# Bear Frame Upgrade 2.1


## Print Settings

:warning: Warning: It is important to follow the recommended print settings and to **calibrate your extrusion multiplier** before printing the parts (for each and every spool that you use). [Check our calibration guide here](https://guides.bear-lab.com/Guide/Extrusion+multiplier+and+filament+diameter/8).

* Filament type: PETG
* Slicer: PrusaSlicer
* Infill type : Gyroid recommended
* Support : No
* Brim : No
* Detect thin walls : No
* Perimeters width (internal and external) : 0.45mm


| Part | Quantity | Layer<br/>Height<br/>[mm] | Infill [%] | Num.<br/>Perimeters | Num.<br/>Top / Bottom<br/>Layers | Note |
|:-----|:--------:|:-------------------------:|:----------:|:-------------------:|:--------------------------------:|:-----|
| build_helper_y         | 1 | 0.20 | 20 | 3 | 5 | :warning: Print a single part                     |
| build_helper_z         | 1 | 0.20 | 20 | 3 | 5 | :warning: Print a single part                     |
| cable_clip_horizontal  | 2 | 0.20 | 20 | 4 | 5 |                                                   |
| cable_clip_lcd         | 5 | 0.20 | 20 | 4 | 5 |                                                   |
| cable_clip_vertical    | 6 | 0.20 | 20 | 4 | 5 |                                                   |
| foot                   | 4 | 0.20 | 20 | 3 | 5 |                                                   |
| lcd_support_a          | 1 | 0.20 | 20 | 3 | 5 |                                                   |
| lcd_support_b          | 1 | 0.20 | 20 | 3 | 5 |                                                   |
| psu_lower_mount        | 1 | 0.20 | 20 | 3 | 5 | File name may vary depending your PSU version     |
| psu_upper_mount        | 2 | 0.20 | 20 | 3 | 5 | File name may vary depending your PSU version     |
| rambo_base_lower_mount | 1 | 0.20 | 20 | 3 | 5 |                                                   |
| rambo_base_upper_mount | 1 | 0.20 | 20 | 3 | 5 |                                                   |
| rambo_hinge_lower      | 1 | 0.20 | 20 | 3 | 5 | File name may vary depending your printer version |
| rambo_hinge_upper      | 1 | 0.20 | 20 | 3 | 5 | File name may vary depending your printer version |
| y_bearing_holder       | 3 | 0.20 | 20 | 5 | 5 |                                                   |
| y_belt_holder          | 1 | 0.20 | 20 | 4 | 5 |                                                   |
| y_end_caps             | 2 | 0.20 | 20 | 3 | 5 | Total of 4 printed parts                          |
| y_idler_mount          | 1 | 0.20 | 20 | 4 | 5 |                                                   |
| y_idler_tensioner      | 1 | 0.20 | 20 | 4 | 5 |                                                   |
| y_motor_endstop_mount  | 1 | 0.20 | 20 | 4 | 5 | :warning: Only for MK2(S) or MK2.5(S)             |
| y_motor_mount          | 1 | 0.20 | 20 | 4 | 5 |                                                   |
| y_rod_holder           | 4 | 0.20 | 20 | 4 | 5 |                                                   |
| z_end_caps             | 1 | 0.20 | 20 | 3 | 5 | Total of 2 printed parts                          |
| z_leadscrew_cap        | 2 | 0.20 | 20 | 2 | 5 |                                                   |
| z_motor_mounts         | 1 | 0.20 | 20 | 4 | 5 | Total of 2 printed parts                          |
| z_tops                 | 1 | 0.20 | 20 | 4 | 5 | Total of 2 printed parts                          |