//removeIf(en_lang_disabled)
//english
var englishtrans = {
"en":"English",
"STA":"Client Station",
"AP":"Access Point",
"BT":"Bluetooth",
"Hold:0":"Hold complete. Ready to resume.",
"Hold:1":"Hold in-progress. Reset will throw an alarm.",
"Door:0":"Door closed. Ready to resume.",
"Door:1":"Machine stopped. Door still ajar. Can't resume until closed.",
"Door:2":"Door opened. Hold (or parking retract) in-progress. Reset will throw an alarm.",
"Door:3":"Door closed and resuming. Restoring from park, if applicable. Reset will throw an alarm.",
"ALARM:1":"Hard limit has been triggered. Machine position is likely lost due to sudden halt. Re-homing is highly recommended.",
"ALARM:2":"Soft limit alarm. G-code motion target exceeds machine travel. Machine position retained. Alarm may be safely unlocked, click the Reset Button.",
"ALARM:3":"Reset while in motion. Machine position is likely lost due to sudden halt. Re-homing is highly recommended.",
"ALARM:4":"Probe fail. Probe is not in the expected initial state before starting probe cycle.",
"ALARM:5":"Probe fail. Probe did not contact the workpiece within the programmed travel for G38.2 and G38.4.",
"ALARM:6":"Homing fail. The active homing cycle was reset.",
"ALARM:7":"Homing fail. Safety door was opened during homing cycle.",
"ALARM:8":"Homing fail. Pull off travel failed to clear limit switch. Try increasing pull-off setting or check wiring.",
"ALARM:9":"Homing fail. Could not find limit switch within search distances. Try increasing max travel, decreasing pull-off distance, or check wiring.",
"error:1":"G-code words consist of a letter and a value. Letter was not found.",
"error:2":"Missing the expected G-code word value or numeric value format is not valid.",
"error:3":"Grbl '$' system command was not recognized or supported.",
"error:4":"Negative value received for an expected positive value.",
"error:5":"Homing cycle failure. Homing is not enabled via settings.",
"error:6":"Minimum step pulse time must be greater than 3usec.",
"error:7":"An EEPROM read failed. Auto-restoring affected EEPROM to default values.",
"error:8":"Grbl '$' command cannot be used unless Grbl is IDLE. Ensures smooth operation during a job.",
"error:9":"G-code commands are locked out during alarm or jog state.",
"error:10":"Soft limits cannot be enabled without homing also enabled.",
"error:11":"Max characters per line exceeded. Received command line was not executed.",
"error:12":"Grbl '$' setting value cause the step rate to exceed the maximum supported.",
"error:13":"Safety door detected as opened and door state initiated.",
"error:14":"Build info or startup line exceeded EEPROM line length limit. Line not stored.",
"error:15":"Jog target exceeds machine travel. Jog command has been ignored.",
"error:16":"Jog command has no '=' or contains prohibited g-code.",
"error:17":"Laser mode requires PWM output.",
"error:20":"Unsupported or invalid g-code command found in block.",
"error:21":"More than one g-code command from same modal group found in block.",
"error:22":"Feed rate has not yet been set or is undefined.",
"error:23":"G-code command in block requires an integer value.",
"error:24":"More than one g-code command that requires axis words found in block.",
"error:25":"Repeated g-code word found in block.",
"error:26":"No axis words found in block for g-code command or current modal state which requires them.",
"error:27":"Line number value is invalid.",
"error:28":"G-code command is missing a required value word.",
"error:29":"G59.x work coordinate systems are not supported.",
"error:30":"G53 only allowed with G0 and G1 motion modes.",
"error:31":"Axis words found in block when no command or current modal state uses them.",
"error:32":"G2 and G3 arcs require at least one in-plane axis word.",
"error:33":"Motion command target is invalid.",
"error:34":"Arc radius value is invalid.",
"error:35":"G2 and G3 arcs require at least one in-plane offset word.",
"error:36":"Unused value words found in block.",
"error:37":"G43.1 dynamic tool length offset is not assigned to configured tool length axis.",
"error:38":"Tool number greater than max supported value.",
"error:60":"SD failed to mount",
"error:61":"SD card failed to open file for reading",
"error:62":"SD card failed to open directory",
"error:63":"SD Card directory not found",
"error:64":"SD Card file empty",
"error:70":"Bluetooth failed to start",
};
//endRemoveIf(en_lang_disabled)