-- *****************************************************************
-- CISCO-BGP4-MIB.my
--   
-- June 2001, Ravindra Rathi
--   
-- Copyright (c) 2001, 2010, 2020 by Cisco Systems Inc.
-- All rights reserved.
--   
-- *****************************************************************

CISCO-BGP4-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    NOTIFICATION-TYPE,
    Integer32,
    Unsigned32,
    Gauge32,
    Counter32,
    IpAddress
        FROM SNMPv2-SMI
    MODULE-COMPLIANCE,
    OBJECT-GROUP,
    NOTIFICATION-GROUP
        FROM SNMPv2-CONF
    TruthValue,
    TEXTUAL-CONVENTION
        FROM SNMPv2-TC
    InetAddressType,
    InetAddress,
    InetPortNumber,
    InetAutonomousSystemNumber
        FROM INET-ADDRESS-MIB
    SnmpAdminString
        FROM SNMP-FRAMEWORK-MIB
    bgpPeerEntry,
    bgpPeerRemoteAddr,
    bgpPeerLastError,
    bgpPeerState
        FROM BGP4-MIB
    ciscoMgmt
        FROM CISCO-SMI;


ciscoBgp4MIB MODULE-IDENTITY
    LAST-UPDATED    "202005080000Z"
    ORGANIZATION    "Cisco Systems, Inc."
    CONTACT-INFO
            "Cisco Systems
            Customer Service

            Postal: 170 W Tasman Drive
            San Jose, CA  95134
            USA

            Tel: +1 800 553-NETS

            E-mail: cs-iprouting-bgp@cisco.com"
    DESCRIPTION
        "An extension to the IETF BGP4 MIB module defined in
        RFC 1657.

        Following is the terminology associated with Border
        Gateway Protocol(BGP).

        UPDATE message
            UPDATE messages are used to transfer routing 
            information between BGP peers. An UPDATE message 
            is used to advertise a single feasible route to a
            peer, or to withdraw multiple unfeasible routes 
            from service.                 

        Adj-RIBs-In 
           The Adj-RIBs-In store routing information that has
           been learned from inbound UPDATE messages. Their 
           contents represent routes that are available as an 
           input to the Decision Process.

        Loc-RIB(BGP table) 
           The Loc-RIB contains the local routing information
           that the BGP speaker has selected by applying its 
           local policies to the routing information contained 
           in its Adj-RIBs-In.

        Adj-RIBs-Out 
           The Adj-RIBs-Out store the information that the
           local BGP speaker has selected for advertisement to 
           its peers. The routing information stored in the 
           Adj-RIBs-Out will be carried in the local BGP 
           speaker's UPDATE messages and advertised to its
           peers.

        Path Attributes
           A variable length sequence of path attributes is 
           present in every UPDATE. Each path attribute is a 
           triple <attribute type, attribute length, 
           attribute value> of variable length. 

        Network Layer Reachability Information(NLRI)
           A variable length field present in UPDATE messages
           which contains a list of Network Layer address 
           prefixes. 

        Address Family Identifier(AFI) 
           Primary identifier to indicate the type of the 
           Network Layer Reachability Information(NLRI) being 
           carried.

        Subsequent Address Family Identifier(SAFI) 
           Secondary identifier to indicate the type of the 
           Network Layer Reachability Information(NLRI) being 
           carried."
    REVISION        "202005060000Z"
    DESCRIPTION
        "+cbgpPeer3Table: Changed VrfId, Type, RemoteAddr, VrfName to read-only"
    REVISION        "202004140000Z"
    DESCRIPTION
        "+Added cbgpPeer3Table"
    REVISION        "201009300000Z"
    DESCRIPTION
        "+Added cbgpNotifsEnable and cbgpLocalAs
        +Modified CbgpNetworkAddress TC
        +Added cbgpPeer2Table
        +Added cbgpPeer2CapsTable
        +Added cbgpPeer2AddrFamilyTable
        +Added cbgpPeer2AddrFamilyPrefixTable
        +Added notification cbgpPeer2EstablishedNotification
        +Added notification cbgpPeer2BackwardTransNotification
        +Added notification cbgpPeer2FsmStateChange
        +Added notification cbgpPeer2BackwardTransition
        +Added notification cbgpPeer2PrefixThresholdExceeded
        +Added notification cbgpPeer2PrefixThresholdClear"
    REVISION        "200302240000Z"
    DESCRIPTION
        "+Added cbgpPeerCapsTable
        +Added cbgpPeerAddrFamilyTable
        +Added cbgpPeerAddrFamilyPrefixTable
        +Added notification event cbgpBackwardTransition
        +Added notification event cbgpPrefixThresholdExceeded
        +Added notification event cbgpPrefixThresholdClear"
    REVISION        "200212190000Z"
    DESCRIPTION
        "+Added cbgpPeerPrefixTable
        +Added notification event cbgpFsmStateChange"
    REVISION        "200108130000Z"
    DESCRIPTION
        "Initial version of the MIB module."
    ::= { ciscoMgmt 187 }


ciscoBgp4MIBObjects  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIB 1 }

cbgpRoute  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIBObjects 1 }

cbgpPeer  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIBObjects 2 }

cbgpGlobal  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIBObjects 3 }


-- Textual convention

CbgpSafi ::= TEXTUAL-CONVENTION
    STATUS          current
    DESCRIPTION
        "Subsequent Address Family Identifier(SAFI) is used
        by BGP speaker to indicate the type of the the Network
        Layer Reachability Information(NLRI) being carried. 
        RFC-2858 has defined the following values for SAFI.
        1 - Network Layer Reachability Information used for 
            unicast forwarding
        2 - Network Layer Reachability Information used for 
            multicast forwarding
        3 - Network Layer Reachability Information used for 
            both unicast and multicast forwarding. 
        SAFI values 128 through 255 are for private use."

    REFERENCE
        "RFC-2858: Multiprotocol Extensions for BGP-4,
         RFC-2547: BGP/MPLS VPNs"
    SYNTAX          INTEGER  {
                        unicast(1),
                        multicast(2),
                        unicastAndMulticast(3),
                        vpn(128)
                    }

CbgpNetworkAddress ::= TEXTUAL-CONVENTION
    STATUS          current
    DESCRIPTION
        "Represents the Network Address prefix carried in the
        BGP UPDATE messages.  In the following table, column 
        'Type' gives the kind of Network Layer address which 
        will be stored in the object of this type based on the
        values of Address Family Identifier(AFI) and SAFI.

         AFI          SAFI                   Type

        ipv4(1)      unicast(1)            IPv4 address 
        ipv4(1)      multicast(2)          IPv4 address
        ipv4(1)      vpn(128)              VPN-IPv4 address
        ipv6(2)      unicast(1)            IPv6 address
        ipv6(2)      multicast(2)          IPv6 address
        ipv6(2)      vpn(128)              VPN-IPv6 address

        A VPN-IPv4 address is a 12-byte quantity, beginning 
        with an 8-byte 'Route Distinguisher (RD)' and ending 
        with a 4-byte IPv4 address.

        A VPN-IPv6 address is a 24-byte quantity, beginning 
        with an 8-byte 'Route Distinguisher (RD)' and ending 
        with a 16-byte IPv6 address."

    REFERENCE
        "RFC 2858, Multiprotocol Extensions for BGP-4.
         RFC 2547, Section 4.1, BGP/MPLS VPNs."
    SYNTAX          OCTET STRING (SIZE (0..255))

-- Global objects.

cbgpNotifsEnable OBJECT-TYPE
    SYNTAX          BITS {
                        notifsEnable(0),
                        notifsPeer2Enable(1)
                    }
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Indicates whether the specific notifications are
        enabled. 
        If notifsEnable(0) bit is set to 1,
        then the notifications defined in
        ciscoBgp4NotificationsGroup1 are enabled; 
        If notifsPeer2Enable(1) bit is set to 1,
        then the notifications defined in
        ciscoBgp4Peer2NotificationsGroup are enabled." 
    ::= { cbgpGlobal 1 }

cbgpLocalAs OBJECT-TYPE
    SYNTAX          InetAutonomousSystemNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The local autonomous system (AS) number."
    REFERENCE
        "RFC 4271, Section 4.2, 'My Autonomous System'.
         RFC 4893, BGP Support for Four-octet AS
         Number Space." 
    ::= { cbgpGlobal 2 }
-- BGP4 Received Routes for all the supported address families

cbgpRouteTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpRouteEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table contains information about routes to
        destination networks from all BGP4 peers.  Since 
        BGP4 can carry routes for multiple Network Layer 
        protocols, this table has the Address Family 
        Identifier(AFI) of the Network Layer protocol as the 
        first index. Further for a given AFI, routes carried
        by BGP4 are distinguished based on Subsequent Address 
        Family Identifiers(SAFI).  Hence that is used as the
        second index.  Conceptually there is a separate Loc-RIB
        maintained by the BGP speaker for each combination of 
        AFI and SAFI supported by it."
    REFERENCE
        "RFC-1771: A Border Gateway Protocol 4 (BGP-4),
         RFC-2858: Multiprotocol Extensions for BGP-4,
         RFC-2547: BGP/MPLS VPNs"
    ::= { cbgpRoute 1 }

cbgpRouteEntry OBJECT-TYPE
    SYNTAX          CbgpRouteEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Information about a path to a network received from
        a peer."
    INDEX           {
                        cbgpRouteAfi,
                        cbgpRouteSafi,
                        cbgpRoutePeerType,
                        cbgpRoutePeer,
                        cbgpRouteAddrPrefix,
                        cbgpRouteAddrPrefixLen
                    } 
    ::= { cbgpRouteTable 1 }

CbgpRouteEntry ::= SEQUENCE {
        cbgpRouteAfi                InetAddressType,
        cbgpRouteSafi               CbgpSafi,
        cbgpRoutePeerType           InetAddressType,
        cbgpRoutePeer               InetAddress,
        cbgpRouteAddrPrefix         CbgpNetworkAddress,
        cbgpRouteAddrPrefixLen      Unsigned32,
        cbgpRouteOrigin             INTEGER,
        cbgpRouteASPathSegment      OCTET STRING,
        cbgpRouteNextHop            CbgpNetworkAddress,
        cbgpRouteMedPresent         TruthValue,
        cbgpRouteMultiExitDisc      Unsigned32,
        cbgpRouteLocalPrefPresent   TruthValue,
        cbgpRouteLocalPref          Unsigned32,
        cbgpRouteAtomicAggregate    INTEGER,
        cbgpRouteAggregatorAS       Unsigned32,
        cbgpRouteAggregatorAddrType InetAddressType,
        cbgpRouteAggregatorAddr     InetAddress,
        cbgpRouteBest               TruthValue,
        cbgpRouteUnknownAttr        OCTET STRING
}

cbgpRouteAfi OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Represents Address Family Identifier(AFI) of the
        Network Layer protocol associated with the route.
        An implementation is only required to support IPv4
        unicast and VPNv4 (Value - 1) address families." 
    ::= { cbgpRouteEntry 1 }

cbgpRouteSafi OBJECT-TYPE
    SYNTAX          CbgpSafi
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Represents Subsequent Address Family Identifier(SAFI)
        of the route. It gives additional information about
        the type of the route. An implementation is only 
        required to support IPv4 unicast(Value - 1) and VPNv4(
        Value - 128) address families." 
    ::= { cbgpRouteEntry 2 }

cbgpRoutePeerType OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Represents the type of Network Layer address stored
        in cbgpRoutePeer. An implementation is only required
        to support IPv4 address type(Value - 1)." 
    ::= { cbgpRouteEntry 3 }

cbgpRoutePeer OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The Network Layer address of the peer where the route
        information was learned. An implementation is only 
        required to support an IPv4 peer." 
    ::= { cbgpRouteEntry 4 }

cbgpRouteAddrPrefix OBJECT-TYPE
    SYNTAX          CbgpNetworkAddress
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "A Network Address prefix in the Network Layer
        Reachability Information field of BGP UPDATE message.
        This object is a Network Address containing the prefix
        with length specified by cbgpRouteAddrPrefixLen. Any
        bits beyond the length specified by
        cbgpRouteAddrPrefixLen are zeroed." 
    ::= { cbgpRouteEntry 5 }

cbgpRouteAddrPrefixLen OBJECT-TYPE
    SYNTAX          Unsigned32 (0..2040)
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Length in bits of the Network Address prefix in the
        Network Layer Reachability Information field." 
    ::= { cbgpRouteEntry 6 }

cbgpRouteOrigin OBJECT-TYPE
    SYNTAX          INTEGER  {
                        igp(1), -- networks are interior
                        egp(2), -- networks learned via EGP
                        incomplete(3) -- undetermined                        
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The ultimate origin of the route information." 
    ::= { cbgpRouteEntry 7 }

cbgpRouteASPathSegment OBJECT-TYPE
    SYNTAX          OCTET STRING (SIZE  (0..255))
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The sequence of AS path segments.  Each AS
        path segment is represented by a triple
        <type, length, value>.

        The type is a 1-octet field which has two
        possible values:
        1  AS_SET: unordered set of ASs a route in the 
                  UPDATE message has traversed
        2  AS_SEQUENCE: ordered set of ASs a route in the
                       UPDATE message has traversed.

        The length is a 1-octet field containing the
        number of ASs in the value field.

        The value field contains one or more AS
        numbers, each AS is represented in the octet
        string as a pair of octets according to the
        following algorithm:

        first-byte-of-pair = ASNumber / 256;
        second-byte-of-pair = ASNumber & 255;" 
    ::= { cbgpRouteEntry 8 }

cbgpRouteNextHop OBJECT-TYPE
    SYNTAX          CbgpNetworkAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The Network Layer address of the border router
        that should be used for the destination network." 
    ::= { cbgpRouteEntry 9 }

cbgpRouteMedPresent OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Indicates the presence/absence of MULTI_EXIT_DISC
        attribute for the route." 
    ::= { cbgpRouteEntry 10 }

cbgpRouteMultiExitDisc OBJECT-TYPE
    SYNTAX          Unsigned32 (0..4294967295)
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This metric is used to discriminate between multiple
        exit points to an adjacent autonomous system.  The
        value of this object is irrelevant if the value of
        of cbgpRouteMedPresent is false(2)." 
    ::= { cbgpRouteEntry 11 }

cbgpRouteLocalPrefPresent OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Indicates the presence/absence of LOCAL_PREF
        attribute for the route." 
    ::= { cbgpRouteEntry 12 }

cbgpRouteLocalPref OBJECT-TYPE
    SYNTAX          Unsigned32 (0..4294967295)
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The degree of preference calculated by the local BGP4
        speaker for the route. The value of this object is 
        irrelevant if the value of cbgpRouteLocalPrefPresent 
        is false(2)." 
    ::= { cbgpRouteEntry 13 }

cbgpRouteAtomicAggregate OBJECT-TYPE
    SYNTAX          INTEGER  {
                        lessSpecificRouteNotSelected(1),
                        lessSpecificRouteSelected(2)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Whether or not the local system has selected a less
        specific route without selecting a more specific
        route." 
    ::= { cbgpRouteEntry 14 }

cbgpRouteAggregatorAS OBJECT-TYPE
    SYNTAX          Unsigned32 (0..65535)
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The AS number of the last BGP4 speaker that performed
        route aggregation.  A value of zero (0) indicates the 
        absence of this attribute." 
    ::= { cbgpRouteEntry 15 }

cbgpRouteAggregatorAddrType OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Represents the type of Network Layer address stored
        in cbgpRouteAggregatorAddr." 
    ::= { cbgpRouteEntry 16 }

cbgpRouteAggregatorAddr OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The Network Layer address of the last BGP4 speaker
        that performed route aggregation.  A value of all zeros
        indicates the absence of this attribute." 
    ::= { cbgpRouteEntry 17 }

cbgpRouteBest OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "An indication of whether or not this route was chosen
        as the best BGP4 route." 
    ::= { cbgpRouteEntry 18 }

cbgpRouteUnknownAttr OBJECT-TYPE
    SYNTAX          OCTET STRING (SIZE  (0..255))
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "One or more path attributes not understood by this
        BGP4 speaker.  Size zero (0) indicates the absence of
        such attribute(s).  Octets beyond the maximum size, if
        any, are not recorded by this object.  

        Each path attribute is a triple <attribute type,
        attribute length, attribute value> of variable length.
        Attribute Type is a two-octet field that consists of
        the Attribute Flags octet followed by the Attribute
        Type Code octet.  If the Extended Length bit of the 
        Attribute Flags octet is set to 0, the third octet of 
        the Path Attribute contains the length of the
        attribute data in octets.  If the Extended Length bit 
        of the Attribute Flags octet is set to 1, then the
        third and the fourth octets of the path attribute 
        contain the length of the attribute data in octets.
        The remaining octets of the Path Attribute represent 
        the attribute value and are interpreted according to 
        the Attribute Flags and the Attribute Type Code."
    REFERENCE
        "RFC-1771: A Border Gateway Protocol 4 (BGP-4), 
        section 4.3" 
    ::= { cbgpRouteEntry 19 }
 

-- BGP Peer table.

cbgpPeerTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeerEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "BGP peer table.  This table contains,
        one entry per BGP peer, information about
        the connections with BGP peers."
    ::= { cbgpPeer 1 }

cbgpPeerEntry OBJECT-TYPE
    SYNTAX          CbgpPeerEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Entry containing information about the
        connection with a BGP peer."
    AUGMENTS           { bgpPeerEntry  } 
    ::= { cbgpPeerTable 1 }

CbgpPeerEntry ::= SEQUENCE {
        cbgpPeerPrefixAccepted   Counter32,
        cbgpPeerPrefixDenied     Counter32,
        cbgpPeerPrefixLimit      Unsigned32,
        cbgpPeerPrefixAdvertised Counter32,
        cbgpPeerPrefixSuppressed Counter32,
        cbgpPeerPrefixWithdrawn  Counter32,
        cbgpPeerLastErrorTxt     SnmpAdminString,
        cbgpPeerPrevState        INTEGER
}

cbgpPeerPrefixAccepted OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          deprecated
    DESCRIPTION
        "Number of Route prefixes received on this connnection,
        which are accepted after applying filters. Possible
        filters are route maps, prefix lists, distributed
        lists, etc." 
    ::= { cbgpPeerEntry 1 }

cbgpPeerPrefixDenied OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          deprecated
    DESCRIPTION
        "Counter which gets incremented when a route prefix
        received on this connection is denied  or when a route
        prefix is denied during soft reset of this connection
        if 'soft-reconfiguration' is on . This object is 
        initialized to zero when the peer is  configured or
        the router is rebooted" 
    ::= { cbgpPeerEntry 2 }

cbgpPeerPrefixLimit OBJECT-TYPE
    SYNTAX          Unsigned32 (1..4294967295)
    MAX-ACCESS      read-write
    STATUS          deprecated
    DESCRIPTION
        "Max number of route prefixes accepted on this
        connection" 
    ::= { cbgpPeerEntry 3 }

cbgpPeerPrefixAdvertised OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          deprecated
    DESCRIPTION
        "Counter which gets incremented when a route prefix
        is advertised on this connection. This object is
        initialized to zero when the peer is configured or 
        the router is rebooted" 
    ::= { cbgpPeerEntry 4 }

cbgpPeerPrefixSuppressed OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          deprecated
    DESCRIPTION
        "Counter which gets incremented when a route prefix
        is suppressed from being sent on this connection. This 
        object is initialized to zero when the peer is 
        configured or the router is rebooted" 
    ::= { cbgpPeerEntry 5 }

cbgpPeerPrefixWithdrawn OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          deprecated
    DESCRIPTION
        "Counter which gets incremented when a route prefix
        is withdrawn on this connection. This object is
        initialized to zero when the peer is configured or
        the router is rebooted" 
    ::= { cbgpPeerEntry 6 }

cbgpPeerLastErrorTxt OBJECT-TYPE
    SYNTAX          SnmpAdminString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Implementation specific error description for
        bgpPeerLastErrorReceived." 
    ::= { cbgpPeerEntry 7 }

cbgpPeerPrevState OBJECT-TYPE
    SYNTAX          INTEGER  {
                        none(0),
                        idle(1),
                        connect(2),
                        active(3),
                        opensent(4),
                        openconfirm(5),
                        established(6)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP peer connection previous state."
    REFERENCE
        "Section 8, RFC 1771, A Border Gateway Protocol 4 
         (BGP-4)." 
    ::= { cbgpPeerEntry 8 }
 

-- Peer capabilities

cbgpPeerCapsTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeerCapsEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table contains the capabilities that are
        supported by a peer. Capabilities of a peer are 
        received during BGP connection establishment.
        Values corresponding to each received capability
        are stored in this table. When a new capability 
        is received, this table is updated with a new 
        entry. When an existing capability is not received 
        during the latest connection establishment, the 
        corresponding entry is deleted from the table."
    REFERENCE
        "RFC 2842, Capabilities Advertisement with
         BGP-4.

         RFC2818, Route Refresh Capability for BGP-4.

         RFC2858, Multiprotocol Extensions for BGP-4.

         draft-ietf-idr-restart-05.txt, Graceful Restart
         Mechanism for BGP"
    ::= { cbgpPeer 2 }

cbgpPeerCapsEntry OBJECT-TYPE
    SYNTAX          CbgpPeerCapsEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Each entry represents a capability received from a
        peer with a particular code and an index. When a 
        capability is received multiple times with different
        values during a BGP connection establishment, 
        corresponding entries are differentiated with indices."
    INDEX           {
                        bgpPeerRemoteAddr,
                        cbgpPeerCapCode,
                        cbgpPeerCapIndex
                    } 
    ::= { cbgpPeerCapsTable 1 }

CbgpPeerCapsEntry ::= SEQUENCE {
        cbgpPeerCapCode  INTEGER,
        cbgpPeerCapIndex Unsigned32,
        cbgpPeerCapValue OCTET STRING
}

cbgpPeerCapCode OBJECT-TYPE
    SYNTAX          INTEGER  {
                        multiProtocol(1),
                        routeRefresh(2),
                        gracefulRestart(64),
                        routeRefreshOld(128)
                    }
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The BGP Capability Advertisement Capability Code."
    REFERENCE
        "RFC 2842, Capabilities Advertisement with
         BGP-4.

         RFC2818, Route Refresh Capability for BGP-4.

         RFC2858, Multiprotocol Extensions for BGP-4.

         draft-ietf-idr-restart-05.txt, Graceful Restart
         Mechanism for BGP" 
    ::= { cbgpPeerCapsEntry 1 }

cbgpPeerCapIndex OBJECT-TYPE
    SYNTAX          Unsigned32 (1..128)
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Multiple instances of a given capability may be
        sent by a BGP speaker.  This variable is used
        to index them." 
    ::= { cbgpPeerCapsEntry 2 }

cbgpPeerCapValue OBJECT-TYPE
    SYNTAX          OCTET STRING (SIZE  (0..255))
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The value of the announced capability. This
        MIB object value is organized as given below,
            Capability : Route Refresh Capability
                         Null string
            Capability : Multiprotocol Extensions
              +----------------------------------+
              | AFI(16 bits)                     |
              +----------------------------------+
              | SAFI (8 bits)                    |
              +----------------------------------+
            Capability : Graceful Restart
              +----------------------------------+
              | Restart Flags (4 bits)           |
              +----------------------------------+
              | Restart Time in seconds (12 bits)|
              +----------------------------------+
              | AFI(16 bits)                     |
              +----------------------------------+
              | SAFI (8 bits)                    |
              +----------------------------------+
              | Flags for Address Family (8 bits)|
              +----------------------------------+
              | ...                              |
              +----------------------------------+
              | AFI(16 bits)                     |
              +----------------------------------+
              | SAFI (8 bits)                    |
              +----------------------------------+
              | Flags for Address Family (8 bits)|
              +----------------------------------+"
    REFERENCE
        "RFC 2842, Capabilities Advertisement with
         BGP-4.

         RFC2818, Route Refresh Capability for BGP-4.

         RFC2858, Multiprotocol Extensions for BGP-4.

         draft-ietf-idr-restart-05.txt, Graceful Restart
         Mechanism for BGP" 
    ::= { cbgpPeerCapsEntry 3 }
 

-- BGP Peer Address Family table

cbgpPeerAddrFamilyTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeerAddrFamilyEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table contains information related to
        address families supported by a peer. Supported
        address families of a peer are known during BGP 
        connection establishment. When a new supported 
        address family is known, this table is updated 
        with a new entry. When an address family is not 
        supported any more, corresponding entry is deleted 
        from the table."
    ::= { cbgpPeer 3 }

cbgpPeerAddrFamilyEntry OBJECT-TYPE
    SYNTAX          CbgpPeerAddrFamilyEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is identified by an AFI/SAFI pair and
        peer address. It contains names associated with
        an address family."
    INDEX           {
                        bgpPeerRemoteAddr,
                        cbgpPeerAddrFamilyAfi,
                        cbgpPeerAddrFamilySafi
                    } 
    ::= { cbgpPeerAddrFamilyTable 1 }

CbgpPeerAddrFamilyEntry ::= SEQUENCE {
        cbgpPeerAddrFamilyAfi  InetAddressType,
        cbgpPeerAddrFamilySafi CbgpSafi,
        cbgpPeerAddrFamilyName SnmpAdminString
}

cbgpPeerAddrFamilyAfi OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The AFI index of the entry. An implementation
        is only required to support IPv4 unicast and 
        VPNv4 (Value - 1) address families." 
    ::= { cbgpPeerAddrFamilyEntry 1 }

cbgpPeerAddrFamilySafi OBJECT-TYPE
    SYNTAX          CbgpSafi
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The SAFI index of the entry. An implementation
        is only required to support IPv4 unicast(Value 
        - 1) and VPNv4( Value - 128) address families."
    REFERENCE
        "RFC-2858: Multiprotocol Extensions for BGP-4,
         RFC-2547: BGP/MPLS VPNs" 
    ::= { cbgpPeerAddrFamilyEntry 2 }

cbgpPeerAddrFamilyName OBJECT-TYPE
    SYNTAX          SnmpAdminString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Implementation specific Address Family name." 
    ::= { cbgpPeerAddrFamilyEntry 3 }
 

-- BGP Address Family Peer Prefix table

cbgpPeerAddrFamilyPrefixTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeerAddrFamilyPrefixEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table contains prefix related information
        related to address families supported by a peer. 
        Supported address families of a peer are known 
        during BGP connection establishment. When a new 
        supported address family is known, this table 
        is updated with a new entry. When an address 
        family is not supported any more, corresponding 
        entry is deleted from the table."
    ::= { cbgpPeer 4 }

cbgpPeerAddrFamilyPrefixEntry OBJECT-TYPE
    SYNTAX          CbgpPeerAddrFamilyPrefixEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is identified by an AFI/SAFI pair and
        peer address. It contains information associated 
        with route prefixes belonging to an address family."
    INDEX           {
                        bgpPeerRemoteAddr,
                        cbgpPeerAddrFamilyAfi,
                        cbgpPeerAddrFamilySafi
                    } 
    ::= { cbgpPeerAddrFamilyPrefixTable 1 }

CbgpPeerAddrFamilyPrefixEntry ::= SEQUENCE {
        cbgpPeerAcceptedPrefixes     Counter32,
        cbgpPeerDeniedPrefixes       Gauge32,
        cbgpPeerPrefixAdminLimit     Unsigned32,
        cbgpPeerPrefixThreshold      Unsigned32,
        cbgpPeerPrefixClearThreshold Unsigned32,
        cbgpPeerAdvertisedPrefixes   Gauge32,
        cbgpPeerSuppressedPrefixes   Gauge32,
        cbgpPeerWithdrawnPrefixes    Gauge32
}

cbgpPeerAcceptedPrefixes OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of accepted route prefixes on this connection,
        which belong to an address family." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 1 }

cbgpPeerDeniedPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix, which
        belongs to an address family, received on this 
        connection is denied. It is initialized to zero when 
        the connection is undergone a hard reset." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 2 }

cbgpPeerPrefixAdminLimit OBJECT-TYPE
    SYNTAX          Unsigned32 (1..4294967295)
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Max number of route prefixes accepted for an address
        family on this connection." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 3 }

cbgpPeerPrefixThreshold OBJECT-TYPE
    SYNTAX          Unsigned32 (1..100)
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Prefix threshold value (%) for an address family
        on this connection at which warning message stating
        the prefix count is crossed the threshold or 
        corresponding SNMP notification is generated." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 4 }

cbgpPeerPrefixClearThreshold OBJECT-TYPE
    SYNTAX          Unsigned32 (1..100)
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Prefix threshold value (%) for an address family
        on this connection at which SNMP clear notification
        is generated if prefix threshold notification is
        already generated." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 5 }

cbgpPeerAdvertisedPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix,
        which belongs to an address family is advertised
        on this connection. It is initialized to zero when 
        the connection is undergone a hard reset." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 6 }

cbgpPeerSuppressedPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix,
        which belongs to an address family is suppressed
        from being sent on this connection. It is 
        initialized to zero when the connection is undergone
        a hard reset." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 7 }

cbgpPeerWithdrawnPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix,
        which belongs to an address family, is withdrawn on
        this connection. It is initialized to zero when the
        connection is undergone a hard reset." 
    ::= { cbgpPeerAddrFamilyPrefixEntry 8 }
 


cbgpPeer2Table OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeer2Entry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "BGP peer table.  This table contains,
        one entry per BGP peer, information about
        the connections with BGP peers."
    ::= { cbgpPeer 5 }

cbgpPeer2Entry OBJECT-TYPE
    SYNTAX          CbgpPeer2Entry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Entry containing information about the
        connection with a BGP peer."
    INDEX           {
                        cbgpPeer2Type,
                        cbgpPeer2RemoteAddr
                    } 
    ::= { cbgpPeer2Table 1 }

CbgpPeer2Entry ::= SEQUENCE {
        cbgpPeer2Type                          InetAddressType,
        cbgpPeer2RemoteAddr                    InetAddress,
        cbgpPeer2State                         INTEGER,
        cbgpPeer2AdminStatus                   INTEGER,
        cbgpPeer2NegotiatedVersion             Integer32,
        cbgpPeer2LocalAddr                     InetAddress,
        cbgpPeer2LocalPort                     InetPortNumber,
        cbgpPeer2LocalAs                       InetAutonomousSystemNumber,
        cbgpPeer2LocalIdentifier               IpAddress,
        cbgpPeer2RemotePort                    InetPortNumber,
        cbgpPeer2RemoteAs                      InetAutonomousSystemNumber,
        cbgpPeer2RemoteIdentifier              IpAddress,
        cbgpPeer2InUpdates                     Counter32,
        cbgpPeer2OutUpdates                    Counter32,
        cbgpPeer2InTotalMessages               Counter32,
        cbgpPeer2OutTotalMessages              Counter32,
        cbgpPeer2LastError                     OCTET STRING,
        cbgpPeer2FsmEstablishedTransitions     Counter32,
        cbgpPeer2FsmEstablishedTime            Gauge32,
        cbgpPeer2ConnectRetryInterval          Integer32,
        cbgpPeer2HoldTime                      Integer32,
        cbgpPeer2KeepAlive                     Integer32,
        cbgpPeer2HoldTimeConfigured            Integer32,
        cbgpPeer2KeepAliveConfigured           Integer32,
        cbgpPeer2MinASOriginationInterval      Integer32,
        cbgpPeer2MinRouteAdvertisementInterval Integer32,
        cbgpPeer2InUpdateElapsedTime           Gauge32,
        cbgpPeer2LastErrorTxt                  SnmpAdminString,
        cbgpPeer2PrevState                     INTEGER
}

cbgpPeer2Type OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Represents the type of Peer address stored
        in cbgpPeer2Entry." 
    ::= { cbgpPeer2Entry 1 }

cbgpPeer2RemoteAddr OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The remote IP address of this entry's BGP
        peer." 
    ::= { cbgpPeer2Entry 2 }

cbgpPeer2State OBJECT-TYPE
    SYNTAX          INTEGER  {
                        idle(1),
                        connect(2),
                        active(3),
                        opensent(4),
                        openconfirm(5),
                        established(6)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP peer connection state."
    REFERENCE       "RFC 4271, Section 8.2.2." 
    ::= { cbgpPeer2Entry 3 }

cbgpPeer2AdminStatus OBJECT-TYPE
    SYNTAX          INTEGER  {
                        stop(1),
                        start(2)
                    }
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The desired state of the BGP connection.
        A transition from 'stop' to 'start' will cause
        the BGP Manual Start Event to be generated.
        A transition from 'start' to 'stop' will cause
        the BGP Manual Stop Event to be generated.
        This parameter can be used to restart BGP peer
        connections.  Care should be used in providing
        write access to this object without adequate
        authentication."
    REFERENCE       "RFC 4271, Section 8.1.2." 
    ::= { cbgpPeer2Entry 4 }

cbgpPeer2NegotiatedVersion OBJECT-TYPE
    SYNTAX          Integer32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The negotiated version of BGP running between
        the two peers.

        This entry MUST be zero (0) unless the
        cbgpPeer2State is in the openconfirm or the
        established state.

        Note that legal values for this object are
        between 0 and 255."
    REFERENCE
        "RFC 4271, Section 4.2.
         RFC 4271, Section 7." 
    ::= { cbgpPeer2Entry 5 }

cbgpPeer2LocalAddr OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The local IP address of this entry's BGP
        connection." 
    ::= { cbgpPeer2Entry 6 }

cbgpPeer2LocalPort OBJECT-TYPE
    SYNTAX          InetPortNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The local port for the TCP connection between
        the BGP peers." 
    ::= { cbgpPeer2Entry 7 }

cbgpPeer2LocalAs OBJECT-TYPE
    SYNTAX          InetAutonomousSystemNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The local AS number for this session." 
    ::= { cbgpPeer2Entry 8 }

cbgpPeer2LocalIdentifier OBJECT-TYPE
    SYNTAX          IpAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP Identifier of this entry's BGP peer." 
    ::= { cbgpPeer2Entry 9 }

cbgpPeer2RemotePort OBJECT-TYPE
    SYNTAX          InetPortNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The remote port for the TCP connection
        between the BGP peers.  Note that the
        objects cbgpPeer2LocalAddr,
        cbgpPeer2LocalPort, cbgpPeer2RemoteAddr, and
        cbgpPeer2RemotePort provide the appropriate
        reference to the standard MIB TCP
        connection table." 
    ::= { cbgpPeer2Entry 10 }

cbgpPeer2RemoteAs OBJECT-TYPE
    SYNTAX          InetAutonomousSystemNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The remote autonomous system number received in
        the BGP OPEN message."
    REFERENCE       "RFC 4271, Section 4.2." 
    ::= { cbgpPeer2Entry 11 }

cbgpPeer2RemoteIdentifier OBJECT-TYPE
    SYNTAX          IpAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP Identifier of this entry's BGP peer.
        This entry MUST be 0.0.0.0 unless the
        cbgpPeer2State is in the openconfirm or the
        established state."
    REFERENCE       "RFC 4271, Section 4.2, 'BGP Identifier'." 
    ::= { cbgpPeer2Entry 12 }

cbgpPeer2InUpdates OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The number of BGP UPDATE messages
        received on this connection."
    REFERENCE       "RFC 4271, Section 4.3." 
    ::= { cbgpPeer2Entry 13 }

cbgpPeer2OutUpdates OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The number of BGP UPDATE messages
        transmitted on this connection."
    REFERENCE       "RFC 4271, Section 4.3." 
    ::= { cbgpPeer2Entry 14 }

cbgpPeer2InTotalMessages OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The total number of messages received
        from the remote peer on this connection."
    REFERENCE       "RFC 4271, Section 4." 
    ::= { cbgpPeer2Entry 15 }

cbgpPeer2OutTotalMessages OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The total number of messages transmitted to
        the remote peer on this connection."
    REFERENCE       "RFC 4271, Section 4." 
    ::= { cbgpPeer2Entry 16 }

cbgpPeer2LastError OBJECT-TYPE
    SYNTAX          OCTET STRING (SIZE  (2))
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The last error code and subcode seen by this
        peer on this connection.  If no error has
        occurred, this field is zero.  Otherwise, the
        first byte of this two byte OCTET STRING
        contains the error code, and the second byte
        contains the subcode."
    REFERENCE       "RFC 4271, Section 4.5." 
    ::= { cbgpPeer2Entry 17 }

cbgpPeer2FsmEstablishedTransitions OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The total number of times the BGP FSM
        transitioned into the established state
        for this peer."
    REFERENCE       "RFC 4271, Section 8." 
    ::= { cbgpPeer2Entry 18 }

cbgpPeer2FsmEstablishedTime OBJECT-TYPE
    SYNTAX          Gauge32
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This timer indicates how long (in
        seconds) this peer has been in the
        established state or how long
        since this peer was last in the
        established state.  It is set to zero when
        a new peer is configured or when the router is
        booted."
    REFERENCE       "RFC 4271, Section 8." 
    ::= { cbgpPeer2Entry 19 }

cbgpPeer2ConnectRetryInterval OBJECT-TYPE
    SYNTAX          Integer32 (1..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        ConnectRetry timer.  The suggested value
        for this timer is 120 seconds."
    REFERENCE
        "RFC 4271, Section 8.2.2.  This is the value used
         to initialize the 'ConnectRetryTimer'." 
    ::= { cbgpPeer2Entry 20 }

cbgpPeer2HoldTime OBJECT-TYPE
    SYNTAX          Integer32 (0 | 3..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the Hold
        Timer established with the peer.  The
        value of this object is calculated by this
        BGP speaker, using the smaller of the
        values in cbgpPeer2HoldTimeConfigured and the
        Hold Time received in the OPEN message.

        This value must be at least three seconds
        if it is not zero (0).

        If the Hold Timer has not been established
        with the peer this object MUST have a value
        of zero (0).

        If the cbgpPeer2HoldTimeConfigured object has
        a value of (0), then this object MUST have a
        value of (0)."
    REFERENCE       "RFC 4271, Section 4.2." 
    ::= { cbgpPeer2Entry 21 }

cbgpPeer2KeepAlive OBJECT-TYPE
    SYNTAX          Integer32 (0 | 1..21845)
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the KeepAlive
        timer established with the peer.  The value
        of this object is calculated by this BGP
        speaker such that, when compared with
        cbgpPeer2HoldTime, it has the same proportion
        that cbgpPeer2KeepAliveConfigured has,
        compared with cbgpPeer2HoldTimeConfigured.

        If the KeepAlive timer has not been established
        with the peer, this object MUST have a value
        of zero (0).

        If the of cbgpPeer2KeepAliveConfigured object
        has a value of (0), then this object MUST have
        a value of (0)."
    REFERENCE       "RFC 4271, Section 4.4." 
    ::= { cbgpPeer2Entry 22 }

cbgpPeer2HoldTimeConfigured OBJECT-TYPE
    SYNTAX          Integer32 (0 | 3..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the Hold Time
        configured for this BGP speaker with this
        peer.  This value is placed in an OPEN
        message sent to this peer by this BGP
        speaker, and is compared with the Hold
        Time field in an OPEN message received
        from the peer when determining the Hold
        Time (cbgpPeer2HoldTime) with the peer.
        This value must not be less than three
        seconds if it is not zero (0).  If it is
        zero (0), the Hold Time is NOT to be
        established with the peer.  The suggested
        value for this timer is 90 seconds."
    REFERENCE
        "RFC 4271, Section 4.2.
         RFC 4271, Section 10." 
    ::= { cbgpPeer2Entry 23 }

cbgpPeer2KeepAliveConfigured OBJECT-TYPE
    SYNTAX          Integer32 (0 | 1..21845)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        KeepAlive timer configured for this BGP
        speaker with this peer.  The value of this
        object will only determine the
        KEEPALIVE messages' frequency relative to
        the value specified in
        cbgpPeer2HoldTimeConfigured; the actual
        time interval for the KEEPALIVE messages is
        indicated by cbgpPeer2KeepAlive.  A
        reasonable maximum value for this timer
        would be one third of that of
        cbgpPeer2HoldTimeConfigured.
        If the value of this object is zero (0),
        no periodical KEEPALIVE messages are sent
        to the peer after the BGP connection has
        been established.  The suggested value for
        this timer is 30 seconds."
    REFERENCE
        "RFC 4271, Section 4.4.
         RFC 4271, Section 10." 
    ::= { cbgpPeer2Entry 24 }

cbgpPeer2MinASOriginationInterval OBJECT-TYPE
    SYNTAX          Integer32 (1..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        MinASOriginationInterval timer.
        The suggested value for this timer is 15
        seconds."
    REFERENCE
        "RFC 4271, Section 9.2.1.2.
         RFC 4271, Section 10." 
    ::= { cbgpPeer2Entry 25 }

cbgpPeer2MinRouteAdvertisementInterval OBJECT-TYPE
    SYNTAX          Integer32 (1..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        MinRouteAdvertisementInterval timer.
        The suggested value for this timer is 30
        seconds for EBGP connections and 5
        seconds for IBGP connections."
    REFERENCE
        "RFC 4271, Section 9.2.1.1.
         RFC 4271, Section 10." 
    ::= { cbgpPeer2Entry 26 }

cbgpPeer2InUpdateElapsedTime OBJECT-TYPE
    SYNTAX          Gauge32
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Elapsed time (in seconds) since the last BGP
        UPDATE message was received from the peer.
        Each time cbgpPeer2InUpdates is incremented,
        the value of this object is set to zero (0)."
    REFERENCE
        "RFC 4271, Section 4.3.
         RFC 4271, Section 8.2.2, Established state." 
    ::= { cbgpPeer2Entry 27 }

cbgpPeer2LastErrorTxt OBJECT-TYPE
    SYNTAX          SnmpAdminString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Implementation specific error description for
        bgpPeerLastErrorReceived." 
    ::= { cbgpPeer2Entry 28 }

cbgpPeer2PrevState OBJECT-TYPE
    SYNTAX          INTEGER  {
                        none(0),
                        idle(1),
                        connect(2),
                        active(3),
                        opensent(4),
                        openconfirm(5),
                        established(6)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP peer connection previous state."
    REFERENCE
        "RFC 1771, Section 8, A Border Gateway Protocol 4
         (BGP-4)." 
    ::= { cbgpPeer2Entry 29 }
 


cbgpPeer2CapsTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeer2CapsEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table contains the capabilities that are
        supported by a peer. Capabilities of a peer are
        received during BGP connection establishment.
        Values corresponding to each received capability
        are stored in this table. When a new capability
        is received, this table is updated with a new
        entry. When an existing capability is not received
        during the latest connection establishment, the
        corresponding entry is deleted from the table."
    REFERENCE
        "RFC 2842, Capabilities Advertisement with
         BGP-4.
         RFC 2818, Route Refresh Capability for BGP-4.
         RFC 2858, Multiprotocol Extensions for BGP-4.
         RFC 4724, Graceful Restart Mechanism for BGP.
         RFC 4893, BGP Support for Four-octet AS
         Number Space.
         draft-ietf-idr-add-paths-04.txt, Advertisement
         of Multiple Paths in BGP."
    ::= { cbgpPeer 6 }

cbgpPeer2CapsEntry OBJECT-TYPE
    SYNTAX          CbgpPeer2CapsEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Each entry represents a capability received from a
        peer with a particular code and an index. When a
        capability is received multiple times with different
        values during a BGP connection establishment,
        corresponding entries are differentiated with indices."
    INDEX           {
                        cbgpPeer2Type,
                        cbgpPeer2RemoteAddr,
                        cbgpPeer2CapCode,
                        cbgpPeer2CapIndex
                    } 
    ::= { cbgpPeer2CapsTable 1 }

CbgpPeer2CapsEntry ::= SEQUENCE {
        cbgpPeer2CapCode  INTEGER,
        cbgpPeer2CapIndex Unsigned32,
        cbgpPeer2CapValue OCTET STRING
}

cbgpPeer2CapCode OBJECT-TYPE
    SYNTAX          INTEGER  {
                        multiProtocol(1),
                        routeRefresh(2),
                        gracefulRestart(64),
                        fourByteAs(65),
                        addPath(69),
                        routeRefreshOld(128)
                    }
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The BGP Capability Advertisement Capability Code."
    REFERENCE
        "RFC 2842, Capabilities Advertisement with
         BGP-4.
         RFC 2818, Route Refresh Capability for BGP-4.
         RFC 2858, Multiprotocol Extensions for BGP-4.
         RFC 4724, Graceful Restart Mechanism for BGP.
         RFC 4893, BGP Support for Four-octet AS
         Number Space.
         draft-ietf-idr-add-paths-04.txt, Advertisement
         of Multiple Paths in BGP." 
    ::= { cbgpPeer2CapsEntry 1 }

cbgpPeer2CapIndex OBJECT-TYPE
    SYNTAX          Unsigned32 (1..128)
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Multiple instances of a given capability may be
        sent by a BGP speaker.  This variable is used
        to index them." 
    ::= { cbgpPeer2CapsEntry 2 }

cbgpPeer2CapValue OBJECT-TYPE
    SYNTAX          OCTET STRING (SIZE  (0..255))
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The value of the announced capability. This
        MIB object value is organized as given below,
            Capability : Route Refresh Capability
                         4-Byte AS Capability
                         Null string
            Capability : Multiprotocol Extensions
              +----------------------------------+
              | AFI(16 bits)                     |
              +----------------------------------+
              | SAFI (8 bits)                    |
              +----------------------------------+
            Capability : Graceful Restart
              +----------------------------------+
              | Restart Flags (4 bits)           |
              +----------------------------------+
              | Restart Time in seconds (12 bits)|
              +----------------------------------+
              | AFI(16 bits)                     |
              +----------------------------------+
              | SAFI (8 bits)                    |
              +----------------------------------+
              | Flags for Address Family (8 bits)|
              +----------------------------------+
              | ...                              |
              +----------------------------------+
              | AFI(16 bits)                     |
              +----------------------------------+
              | SAFI (8 bits)                    |
              +----------------------------------+
              | Flags for Address Family (8 bits)|
              +----------------------------------+
            Capability : Additional Paths
              +----------------------------------+
              | AFI(16 bits)                     |
              +----------------------------------+
              | SAFI (8 bits)                    |
              +----------------------------------+
              | Send/Receive (8 bits)            |
              +----------------------------------+"
    REFERENCE
        "RFC 2842, Capabilities Advertisement with
         BGP-4.
         RFC 2818, Route Refresh Capability for BGP-4.
         RFC 2858, Multiprotocol Extensions for BGP-4.
         RFC 4724, Graceful Restart Mechanism for BGP.
         RFC 4893, BGP Support for Four-octet AS
         Number Space.
         draft-ietf-idr-add-paths-04.txt, Advertisement
         of Multiple Paths in BGP." 
    ::= { cbgpPeer2CapsEntry 3 }
 


cbgpPeer2AddrFamilyTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeer2AddrFamilyEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table contains information related to
        address families supported by a peer. Supported
        address families of a peer are known during BGP
        connection establishment. When a new supported
        address family is known, this table is updated
        with a new entry. When an address family is not
        supported any more, corresponding entry is deleted
        from the table."
    ::= { cbgpPeer 7 }

cbgpPeer2AddrFamilyEntry OBJECT-TYPE
    SYNTAX          CbgpPeer2AddrFamilyEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is identified by an AFI/SAFI pair and
        peer address. It contains names associated with
        an address family."
    INDEX           {
                        cbgpPeer2Type,
                        cbgpPeer2RemoteAddr,
                        cbgpPeer2AddrFamilyAfi,
                        cbgpPeer2AddrFamilySafi
                    } 
    ::= { cbgpPeer2AddrFamilyTable 1 }

CbgpPeer2AddrFamilyEntry ::= SEQUENCE {
        cbgpPeer2AddrFamilyAfi  InetAddressType,
        cbgpPeer2AddrFamilySafi CbgpSafi,
        cbgpPeer2AddrFamilyName SnmpAdminString
}

cbgpPeer2AddrFamilyAfi OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The AFI index of the entry. An implementation
        is only required to support IPv4 unicast and
        VPNv4 (Value - 1) address families." 
    ::= { cbgpPeer2AddrFamilyEntry 1 }

cbgpPeer2AddrFamilySafi OBJECT-TYPE
    SYNTAX          CbgpSafi
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The SAFI index of the entry. An implementation
        is only required to support IPv4 unicast(Value
        - 1) and VPNv4( Value - 128) address families."
    REFERENCE
        "RFC 2858, Multiprotocol Extensions for BGP-4.
         RFC 2547, BGP/MPLS VPNs." 
    ::= { cbgpPeer2AddrFamilyEntry 2 }

cbgpPeer2AddrFamilyName OBJECT-TYPE
    SYNTAX          SnmpAdminString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Implementation specific Address Family name." 
    ::= { cbgpPeer2AddrFamilyEntry 3 }
 


cbgpPeer2AddrFamilyPrefixTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeer2AddrFamilyPrefixEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This table contains prefix related information
        related to address families supported by a peer.
        Supported address families of a peer are known
        during BGP connection establishment. When a new
        supported address family is known, this table
        is updated with a new entry. When an address
        family is not supported any more, corresponding
        entry is deleted from the table."
    ::= { cbgpPeer 8 }

cbgpPeer2AddrFamilyPrefixEntry OBJECT-TYPE
    SYNTAX          CbgpPeer2AddrFamilyPrefixEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is identified by an AFI/SAFI pair and
        peer address. It contains information associated
        with route prefixes belonging to an address family."
    INDEX           {
                        cbgpPeer2Type,
                        cbgpPeer2RemoteAddr,
                        cbgpPeer2AddrFamilyAfi,
                        cbgpPeer2AddrFamilySafi
                    } 
    ::= { cbgpPeer2AddrFamilyPrefixTable 1 }

CbgpPeer2AddrFamilyPrefixEntry ::= SEQUENCE {
        cbgpPeer2AcceptedPrefixes     Counter32,
        cbgpPeer2DeniedPrefixes       Gauge32,
        cbgpPeer2PrefixAdminLimit     Unsigned32,
        cbgpPeer2PrefixThreshold      Unsigned32,
        cbgpPeer2PrefixClearThreshold Unsigned32,
        cbgpPeer2AdvertisedPrefixes   Gauge32,
        cbgpPeer2SuppressedPrefixes   Gauge32,
        cbgpPeer2WithdrawnPrefixes    Gauge32
}

cbgpPeer2AcceptedPrefixes OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of accepted route prefixes on this connection,
        which belong to an address family." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 1 }

cbgpPeer2DeniedPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix, which
        belongs to an address family, received on this
        connection is denied. It is initialized to zero when
        the connection is undergone a hard reset." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 2 }

cbgpPeer2PrefixAdminLimit OBJECT-TYPE
    SYNTAX          Unsigned32 (1..4294967295)
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Max number of route prefixes accepted for an address
        family on this connection." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 3 }

cbgpPeer2PrefixThreshold OBJECT-TYPE
    SYNTAX          Unsigned32 (1..100)
    UNITS           "percent"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Prefix threshold value (%) for an address family
        on this connection at which warning message stating
        the prefix count is crossed the threshold or
        corresponding SNMP notification is generated." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 4 }

cbgpPeer2PrefixClearThreshold OBJECT-TYPE
    SYNTAX          Unsigned32 (1..100)
    UNITS           "percent"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Prefix threshold value (%) for an address family
        on this connection at which SNMP clear notification
        is generated if prefix threshold notification is
        already generated." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 5 }

cbgpPeer2AdvertisedPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix,
        which belongs to an address family is advertised
        on this connection. It is initialized to zero when
        the connection is undergone a hard reset." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 6 }

cbgpPeer2SuppressedPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix,
        which belongs to an address family is suppressed
        from being sent on this connection. It is
        initialized to zero when the connection is undergone
        a hard reset." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 7 }

cbgpPeer2WithdrawnPrefixes OBJECT-TYPE
    SYNTAX          Gauge32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This counter is incremented when a route prefix,
        which belongs to an address family, is withdrawn on
        this connection. It is initialized to zero when the
        connection is undergone a hard reset." 
    ::= { cbgpPeer2AddrFamilyPrefixEntry 8 }
 


cbgpPeer3Table OBJECT-TYPE
    SYNTAX          SEQUENCE OF CbgpPeer3Entry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "BGP peer table.  This table contains,
        one entry per BGP peer, information about
        the connections with BGP peers on per vrf basis"
    ::= { cbgpPeer 9 }

cbgpPeer3Entry OBJECT-TYPE
    SYNTAX          CbgpPeer3Entry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Entry containing information about the
        connection with a BGP peer in particular vrf"
    INDEX           {
                        cbgpPeer3VrfId,
                        cbgpPeer3Type,
                        cbgpPeer3RemoteAddr
                    } 
    ::= { cbgpPeer3Table 1 }

CbgpPeer3Entry ::= SEQUENCE {
        cbgpPeer3VrfId                         Unsigned32,
        cbgpPeer3Type                          InetAddressType,
        cbgpPeer3RemoteAddr                    InetAddress,
        cbgpPeer3VrfName                       SnmpAdminString,
        cbgpPeer3State                         INTEGER,
        cbgpPeer3AdminStatus                   INTEGER,
        cbgpPeer3NegotiatedVersion             Integer32,
        cbgpPeer3LocalAddr                     InetAddress,
        cbgpPeer3LocalPort                     InetPortNumber,
        cbgpPeer3LocalAs                       InetAutonomousSystemNumber,
        cbgpPeer3LocalIdentifier               IpAddress,
        cbgpPeer3RemotePort                    InetPortNumber,
        cbgpPeer3RemoteAs                      InetAutonomousSystemNumber,
        cbgpPeer3RemoteIdentifier              IpAddress,
        cbgpPeer3InUpdates                     Counter32,
        cbgpPeer3OutUpdates                    Counter32,
        cbgpPeer3InTotalMessages               Counter32,
        cbgpPeer3OutTotalMessages              Counter32,
        cbgpPeer3LastError                     OCTET STRING,
        cbgpPeer3FsmEstablishedTransitions     Counter32,
        cbgpPeer3FsmEstablishedTime            Gauge32,
        cbgpPeer3ConnectRetryInterval          Integer32,
        cbgpPeer3HoldTime                      Integer32,
        cbgpPeer3KeepAlive                     Integer32,
        cbgpPeer3HoldTimeConfigured            Integer32,
        cbgpPeer3KeepAliveConfigured           Integer32,
        cbgpPeer3MinASOriginationInterval      Integer32,
        cbgpPeer3MinRouteAdvertisementInterval Integer32,
        cbgpPeer3InUpdateElapsedTime           Gauge32,
        cbgpPeer3LastErrorTxt                  SnmpAdminString,
        cbgpPeer3PrevState                     INTEGER
}

cbgpPeer3VrfId OBJECT-TYPE
    SYNTAX          Unsigned32 (1..65535)
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "id of the vrf that peer is configured
        in." 
    ::= { cbgpPeer3Entry 1 }

cbgpPeer3Type OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Represents the type of Peer address stored
        in cbgpPeer3Entry." 
    ::= { cbgpPeer3Entry 2 }

cbgpPeer3RemoteAddr OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The remote IP address of this entry's BGP
        peer." 
    ::= { cbgpPeer3Entry 3 }

cbgpPeer3VrfName OBJECT-TYPE
    SYNTAX          SnmpAdminString (SIZE  (1..32))
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "name of the vrf that peer is configured
        in." 
    ::= { cbgpPeer3Entry 4 }

cbgpPeer3State OBJECT-TYPE
    SYNTAX          INTEGER  {
                        idle(1),
                        connect(2),
                        active(3),
                        opensent(4),
                        openconfirm(5),
                        established(6)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP peer connection state."
    REFERENCE       "RFC 4271, Section 8.2.2." 
    ::= { cbgpPeer3Entry 5 }

cbgpPeer3AdminStatus OBJECT-TYPE
    SYNTAX          INTEGER  {
                        stop(1),
                        start(2)
                    }
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The desired state of the BGP connection.
        A transition from 'stop' to 'start' will cause
        the BGP Manual Start Event to be generated.
        A transition from 'start' to 'stop' will cause
        the BGP Manual Stop Event to be generated.
        This parameter can be used to restart BGP peer
        connections.  Care should be used in providing
        write access to this object without adequate
        authentication."
    REFERENCE       "RFC 4271, Section 8.1.2." 
    ::= { cbgpPeer3Entry 6 }

cbgpPeer3NegotiatedVersion OBJECT-TYPE
    SYNTAX          Integer32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The negotiated version of BGP running between
        the two peers.

        This entry MUST be zero (0) unless the
        cbgpPeer3State is in the openconfirm or the
        established state.

        Note that legal values for this object are
        between 0 and 255."
    REFERENCE
        "RFC 4271, Section 4.2.
         RFC 4271, Section 7." 
    ::= { cbgpPeer3Entry 7 }

cbgpPeer3LocalAddr OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The local IP address of this entry's BGP
        connection." 
    ::= { cbgpPeer3Entry 8 }

cbgpPeer3LocalPort OBJECT-TYPE
    SYNTAX          InetPortNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The local port for the TCP connection between
        the BGP peers." 
    ::= { cbgpPeer3Entry 9 }

cbgpPeer3LocalAs OBJECT-TYPE
    SYNTAX          InetAutonomousSystemNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The local AS number for this session." 
    ::= { cbgpPeer3Entry 10 }

cbgpPeer3LocalIdentifier OBJECT-TYPE
    SYNTAX          IpAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP Identifier of this entry's BGP peer." 
    ::= { cbgpPeer3Entry 11 }

cbgpPeer3RemotePort OBJECT-TYPE
    SYNTAX          InetPortNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The remote port for the TCP connection
        between the BGP peers.  Note that the
        objects cbgpPeer3LocalAddr,
        cbgpPeer3LocalPort, cbgpPeer3RemoteAddr, and
        cbgpPeer3RemotePort provide the appropriate
        reference to the standard MIB TCP
        connection table." 
    ::= { cbgpPeer3Entry 12 }

cbgpPeer3RemoteAs OBJECT-TYPE
    SYNTAX          InetAutonomousSystemNumber
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The remote autonomous system number received in
        the BGP OPEN message."
    REFERENCE       "RFC 4271, Section 4.2." 
    ::= { cbgpPeer3Entry 13 }

cbgpPeer3RemoteIdentifier OBJECT-TYPE
    SYNTAX          IpAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP Identifier of this entry's BGP peer.
        This entry MUST be 0.0.0.0 unless the
        cbgpPeer3State is in the openconfirm or the
        established state."
    REFERENCE       "RFC 4271, Section 4.2, 'BGP Identifier'." 
    ::= { cbgpPeer3Entry 14 }

cbgpPeer3InUpdates OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The number of BGP UPDATE messages
        received on this connection."
    REFERENCE       "RFC 4271, Section 4.3." 
    ::= { cbgpPeer3Entry 15 }

cbgpPeer3OutUpdates OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The number of BGP UPDATE messages
        transmitted on this connection."
    REFERENCE       "RFC 4271, Section 4.3." 
    ::= { cbgpPeer3Entry 16 }

cbgpPeer3InTotalMessages OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The total number of messages received
        from the remote peer on this connection."
    REFERENCE       "RFC 4271, Section 4." 
    ::= { cbgpPeer3Entry 17 }

cbgpPeer3OutTotalMessages OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The total number of messages transmitted to
        the remote peer on this connection."
    REFERENCE       "RFC 4271, Section 4." 
    ::= { cbgpPeer3Entry 18 }

cbgpPeer3LastError OBJECT-TYPE
    SYNTAX          OCTET STRING (SIZE  (2))
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The last error code and subcode seen by this
        peer on this connection.  If no error has
        occurred, this field is zero.  Otherwise, the
        first byte of this two byte OCTET STRING
        contains the error code, and the second byte
        contains the subcode."
    REFERENCE       "RFC 4271, Section 4.5." 
    ::= { cbgpPeer3Entry 19 }

cbgpPeer3FsmEstablishedTransitions OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The total number of times the BGP FSM
        transitioned into the established state
        for this peer."
    REFERENCE       "RFC 4271, Section 8." 
    ::= { cbgpPeer3Entry 20 }

cbgpPeer3FsmEstablishedTime OBJECT-TYPE
    SYNTAX          Gauge32
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This timer indicates how long (in
        seconds) this peer has been in the
        established state or how long
        since this peer was last in the
        established state.  It is set to zero when
        a new peer is configured or when the router is
        booted."
    REFERENCE       "RFC 4271, Section 8." 
    ::= { cbgpPeer3Entry 21 }

cbgpPeer3ConnectRetryInterval OBJECT-TYPE
    SYNTAX          Integer32 (1..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        ConnectRetry timer.  The suggested value
        for this timer is 120 seconds."
    REFERENCE
        "RFC 4271, Section 8.2.2.  This is the value used
         to initialize the 'ConnectRetryTimer'." 
    ::= { cbgpPeer3Entry 22 }

cbgpPeer3HoldTime OBJECT-TYPE
    SYNTAX          Integer32 (0 | 3..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the Hold
        Timer established with the peer.  The
        value of this object is calculated by this
        BGP speaker, using the smaller of the
        values in cbgpPeer3HoldTimeConfigured and the
        Hold Time received in the OPEN message.

        This value must be at least three seconds
        if it is not zero (0).

        If the Hold Timer has not been established
        with the peer this object MUST have a value
        of zero (0).

        If the cbgpPeer3HoldTimeConfigured object has
        a value of (0), then this object MUST have a
        value of (0)."
    REFERENCE       "RFC 4271, Section 4.2." 
    ::= { cbgpPeer3Entry 23 }

cbgpPeer3KeepAlive OBJECT-TYPE
    SYNTAX          Integer32 (0 | 1..21845)
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the KeepAlive
        timer established with the peer.  The value
        of this object is calculated by this BGP
        speaker such that, when compared with
        cbgpPeer3HoldTime, it has the same proportion
        that cbgpPeer3KeepAliveConfigured has,
        compared with cbgpPeer3HoldTimeConfigured.

        If the KeepAlive timer has not been established
        with the peer, this object MUST have a value
        of zero (0).

        If the of cbgpPeer3KeepAliveConfigured object
        has a value of (0), then this object MUST have
        a value of (0)."
    REFERENCE       "RFC 4271, Section 4.4." 
    ::= { cbgpPeer3Entry 24 }

cbgpPeer3HoldTimeConfigured OBJECT-TYPE
    SYNTAX          Integer32 (0 | 3..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the Hold Time
        configured for this BGP speaker with this
        peer.  This value is placed in an OPEN
        message sent to this peer by this BGP
        speaker, and is compared with the Hold
        Time field in an OPEN message received
        from the peer when determining the Hold
        Time (cbgpPeer3HoldTime) with the peer.
        This value must not be less than three
        seconds if it is not zero (0).  If it is
        zero (0), the Hold Time is NOT to be
        established with the peer.  The suggested
        value for this timer is 90 seconds."
    REFERENCE
        "RFC 4271, Section 4.2.
         RFC 4271, Section 10." 
    ::= { cbgpPeer3Entry 25 }

cbgpPeer3KeepAliveConfigured OBJECT-TYPE
    SYNTAX          Integer32 (0 | 1..21845)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        KeepAlive timer configured for this BGP
        speaker with this peer.  The value of this
        object will only determine the
        KEEPALIVE messages' frequency relative to
        the value specified in
        cbgpPeer3HoldTimeConfigured; the actual
        time interval for the KEEPALIVE messages is
        indicated by cbgpPeer3KeepAlive.  A
        reasonable maximum value for this timer
        would be one third of that of
        cbgpPeer3HoldTimeConfigured.
        If the value of this object is zero (0),
        no periodical KEEPALIVE messages are sent
        to the peer after the BGP connection has
        been established.  The suggested value for
        this timer is 30 seconds."
    REFERENCE
        "RFC 4271, Section 4.4.
         RFC 4271, Section 10." 
    ::= { cbgpPeer3Entry 26 }

cbgpPeer3MinASOriginationInterval OBJECT-TYPE
    SYNTAX          Integer32 (1..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        MinASOriginationInterval timer.
        The suggested value for this timer is 15
        seconds."
    REFERENCE
        "RFC 4271, Section 9.2.1.2.
         RFC 4271, Section 10." 
    ::= { cbgpPeer3Entry 27 }

cbgpPeer3MinRouteAdvertisementInterval OBJECT-TYPE
    SYNTAX          Integer32 (1..65535)
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Time interval (in seconds) for the
        MinRouteAdvertisementInterval timer.
        The suggested value for this timer is 30
        seconds for EBGP connections and 5
        seconds for IBGP connections."
    REFERENCE
        "RFC 4271, Section 9.2.1.1.
         RFC 4271, Section 10." 
    ::= { cbgpPeer3Entry 28 }

cbgpPeer3InUpdateElapsedTime OBJECT-TYPE
    SYNTAX          Gauge32
    UNITS           "seconds"
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Elapsed time (in seconds) since the last BGP
        UPDATE message was received from the peer.
        Each time cbgpPeer3InUpdates is incremented,
        the value of this object is set to zero (0)."
    REFERENCE
        "RFC 4271, Section 4.3.
         RFC 4271, Section 8.2.2, Established state." 
    ::= { cbgpPeer3Entry 29 }

cbgpPeer3LastErrorTxt OBJECT-TYPE
    SYNTAX          SnmpAdminString
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Implementation specific error description for
        bgpPeerLastErrorReceived." 
    ::= { cbgpPeer3Entry 30 }

cbgpPeer3PrevState OBJECT-TYPE
    SYNTAX          INTEGER  {
                        none(0),
                        idle(1),
                        connect(2),
                        active(3),
                        opensent(4),
                        openconfirm(5),
                        established(6)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The BGP peer connection previous state."
    REFERENCE
        "RFC 1771, Section 8, A Border Gateway Protocol 4
         (BGP-4)." 
    ::= { cbgpPeer3Entry 31 }
 

-- Notifications

ciscoBgp4NotifyPrefix  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIB 0 }


cbgpFsmStateChange NOTIFICATION-TYPE
    OBJECTS         {
                        bgpPeerLastError,
                        bgpPeerState,
                        cbgpPeerLastErrorTxt,
                        cbgpPeerPrevState
                    }
    STATUS          current
    DESCRIPTION
        "The BGP cbgpFsmStateChange notification is generated
        for every BGP FSM state change. The bgpPeerRemoteAddr
        value is attached to the notification object ID."
   ::= { ciscoBgp4NotifyPrefix 1 }

cbgpBackwardTransition NOTIFICATION-TYPE
    OBJECTS         {
                        bgpPeerLastError,
                        bgpPeerState,
                        cbgpPeerLastErrorTxt,
                        cbgpPeerPrevState
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpBackwardTransition Event is generated when the
        BGP FSM moves from a higher numbered state to a lower
        numbered state. The bgpPeerRemoteAddr value is attached
        to the notification object ID."
   ::= { ciscoBgp4NotifyPrefix 2 }

cbgpPrefixThresholdExceeded NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeerPrefixAdminLimit,
                        cbgpPeerPrefixThreshold
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPrefixThresholdExceeded notification is
        generated when prefix count exceeds the configured
        warning threshold on a session for an address
        family. The bgpPeerRemoteAddr, cbgpPeerAddrFamilyAfi
        and cbgpPeerAddrFamilySafi values are attached to the
        notification object ID."
   ::= { ciscoBgp4NotifyPrefix 3 }

cbgpPrefixThresholdClear NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeerPrefixAdminLimit,
                        cbgpPeerPrefixClearThreshold
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPrefixThresholdClear notification is
        generated when prefix count drops below the configured
        clear threshold on a session for an address family once
        cbgpPrefixThresholdExceeded is generated. This won't
        be generated if the peer session goes down after the
        generation of cbgpPrefixThresholdExceeded.
        The bgpPeerRemoteAddr, cbgpPeerAddrFamilyAfi and
        cbgpPeerAddrFamilySafi values are attached to the
        notification object ID."
   ::= { ciscoBgp4NotifyPrefix 4 }

cbgpPeer2EstablishedNotification NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeer2LastError,
                        cbgpPeer2State
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPeer2EstablishedNotification notification
        is generated when the BGP FSM enters the established
        state."
   ::= { ciscoBgp4NotifyPrefix 5 }

cbgpPeer2BackwardTransNotification NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeer2LastError,
                        cbgpPeer2State
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPeer2BackwardTransNotification notification
        is generated when the BGP FSM moves from a higher
        numbered state to a lower numbered state."
   ::= { ciscoBgp4NotifyPrefix 6 }

cbgpPeer2FsmStateChange NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeer2LastError,
                        cbgpPeer2State,
                        cbgpPeer2LastErrorTxt,
                        cbgpPeer2PrevState
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPeer2FsmStateChange notification is generated
        for every BGP FSM state change."
   ::= { ciscoBgp4NotifyPrefix 7 }

cbgpPeer2BackwardTransition NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeer2LastError,
                        cbgpPeer2State,
                        cbgpPeer2LastErrorTxt,
                        cbgpPeer2PrevState
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPeer2BackwardTransition notification is
        generated when the BGP FSM moves from a higher numbered
        state to a lower numbered state."
   ::= { ciscoBgp4NotifyPrefix 8 }

cbgpPeer2PrefixThresholdExceeded NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeer2PrefixAdminLimit,
                        cbgpPeer2PrefixThreshold
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPeer2PrefixThresholdExceeded notification is
        generated when prefix count exceeds the configured
        warning threshold on a session for an address
        family."
   ::= { ciscoBgp4NotifyPrefix 9 }

cbgpPeer2PrefixThresholdClear NOTIFICATION-TYPE
    OBJECTS         {
                        cbgpPeer2PrefixAdminLimit,
                        cbgpPeer2PrefixClearThreshold
                    }
    STATUS          current
    DESCRIPTION
        "The cbgpPeer2PrefixThresholdClear notification is
        generated when prefix count drops below the configured
        clear threshold on a session for an address family once
        cbgpPeer2PrefixThresholdExceeded is generated.
        This will not be generated if the peer session goes down
        after the generation of cbgpPrefixThresholdExceeded."
   ::= { ciscoBgp4NotifyPrefix 10 }
-- ciscoBgp4NotificationPrefix is deprecated.
-- Do not define any objects and/or notifications
-- under this OID.

ciscoBgp4NotificationPrefix  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIB 2 }

-- conformance information

ciscoBgp4MIBConformance  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIB 3 }

ciscoBgp4MIBCompliances  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIBConformance 1 }

ciscoBgp4MIBGroups  OBJECT IDENTIFIER
    ::= { ciscoBgp4MIBConformance 2 }


-- Compliance statements

ciscoBgp4MIBCompliance MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
        "The compliance statement for entities which implement
        the Cisco BGP4 MIB"
    MODULE          -- this module
    MANDATORY-GROUPS { ciscoBgp4RouteGroup }
    ::= { ciscoBgp4MIBCompliances 1 }

ciscoBgp4MIBComplianceRev1 MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
        "The compliance statement for entities which implement
        the Cisco BGP4 MIB"
    MODULE          -- this module
    MANDATORY-GROUPS {
                        ciscoBgp4RouteGroup,
                        ciscoBgp4PeerGroup,
                        ciscoBgp4NotificationsGroup
                    }

    OBJECT          cbgpRouteAggregatorAddrType
    SYNTAX          INTEGER  {
                        ipv4(1)
                    }
    DESCRIPTION
        "An implementation is only required to support
        IPv4 address type for aggregator address."

    OBJECT          cbgpRouteAggregatorAddr
    SYNTAX          InetAddress (SIZE (4))
    DESCRIPTION
        "An implementation is only required to support
        IPv4 address type for aggregator address."

    OBJECT          cbgpPeerPrefixLimit
    SYNTAX          Unsigned32 (1..4294967295)
    MIN-ACCESS      read-only
    DESCRIPTION
        "SET operation is not supported on this object"
    ::= { ciscoBgp4MIBCompliances 2 }

ciscoBgp4MIBComplianceRev2 MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
        "The compliance statement for entities which implement
        the Cisco BGP4 MIB"
    MODULE          -- this module
    MANDATORY-GROUPS {
                        ciscoBgp4RouteGroup,
                        ciscoBgp4PeerGroup1,
                        ciscoBgp4NotificationsGroup1
                    }

    OBJECT          cbgpRouteAggregatorAddrType
    SYNTAX          INTEGER  {
                        ipv4(1)
                    }
    DESCRIPTION
        "An implementation is only required to support
        IPv4 address type."

    OBJECT          cbgpRouteAggregatorAddr
    SYNTAX          OCTET STRING (SIZE (0..4))
    DESCRIPTION
        "An implementation is only required to support
        IPv4 address type."

    OBJECT          cbgpPeerPrefixAdminLimit
    MIN-ACCESS      read-only
    DESCRIPTION
        "SET operation is not supported on this object"

    OBJECT          cbgpPeerPrefixThreshold
    MIN-ACCESS      read-only
    DESCRIPTION
        "SET operation is not supported on this object"
    ::= { ciscoBgp4MIBCompliances 3 }

ciscoBgp4MIBComplianceRev3 MODULE-COMPLIANCE
    STATUS          current
    DESCRIPTION
        "The compliance statement for entities which implement
        the Cisco BGP4 MIB"
    MODULE          -- this module
    MANDATORY-GROUPS {
                        ciscoBgp4RouteGroup,
                        ciscoBgp4PeerGroup1,
                        ciscoBgp4GlobalGroup,
                        ciscoBgp4NotificationsGroup1
                    }

    GROUP           ciscoBgp4Peer2Group
    DESCRIPTION
        "This group is unconditionally optional."

    GROUP           ciscoBgp4Peer2NotificationsGroup
    DESCRIPTION
        "This group is unconditionally optional."

    OBJECT          cbgpRouteAggregatorAddrType
    SYNTAX          INTEGER  {
                        ipv4(1)
                    }
    DESCRIPTION
        "An implementation is only required to support
        IPv4 address type."

    OBJECT          cbgpRouteAggregatorAddr
    SYNTAX          OCTET STRING (SIZE (0..4))
    DESCRIPTION
        "An implementation is only required to support
        IPv4 address type."

    OBJECT          cbgpPeerPrefixAdminLimit
    MIN-ACCESS      read-only
    DESCRIPTION
        "Write access is not required."

    OBJECT          cbgpPeerPrefixThreshold
    MIN-ACCESS      read-only
    DESCRIPTION
        "Write access is not required."

    OBJECT          cbgpPeer2LocalAddr
    SYNTAX          OCTET STRING (SIZE (0..4))
    DESCRIPTION
        "An implementation is only required to support
        IPv4 address type."

    OBJECT          cbgpNotifsEnable
    MIN-ACCESS      read-only
    DESCRIPTION
        "Write access is not required."

    OBJECT          cbgpPeer2PrefixAdminLimit
    MIN-ACCESS      read-only
    DESCRIPTION
        "Write access is not required."

    OBJECT          cbgpPeer2PrefixThreshold
    MIN-ACCESS      read-only
    DESCRIPTION
        "Write access is not required."
    ::= { ciscoBgp4MIBCompliances 4 }

-- Units of conformance

ciscoBgp4RouteGroup OBJECT-GROUP
    OBJECTS         {
                        cbgpRouteOrigin,
                        cbgpRouteASPathSegment,
                        cbgpRouteNextHop,
                        cbgpRouteMedPresent,
                        cbgpRouteMultiExitDisc,
                        cbgpRouteLocalPrefPresent,
                        cbgpRouteLocalPref,
                        cbgpRouteAtomicAggregate,
                        cbgpRouteAggregatorAS,
                        cbgpRouteAggregatorAddrType,
                        cbgpRouteAggregatorAddr,
                        cbgpRouteBest,
                        cbgpRouteUnknownAttr
                    }
    STATUS          current
    DESCRIPTION
        "A collection of objects providing information
        about routes received by BGP speaker."
    ::= { ciscoBgp4MIBGroups 1 }

ciscoBgp4PeerGroup OBJECT-GROUP
    OBJECTS         {
                        cbgpPeerPrefixAccepted,
                        cbgpPeerPrefixDenied,
                        cbgpPeerPrefixLimit,
                        cbgpPeerPrefixAdvertised,
                        cbgpPeerPrefixSuppressed,
                        cbgpPeerPrefixWithdrawn
                    }
    STATUS          deprecated
    DESCRIPTION
        "A collection of objects providing information
        about routes received by BGP speaker."
    ::= { ciscoBgp4MIBGroups 2 }

ciscoBgp4NotificationsGroup NOTIFICATION-GROUP
   NOTIFICATIONS    { cbgpFsmStateChange }
    STATUS          deprecated
    DESCRIPTION
        "The collection of notifications related to BGP."
    ::= { ciscoBgp4MIBGroups 3 }

ciscoBgp4PeerGroup1 OBJECT-GROUP
    OBJECTS         {
                        cbgpPeerPrevState,
                        cbgpPeerLastErrorTxt,
                        cbgpPeerCapValue,
                        cbgpPeerAddrFamilyName,
                        cbgpPeerAcceptedPrefixes,
                        cbgpPeerDeniedPrefixes,
                        cbgpPeerPrefixAdminLimit,
                        cbgpPeerPrefixThreshold,
                        cbgpPeerPrefixClearThreshold,
                        cbgpPeerAdvertisedPrefixes,
                        cbgpPeerSuppressedPrefixes,
                        cbgpPeerWithdrawnPrefixes
                    }
    STATUS          current
    DESCRIPTION
        "A collection of objects providing information
        about a BGP peer."
    ::= { ciscoBgp4MIBGroups 4 }

ciscoBgp4NotificationsGroup1 NOTIFICATION-GROUP
   NOTIFICATIONS    {
                        cbgpFsmStateChange,
                        cbgpBackwardTransition,
                        cbgpPrefixThresholdExceeded,
                        cbgpPrefixThresholdClear
                    }
    STATUS          current
    DESCRIPTION
        "The collection of notifications related to BGP."
    ::= { ciscoBgp4MIBGroups 5 }

ciscoBgp4Peer2Group OBJECT-GROUP
    OBJECTS         {
                        cbgpPeer2State,
                        cbgpPeer2AdminStatus,
                        cbgpPeer2NegotiatedVersion,
                        cbgpPeer2LocalAddr,
                        cbgpPeer2LocalPort,
                        cbgpPeer2LocalAs,
                        cbgpPeer2LocalIdentifier,
                        cbgpPeer2RemotePort,
                        cbgpPeer2RemoteAs,
                        cbgpPeer2RemoteIdentifier,
                        cbgpPeer2InUpdates,
                        cbgpPeer2OutUpdates,
                        cbgpPeer2InTotalMessages,
                        cbgpPeer2OutTotalMessages,
                        cbgpPeer2LastError,
                        cbgpPeer2FsmEstablishedTransitions,
                        cbgpPeer2FsmEstablishedTime,
                        cbgpPeer2ConnectRetryInterval,
                        cbgpPeer2HoldTime,
                        cbgpPeer2KeepAlive,
                        cbgpPeer2HoldTimeConfigured,
                        cbgpPeer2KeepAliveConfigured,
                        cbgpPeer2MinASOriginationInterval,
                        cbgpPeer2MinRouteAdvertisementInterval,
                        cbgpPeer2InUpdateElapsedTime,
                        cbgpPeer2LastErrorTxt,
                        cbgpPeer2PrevState,
                        cbgpPeer2CapValue,
                        cbgpPeer2AddrFamilyName,
                        cbgpPeer2AcceptedPrefixes,
                        cbgpPeer2DeniedPrefixes,
                        cbgpPeer2PrefixAdminLimit,
                        cbgpPeer2PrefixThreshold,
                        cbgpPeer2PrefixClearThreshold,
                        cbgpPeer2AdvertisedPrefixes,
                        cbgpPeer2SuppressedPrefixes,
                        cbgpPeer2WithdrawnPrefixes
                    }
    STATUS          current
    DESCRIPTION
        "A collection of objects providing information
        about a BGP peer."
    ::= { ciscoBgp4MIBGroups 6 }

ciscoBgp4Peer2NotificationsGroup NOTIFICATION-GROUP
   NOTIFICATIONS    {
                        cbgpPeer2EstablishedNotification,
                        cbgpPeer2BackwardTransNotification,
                        cbgpPeer2FsmStateChange,
                        cbgpPeer2BackwardTransition,
                        cbgpPeer2PrefixThresholdExceeded,
                        cbgpPeer2PrefixThresholdClear
                    }
    STATUS          current
    DESCRIPTION
        "A collection of notifications related to BGP."
    ::= { ciscoBgp4MIBGroups 7 }

ciscoBgp4GlobalGroup OBJECT-GROUP
    OBJECTS         {
                        cbgpNotifsEnable,
                        cbgpLocalAs
                    }
    STATUS          current
    DESCRIPTION
        "A collection of global objects related to BGP."
    ::= { ciscoBgp4MIBGroups 8 }

END