2LConfProfClassMask, xdsl2LConfProfLimitMask, -- xdsl2LConfProfUs0Disable, xdsl2LConfProfModeSpecRowStatus xdsl2LineConfProfModeSpecBandUsGroup OBJECT IDENTIFIER ::= { xdsl2Groups 15 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a line configuration profile -- that have several per-upstream-band instances for each -- operation mode allowed. -- objects -- xdsl2LConfProfUpboPsdA, xdsl2LConfProfUpboPsdB, -- xdsl2LConfProfModeSpecBandUsRowStatus xdsl2ChConfProfileGroup OBJECT IDENTIFIER ::= { xdsl2Groups 16 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a channel configuration -- profile. -- objects -- xdsl2ChConfProfMinDataRateDs, xdsl2ChConfProfMinDataRateUs, -- xdsl2ChConfProfMaxDataRateDs, xdsl2ChConfProfMaxDataRateUs, -- xdsl2ChConfProfMinDataRateLowPwrDs, -- xdsl2ChConfProfMinDataRateLowPwrUs, xdsl2ChConfProfMaxDelayDs, -- xdsl2ChConfProfMaxDelayUs, xdsl2ChConfProfMinProtectionDs, -- xdsl2ChConfProfMinProtectionUs, -- xdsl2ChConfProfMinProtection8Ds, -- xdsl2ChConfProfMinProtection8Us, xdsl2ChConfProfMaxBerDs, -- xdsl2ChConfProfMaxBerUs, xdsl2ChConfProfUsDataRateDs, -- xdsl2ChConfProfDsDataRateDs, xdsl2ChConfProfUsDataRateUs, -- xdsl2ChConfProfDsDataRateUs, xdsl2ChConfProfRowStatus xdsl2ChConfProfileAtmGroup OBJECT IDENTIFIER ::= { xdsl2Groups 17 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of configuration objects required when the data -- path is ATM. -- objects -- xdsl2ChConfProfImaEnabled, xdsl2ChStatusAtmStatus xdsl2ChConfProfileMinResGroup OBJECT IDENTIFIER ::= { xdsl2Groups 18 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of configuration objects required for the -- reserved data rate. -- objects -- xdsl2ChConfProfMinResDataRateDs, -- xdsl2ChConfProfMinResDataRateUs xdsl2ChConfProfileOptAttrGroup OBJECT IDENTIFIER ::= { xdsl2Groups 19 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of various optional channel configuration -- parameters. -- objects -- xdsl2ChConfProfMaxDelayVar, xdsl2ChConfProfInitPolicy xdsl2LineAlarmConfTemplateGroup OBJECT IDENTIFIER ::= { xdsl2Groups 20 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a line alarm template. -- objects -- xdsl2LAlarmConfTempLineProfile, -- xdsl2LAlarmConfTempChan1ConfProfile, -- xdsl2LAlarmConfTempChan2ConfProfile, -- xdsl2LAlarmConfTempChan3ConfProfile, -- xdsl2LAlarmConfTempChan4ConfProfile, -- xdsl2LAlarmConfTempRowStatus xdsl2LineAlarmConfProfileGroup OBJECT IDENTIFIER ::= { xdsl2Groups 21 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a line alarm profile. -- objects -- xdsl2LineAlarmConfProfileXtucThresh15MinFecs, -- xdsl2LineAlarmConfProfileXtucThresh15MinEs, -- xdsl2LineAlarmConfProfileXtucThresh15MinSes, -- xdsl2LineAlarmConfProfileXtucThresh15MinLoss, -- xdsl2LineAlarmConfProfileXtucThresh15MinUas, -- xdsl2LineAlarmConfProfileXturThresh15MinFecs, -- xdsl2LineAlarmConfProfileXturThresh15MinEs, -- xdsl2LineAlarmConfProfileXturThresh15MinSes, -- xdsl2LineAlarmConfProfileXturThresh15MinLoss, -- xdsl2LineAlarmConfProfileXturThresh15MinUas, -- xdsl2LineAlarmConfProfileThresh15MinFailedFullInt, -- xdsl2LineAlarmConfProfileThresh15MinFailedShrtInt, -- xdsl2LineAlarmConfProfileRowStatus xdsl2ChAlarmConfProfileGroup OBJECT IDENTIFIER ::= { xdsl2Groups 22 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects in a channel alarm profile. -- objects -- xdsl2ChAlarmConfProfileXtucThresh15MinCodingViolations, -- xdsl2ChAlarmConfProfileXtucThresh15MinCorrected, -- xdsl2ChAlarmConfProfileXturThresh15MinCodingViolations, -- xdsl2ChAlarmConfProfileXturThresh15MinCorrected, -- xdsl2ChAlarmConfProfileRowStatus xdsl2PMLineCurrGroup OBJECT IDENTIFIER ::= { xdsl2Groups 23 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects that report the line-level -- counters for current PM intervals. -- objects -- xdsl2PMLCurr15MValidIntervals, -- xdsl2PMLCurr15MInvalidIntervals, xdsl2PMLCurr15MTimeElapsed, -- xdsl2PMLCurr15MFecs, xdsl2PMLCurr15MEs, xdsl2PMLCurr15MSes, -- xdsl2PMLCurr15MLoss, xdsl2PMLCurr15MUas, -- xdsl2PMLCurr1DayValidIntervals, -- xdsl2PMLCurr1DayInvalidIntervals, xdsl2PMLCurr1DayTimeElapsed, -- xdsl2PMLCurr1DayFecs, xdsl2PMLCurr1DayEs, xdsl2PMLCurr1DaySes, -- xdsl2PMLCurr1DayLoss, xdsl2PMLCurr1DayUas xdsl2PMLineInitCurrGroup OBJECT IDENTIFIER ::= { xdsl2Groups 24 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects that report the full -- initialization counters for current PM intervals. -- objects -- xdsl2PMLInitCurr15MValidIntervals, -- xdsl2PMLInitCurr15MInvalidIntervals, -- xdsl2PMLInitCurr15MTimeElapsed, xdsl2PMLInitCurr15MFullInits, -- xdsl2PMLInitCurr15MFailedFullInits, -- xdsl2PMLInitCurr1DayValidIntervals, -- xdsl2PMLInitCurr1DayInvalidIntervals, -- xdsl2PMLInitCurr1DayTimeElapsed, -- xdsl2PMLInitCurr1DayFullInits, -- xdsl2PMLInitCurr1DayFailedFullInits xdsl2PMLineInitCurrShortGroup OBJECT IDENTIFIER ::= { xdsl2Groups 25 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects that report the short -- initialization counters for current PM intervals. -- objects -- xdsl2PMLInitCurr15MShortInits, -- xdsl2PMLInitCurr15MFailedShortInits, -- xdsl2PMLInitCurr1DayShortInits, -- xdsl2PMLInitCurr1DayFailedShortInits xdsl2PMLineHist15MinGroup OBJECT IDENTIFIER ::= { xdsl2Groups 26 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of line-level PM counters for the previous -- 15-minute intervals. -- objects -- xdsl2PMLHist15MMonitoredTime, xdsl2PMLHist15MFecs, -- xdsl2PMLHist15MEs, xdsl2PMLHist15MSes, xdsl2PMLHist15MLoss, -- xdsl2PMLHist15MUas, xdsl2PMLHist15MValidInterval xdsl2PMLineHist1DayGroup OBJECT IDENTIFIER ::= { xdsl2Groups 27 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of line-level PM counters for the previous -- 24-hour intervals. -- objects -- xdsl2PMLHist1DMonitoredTime, xdsl2PMLHist1DFecs, -- xdsl2PMLHist1DEs, xdsl2PMLHist1DSes, xdsl2PMLHist1DLoss, -- xdsl2PMLHist1DUas, xdsl2PMLHist1DValidInterval xdsl2PMLineInitHist15MinGroup OBJECT IDENTIFIER ::= { xdsl2Groups 28 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of PM counters for the previous 15-minute -- interval full initializations. -- objects -- xdsl2PMLInitHist15MMonitoredTime, -- xdsl2PMLInitHist15MFullInits, -- xdsl2PMLInitHist15MFailedFullInits, -- xdsl2PMLInitHist15MValidInterval xdsl2PMLineInitHist15MinShortGroup OBJECT IDENTIFIER ::= { xdsl2Groups 29 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of PM counters for the previous 15-minute -- interval short initializations. -- objects -- xdsl2PMLInitHist15MShortInits, -- xdsl2PMLInitHist15MFailedShortInits xdsl2PMLineInitHist1DayGroup OBJECT IDENTIFIER ::= { xdsl2Groups 30 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of PM counters for the previous 24-hour -- interval full initializations. -- objects -- xdsl2PMLInitHist1DMonitoredTime, xdsl2PMLInitHist1DFullInits, -- xdsl2PMLInitHist1DFailedFullInits, -- xdsl2PMLInitHist1DValidInterval xdsl2PMLineInitHist1DayShortGroup OBJECT IDENTIFIER ::= { xdsl2Groups 31 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of PM counters for the previous 24-hour -- interval short initializations. -- objects -- xdsl2PMLInitHist1DShortInits, -- xdsl2PMLInitHist1DFailedShortInits xdsl2PMChCurrGroup OBJECT IDENTIFIER ::= { xdsl2Groups 32 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects that report the channel-level -- counters for current PM intervals. -- objects -- xdsl2PMChCurr15MValidIntervals, -- xdsl2PMChCurr15MInvalidIntervals, xdsl2PMChCurr15MTimeElapsed, -- xdsl2PMChCurr15MCodingViolations, -- xdsl2PMChCurr15MCorrectedBlocks, -- xdsl2PMChCurr1DayValidIntervals, -- xdsl2PMChCurr1DayInvalidIntervals, -- xdsl2PMChCurr1DayTimeElapsed, -- xdsl2PMChCurr1DayCodingViolations, -- xdsl2PMChCurr1DayCorrectedBlocks xdsl2PMChHist15MinGroup OBJECT IDENTIFIER ::= { xdsl2Groups 33 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects that report the channel-level -- counters for previous 15-minute PM intervals. -- objects -- xdsl2PMChHist15MMonitoredTime, -- xdsl2PMChHist15MCodingViolations, -- xdsl2PMChHist15MCorrectedBlocks, -- xdsl2PMChHist15MValidInterval xdsl2PMChHist1DGroup OBJECT IDENTIFIER ::= { xdsl2Groups 34 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects that report the channel-level -- counters for previous 24-hour PM intervals. -- objects -- xdsl2PMChHist1DMonitoredTime, xdsl2PMChHist1DCodingViolations, -- xdsl2PMChHist1DCorrectedBlocks, xdsl2PMChHist1DValidInterval xdsl2ScalarSCGroup OBJECT IDENTIFIER ::= { xdsl2Groups 35 } -- OBJECT-GROUP -- Status -- mandatory -- Descr -- The group of objects that report the available memory -- resources for DELT processes. -- objects -- xdsl2ScalarSCMaxInterfaces, xdsl2ScalarSCAvailInterfaces xdsl2ThreshNotificationGroup OBJECT IDENTIFIER ::= { xdsl2Groups 36 } -- NOTIFICATION-GROUP -- Status -- mandatory -- Descr -- This group supports notifications of significant -- conditions associated with DSL lines. -- notifications -- xdsl2LinePerfFECSThreshXtuc, xdsl2LinePerfFECSThreshXtur, -- xdsl2LinePerfESThreshXtuc, xdsl2LinePerfESThreshXtur, -- xdsl2LinePerfSESThreshXtuc, xdsl2LinePerfSESThreshXtur, -- xdsl2LinePerfLOSSThreshXtuc, xdsl2LinePerfLOSSThreshXtur, -- xdsl2LinePerfUASThreshXtuc, xdsl2LinePerfUASThreshXtur, -- xdsl2LinePerfCodingViolationsThreshXtuc, -- xdsl2LinePerfCodingViolationsThreshXtur, -- xdsl2LinePerfCorrectedThreshXtuc, -- xdsl2LinePerfCorrectedThreshXtur, -- xdsl2LinePerfFailedFullInitThresh, -- xdsl2LinePerfFailedShortInitThresh xdsl2StatusChangeNotificationGroup OBJECT IDENTIFIER ::= { xdsl2Groups 37 } -- NOTIFICATION-GROUP -- Status -- mandatory -- Descr -- This group supports notifications of thresholds crossing -- associated with DSL lines. -- notifications -- xdsl2LineStatusChangeXtuc, xdsl2LineStatusChangeXtur xdsl2LineMibCompliance OBJECT IDENTIFIER ::= { xdsl2Compliances 1 } -- MODULE-COMPLIANCE -- Status -- mandatory -- Descr -- The compliance statement for SNMP entities which -- manage VDSL2/ADSL/ADSL2 and ADSL2+ interfaces. -- Module -- >>current<< -- MandGroup -- xdsl2LineGroup -- MandGroup -- xdsl2ChannelStatusGroup -- MandGroup -- xdsl2SCStatusGroup -- MandGroup -- xdsl2LineInventoryGroup -- MandGroup -- xdsl2LineConfTemplateGroup -- MandGroup -- xdsl2LineConfProfGroup -- MandGroup -- xdsl2LineConfProfModeSpecGroup -- MandGroup -- xdsl2LineConfProfModeSpecBandUsGroup -- MandGroup -- xdsl2ChConfProfileGroup -- MandGroup -- xdsl2LineAlarmConfTemplateGroup -- MandGroup -- xdsl2PMLineCurrGroup -- MandGroup -- xdsl2PMLineInitCurrGroup -- MandGroup -- xdsl2PMLineHist15MinGroup -- MandGroup -- xdsl2PMLineHist1DayGroup -- MandGroup -- xdsl2PMLineInitHist15MinGroup -- MandGroup -- xdsl2PMLineInitHist1DayGroup -- MandGroup -- xdsl2PMChCurrGroup -- MandGroup -- xdsl2PMChHist15MinGroup -- MandGroup -- xdsl2PMChHist1DGroup -- OptGroup -- xdsl2LineFallbackGroup -- OptGroup -- xdsl2LineBpscGroup -- OptGroup -- xdsl2LineSegmentGroup -- OptGroup -- xdsl2ChannelStatusAtmGroup -- OptGroup -- xdsl2ChannelStatusPtmGroup -- OptGroup -- xdsl2LineConfProfRaGroup -- OptGroup -- xdsl2LineConfProfMsgMinGroup -- OptGroup -- xdsl2LineAlarmConfProfileGroup -- OptGroup -- xdsl2ChAlarmConfProfileGroup -- OptGroup -- xdsl2ChConfProfileAtmGroup -- OptGroup -- xdsl2ChConfProfileMinResGroup -- OptGroup -- xdsl2ChConfProfileOptAttrGroup -- OptGroup -- xdsl2PMLineInitCurrShortGroup -- OptGroup -- xdsl2PMLineInitHist15MinShortGroup -- OptGroup -- xdsl2PMLineInitHist1DayShortGroup -- OptGroup -- xdsl2ScalarSCGroup -- OptGroup -- xdsl2ThreshNotificationGroup -- OptGroup -- xdsl2StatusChangeNotificationGroup END