//zh_TW //removeIf(zh_tw_lang_disabled) //use https://www.mobilefish.com/services/unicode_converter/unicode_converter.php var zh_TW_trans = { "zh_tw":"繁體中文", "ESP3D for":"ESP3D for", "Value of auto-check must be between 0s and 99s !!":"自動檢查的值必須在0s到99s之間!!", "Value of extruder velocity must be between 1 mm/min and 9999 mm/min !":"擠出機速度值必須在1 毫米/分鐘至9999 毫米/分鐘之間！", "Value of filament length must be between 0.001 mm and 9999 mm !":"燈絲長度的值必須在0.001 毫米和9999 毫米之間！", "cannot have '-', '#' char or be empty":"不能含有 '-', '#' 或 空字元", "cannot have '-', 'e' char or be empty":"不能含有 '-', 'e' 或 空字元", "Failed:":"失敗:", "File config / config.txt not found!":"找不到檔案 config / config.txt!", "File name cannot be empty!":"檔名不能為空!", "Value must be ":"值必須為 ", "Value must be between 0 degres and 999 degres !":"值必須在 0 到 999 之間 !", "Value must be between 0% and 100% !":"值必須在 0% 到 100% 之間 !", "Value must be between 25% and 150% !":"值必須在 25% 到 150% 之間 !", "Value must be between 50% and 300% !":"值必須在 50% 到 300% 之間 !", "XY feedrate value must be between 1 mm/min and 9999 mm/min !":"XY進給率值必須在 1 毫米/分鐘 and 9999 毫米/分鐘 之間!", "Z feedrate value must be between 1 mm/min and 999 mm/min !":"Z進給率值必須在 1 毫米/分鐘 and 999 毫米/分鐘 之間!", " seconds":" 秒", "Abort":"終止", "auto-check every:":"自動檢查每隔:", "auto-check position every:":"自動檢查位置每隔:", "Autoscroll":"自動滾動", "Max travel":"最大行程", "Feed rate":"進給率", "Touch plate thickness":"Touch plate thickness", "Bed":"熱床", "Board":"主機板", "Busy...":"忙...", "Camera":"攝像機", "Cancel":"取消", "Cannot get EEPROM content!":"無法獲取EEPROM內容!", "Clear":"清除", "Close":"關閉", "Color":"顏色", "Commands":"命令", "Communication locked by another process, retry later.":"通訊被另一個程序鎖定，請稍後重試.", "Communication locked!":"通訊已鎖定!", "Communications are currently locked, please wait and retry.":"通訊當前處於鎖定狀態，請稍後重試.", "Confirm deletion of directory: ":"確認刪除目錄: ", "Confirm deletion of file: ":"確認刪除檔案: ", "Connecting ESP3D...":"正在連線 ESP3D...", "Connection failed! is your FW correct?":"連線失敗!您的韌體正確嗎?", "Controls":"控制", "Credits":"Credits", "Dashboard":"儀表盤", "Data mofified":"資料已修改", "Do you want to save?":"您要儲存嗎?", "Enable second extruder controls":"啟用第二擠出機", "Error":"錯誤", "ESP3D Filesystem":"ESP3D 檔案系統", "ESP3D Settings":"ESP3D 設定", "ESP3D Status":"ESP3D 狀態", "ESP3D Update":"ESP3D 更新", "Extrude":"進料", "Extruder T0":"擠出機 T0", "Extruder T1":"擠出機 T1", "Extruders":"擠出機", "Fan (0-100%)":"風扇速度 (0-100%)", "Feed (25-150%)":"送料 (25-150%)", "Feedrate :":"送料速度 :", "Filename":"檔名", "Filename/URI":"Filename/URI", "Verbose mode":"詳細模式", "Firmware":"韌體", "Flow (50-300%)":"流量 (50-300%)", "Heater T0":"加熱頭 T0", "Heater T1":"加熱頭 T1", "Help":"幫助", "Icon":"圖示", "Interface":"介面", "Join":"加入", "Label":"標籤", "List of available Access Points":"可用AP列表", "Macro Editor":"巨集命令編輯器", "mm":"毫米", "mm/min":"毫米/分鐘", "Motors off":"關閉電機", "Name":"名稱", "Name:":"名稱:", "Network":"網路", "No SD card detected":"未檢測到SD卡", "No":"No", "Occupation:":"Occupation:", "Ok":"Ok", "Options":"選項", "Out of range":"超出範圍", "Please Confirm":"請確認", "Please enter directory name":"請輸入目錄名稱", "Please wait...":"請稍候...", "Printer configuration":"印表機配置", "GRBL configuration":"GRBL 配置", "Printer":"印表機", "Progress":"進度", "Protected":"受保護", "Refresh":"重新整理", "Restart ESP3D":"重啟 ESP3D", "Restarting ESP3D":"正在重啟 ESP3D", "Restarting":"正在重啟", "Restarting, please wait....":"正在重新啟動，請稍候....", "Retry":"重試", "Reverse":"回抽", "Save macro list failed!":"儲存巨集列表失敗!", "Save":"儲存", "Saving":"正在儲存", "Scanning":"正在掃描", "SD Files":"SD檔案", "sec":"秒", "Send Command...":"傳送命令...", "Send":"傳送", "Set failed":"設定失敗", "Set":"設定", "Signal":"訊號", "Size":"尺寸", "SSID":"SSID", "Target":"目標", "Temperatures":"溫度", "Total:":"總計:", "Type":"型別", "Update Firmware ?":"更新韌體嗎 ?", "Update is ongoing, please wait and retry.":"更新正在進行，請稍後重試.", "Update":"更新", "Upload failed : ":"上傳失敗 : ", "Upload failed":"上傳失敗", "Upload":"上傳", "Uploading ":"正在上傳 ", "Upload done":"上傳完成", "Used:":"使用:", "Value | Target":"當前值 | 預設值", "Value":"值", "Wrong data":"錯誤的資料", "Yes":"Yes", "Light":"燈", "None":"無", "Modem":"調變解調器", "STA":"客戶端模式", "AP":"AP模式", "BT":"藍芽", "Baud Rate":"波特率", "Sleep Mode":"睡眠模式", "Web Port":"Web埠", "Data Port":"資料埠", "Hostname":"主機名", "Wifi mode":"Wifi模式", "Station SSID":"網路名稱", "Station Password":"密碼", "Station Network Mode":"客戶端網路模式", "Station IP Mode":"客戶端IP模式", "DHCP":"DHCP", "Static":"靜態", "Station Static IP":"客戶端靜態IP", "Station Static Mask":"Station Static Mask", "Station Static Gateway":"Station Static Gateway", "AP SSID":"AP SSID", "AP Password":"AP密碼", "AP Network Mode":"AP Network Mode", "SSID Visible":"SSID可見", "AP Channel":"AP頻道", "Open":"Open", "Authentication":"身份驗證", "AP IP Mode":"AP IP Mode", "AP Static IP":"AP Static IP", "AP Static Mask":"AP Static Mask", "AP Static Gateway":"AP Static Gateway", "Time Zone":"Time Zone", "Day Saving Time":"Day Saving Time", "Time Server 1":"Time Server 1", "Time Server 2":"Time Server 2", "Time Server 3":"Time Server 3", "Target FW":"Target FW", "Direct SD access":"直接SD訪問", "Direct SD Boot Check":"直接SD引導檢查", "Primary SD":"Primary SD", "Secondary SD":"Secondary SD", "Temperature Refresh Time":"溫度重新整理時間", "Position Refresh Time":"位置重新整理時間", "Status Refresh Time":"狀態重新整理時間", "XY feedrate":"XY進給率", "Z feedrate":"Z進給率", "E feedrate":"E進給率", "Camera address":"攝像機地址", "Setup":"設定", "Start setup":"開始設定", "This wizard will help you to configure the basic settings.":"此嚮導將幫助您配置基本設定.", "Press start to proceed.":"按開始進行.", "Save your printer's firmware base:":"儲存印表機的韌體庫:", "This is mandatory to get ESP working properly.":"這是正常執行ESP所必需的.", "Save your printer's board current baud rate:":"儲存印表機主機板的當前波特率:", "Printer and ESP board must use same baud rate to communicate properly.":"印表機和ESP板必須使用相同的波特率才能正確通訊.", "Continue":"繼續", "WiFi Configuration":"WiFi配置", "Define ESP role:":"Define ESP role:", "AP define access point / STA allows to join existing network":"AP模式自定義接入點 / STA模式加入現有網路", "What access point ESP need to be connected to:":"What access point ESP need to be connected to:", "You can use scan button, to list available access points.":"您可以使用掃描按鈕列出可用的網路.", "Password to join access point:":"Password to join access point:", "Define ESP name:":"Define ESP name:", "What is ESP access point SSID:":"What is ESP access point SSID:", "Password for access point:":"AP訪問密碼:", "Define security:":"定義安全性:", "SD Card Configuration":"SD卡配置", "Is ESP connected to SD card:":"ESP是否連線到SD卡:", "Check update using direct SD access:":"使用直接SD訪問檢查更新:", "SD card connected to ESP":"SD卡連線到ESP", "SD card connected to printer":"SD卡連線到印表機", "Setup is finished.":"設定完成.", "After closing, you will still be able to change or to fine tune your settings in main interface anytime.":"關閉後，您仍然可以隨時在主介面中更改或微調設定.", "You may need to restart the board to apply the new settings and connect again.":"您可能需要重新啟動主機板來應用新的設定並重新連線.", "Identification requested":"Identification requested", "admin":"admin", "user":"user", "guest":"guest", "Identification invalid!":"Identification invalid!", "Passwords do not matches!":"密碼不匹配!", "Password must be >1 and <16 without space!":"密碼須為2-15位且沒有空格!", "User:":"User:", "Password:":"Password:", "Submit":"提交", "Change Password":"更改密碼", "Current Password:":"當前密碼:", "New Password:":"新密碼:", "Confirm New Password:":"確認新密碼:", "Error : Incorrect User":"錯誤: 不正確的使用者名稱", "Error: Incorrect password":"錯誤: 不正確的密碼", "Error: Missing data":"錯誤: 缺少資料", "Error: Cannot apply changes":"錯誤: 無法應用更改", "Error: Too many connections":"錯誤: 連線過多", "Authentication failed!":"驗證失敗!", "Serial is busy, retry later!":"序列口忙，請稍後重試!", "Login":"登入", "Log out":"登出", "Password":"密碼", "No SD Card":"沒有SD卡", "Check for Update":"檢查更新", "Please use 8.3 filename only.":"只能使用8.3檔名.", "Preferences":"偏好", "Feature":"功能", "Show camera panel":"顯示攝像機面板", "Auto load camera":"自動載入攝像機", "Enable bed controls":"啟用熱床控制元件", "Enable fan controls":"啟用風扇控制元件", "Enable Z controls":"啟用Z軸控制元件", "Panels":"面板", "Show control panel":"顯示控制面板", "Show temperatures panel":"顯示溫度面板", "Show extruder panel":"顯示擠出機面板", "Show files panel":"顯示檔案面板", "Show GRBL panel":"顯示GRBL面板", "Show commands panel":"顯示命令面板", "Select files":"選擇檔案", "Select file":"選擇檔案", "$n files":"$n 檔案", "No file chosen":"未選擇檔案", "Length":"Length", "Output msg":"Output msg", "Enable":"啟用", "Disable":"禁用", "Serial":"序列口", "Chip ID":"晶片ID", "CPU Frequency":"CPU頻率", "CPU Temperature":"CPU溫度", "Free memory":"可用記憶體", "Flash Size":"快閃記憶體容量", "Available Size for update":"可用的更新大小", "Available Size for SPIFFS":"可用的SPIFFS大小", "Baud rate":"波特率", "Sleep mode":"睡眠模式", "Channel":"頻道", "Phy Mode":"Phy Mode", "Web port":"Web埠", "Data port":"資料埠", "Active Mode":"活動模式", "Connected to":"已連線到", "IP Mode":"IP模式", "Gateway":"Gateway", "Mask":"掩碼", "DNS":"DNS", "Disabled Mode":"禁用模式", "Captive portal":"Captive portal", "Enabled":"啟用", "Web Update":"Web升級", "Pin Recovery":"Pin Recovery", "Disabled":"禁用", "Target Firmware":"目標韌體", "SD Card Support":"SD卡支援", "Time Support":"時間支援", "M117 output":"M117輸出", "Oled output":"Oled輸出", "Serial output":"序列輸出", "Web socket output":"Web socket輸出", "TCP output":"TCP輸出", "FW version":"FW版本", "Show DHT output":"Show DHT輸出", "DHT Type":"DHT型別", "DHT check (seconds)":"DHT檢查(秒)", "SD speed divider":"SD speed divider", "Number of extruders":"擠出機數量", "Mixed extruders":"混合擠出機", "Extruder":"擠出機", "Enable lock interface":"啟用鎖定介面", "Lock interface":"鎖定介面", "Unlock interface":"解鎖介面", "You are disconnected":"您已斷開連線", "Looks like you are connected from another place, so this page is now disconnected":"您已從另一個位置連線，因此本頁面現在已斷開連線", "Please reconnect me":"請重新連線", "Mist":"冷卻噴霧", "Flood":"冷卻液", "Spindle":"主軸", "Connection monitoring":"連線監視", "XY Feedrate value must be at least 1 mm/min!":"XY Feedrate value must be at least 1 毫米/分鐘!", "Z Feedrate value must be at least 1 mm/min!":"Z Feedrate value must be at least 1 毫米/分鐘!", "Hold:0":"已完成。準備恢復。", "Hold:1":"進行中。重置將發出警報。", "Door:0":"門已關閉。準備恢復。", "Door:1":"機器停止了。門仍然開著。直到關門後才能恢復。", "Door:2":"門開啟。保持（或停車縮回）進行中。復位將發出警報。", "Door:3":"門已關閉並正在恢復。從停車處恢復（如果適用）。重置將引發警報。", "ALARM:1":"已觸發硬極限。由於突然停止,機器位置可能丟失。強烈建議重新回原點。", "ALARM:2":"軟限位警報。G程式碼運動目標超出了機器行程。保留了機器位置。可以安全地解除警報,請單擊復位按鈕。", "ALARM:3":"運動時復位。由於突然停止,機器位置可能會丟失。強烈建議重新回原點。", "ALARM:4":"探測失敗。在開始探測迴圈之前,探測未處於預期的初始狀態。", "ALARM:5":"探測失敗。在G38.2和G38.4的程式設計行程內,測頭未與工件接觸。", "ALARM:6":"回原點失敗。復位了有效的回原點週期。", "ALARM:7":"回原點失敗。在回原點週期中安全門開啟。", "ALARM:8":"回原點失敗。拉出行程未能清除限位開關。嘗試增加拉出設定或檢查接線。", "ALARM:9":"回原點失敗。無法在搜尋距離內找到限位開關。請嘗試增加最大行程,減小下拉距離或檢查接線。", "error:1":"G碼字由一個字母和一個值組成。找不到字母。", "error:2":"缺少預期的G程式碼字值或數值格式無效。", "error:3":"未識別或不支援Grbl'$'系統命令。", "error:4":"接收到的負值為期望的正值。", "error:5":"回原點迴圈失敗。未通過設定啟用回原點。", "error:6":"最小步進脈衝時間必須大於3usec。", "error:7":"EEPROM讀取失敗。將受影響的EEPROM自動恢復為預設值。", "error:8":"除非Grbl為IDLE,否則無法使用Grbl'$'命令。確保作業期間的平穩操作。", "error:9":"在報警或慢進狀態期間,G程式碼命令被鎖定。", "error:10":"在未啟用回原點的情況下也無法啟用軟限制。", "error:11":"每行超出最大字元。未執行接收到的命令列。", "error:12":"Grbl'$'設定值導致步速超過支援的最大值。", "error:13":"檢測到安全門已開啟並且門狀態已啟動。", "error:14":"構建資訊或啟動行超出EEPROM行長度限制。行未儲存。", "error:15":"點動目標超出了機器行程。點動命令已被忽略。", "error:16":"點動命令沒有'='或包含禁止的g程式碼。", "error:17":"鐳射模式需要PWM輸出。", "error:20":"在塊中發現不支援或無效的g程式碼命令。", "error:21":"在塊中找到的同一模態組中有多個g程式碼命令。", "error:22":"進紙速度尚未設定或未定義。", "error:23":"塊中的G程式碼命令需要一個整數值。", "error:24":"有多個g程式碼命令,需要在塊中找到軸字。", "error:25":"在塊中找到重複的g碼字。", "error:26":"在g程式碼命令或需要它們的當前模態下,在程式段中找不到軸字。", "error:27":"行號值無效。", "error:28":"G程式碼命令缺少必需的值字。", "error:29":"不支援G59.x工作座標系。", "error:30":"G53僅在G0和G1運動模式下允許。", "error:31":"當沒有命令或當前模態使用它們時,在塊中找到軸字。", "error:32":"G2和G3圓弧至少需要一個平面內軸字。", "error:33":"運動命令目標無效。", "error:34":"圓弧半徑值無效。", "error:35":"G2和G3圓弧至少需要一個平面內偏移字。", "error:36":"在塊中找到未使用的價值詞。", "error:37":"G43.1動態刀具長度補償未分配給已組態的刀具長度軸。", "error:38":"刀具編號大於最大支援值。", "error:60":"SD無法掛載", "error:61":"SD卡無法開啟檔案進行讀取", "error:62":"SD卡無法開啟目錄", "error:63":"找不到SD卡目錄", "error:64":"SD卡檔案為空", "error:70":"藍芽無法啟動", "Max travel":"最大行程", "Plate thickness":"探針資料修正", "Show probe panel":"顯示探針面板", "Probe":"探針", "Start Probe":"啟動探針", "Touch status":"對刀狀態", "Value of maximum probe travel must be between 1 mm and 9999 mm !":"最大探頭行程值必須在 1 毫米 至 9999 毫米之間!", "Value of probe touch plate thickness must be between 0 mm and 9999 mm !":"探針資料修正值必須在 0 毫米 至 9999 毫米之間!", "Value of probe feedrate must be between 1 mm/min and 9999 mm/min !":"探針進給率值必須在 1 毫米/分鐘 至 9999 毫米/分鐘之間!", "Probe failed !":"探測失敗 !", "Probe result saved.":"探測結果已儲存.", "Browser:":"瀏覽:", "Probing...":"正在探測...", "Step pulse, microseconds":"步進脈衝, 微秒", "Step idle delay, milliseconds":"步進電機空閒時釋放力矩時間,255是一直保持", "Step port invert, mask":"步進脈衝翻轉介面, mask", "Direction port invert, mask":"方向翻轉介面, mask", "Step enable invert, boolean":"步進使能翻轉, boolean", "Limit pins invert, boolean":"限位引腳翻轉, boolean", "Probe pin invert, boolean":"探測引腳翻轉, boolean", "Status report, mask":"狀態報告, mask", "Junction deviation, mm":"結偏差, mm", "Arc tolerance, mm":"圓弧公差, mm", "Report inches, boolean":"報告英寸, boolean", "Soft limits, boolean":"是否啟用軟體最大行程限制, boolean", "Hard limits, boolean":"是否啟用硬體限位, boolean", "Homing cycle, boolean":"是否啟用$H回限位操作, boolean", "Homing dir invert, mask":"復位方向翻轉", "Homing feed, mm/min":"復位尋找速度, 毫米/分鐘", "Homing seek, mm/min":"復位給進速度, 毫米/分鐘", "Homing debounce, milliseconds":"位消抖, 毫秒", "Homing pull-off, mm":"復位返回行程, 毫米", "Max spindle speed, RPM":"最大主軸轉速, RPM", "Min spindle speed, RPM":"最小主軸轉速, RPM", "Laser mode, boolean":"鐳射模式, boolean", "X steps/mm":"X軸電機 步數/毫米,走1mm脈衝數", "Y steps/mm":"Y軸電機 步數/毫米,走1mm脈衝數", "Z steps/mm":"Z軸電機 步數/毫米,走1mm脈衝數", "X Max rate, mm/min":"X軸最大速率, 毫米/分鐘", "Y Max rate, mm/min":"Y軸最大速率, 毫米/分鐘", "Z Max rate, mm/min":"Z軸最大速率, 毫米/分鐘", "X Acceleration, mm/sec^2":"X軸加速度，毫米/秒^2", "Y Acceleration, mm/sec^2":"Y軸加速度，毫米/秒^2", "Z Acceleration, mm/sec^2":"Z軸加速度，毫米/秒^2", "X Max travel, mm":"X軸最大行程，毫米", "Y Max travel, mm":"Y軸最大行程，毫米", "Z Max travel, mm":"Z軸最大行程，毫米", "File extensions (use ; to separate):":"副檔名 (使用 ; 分隔):", }; //endRemoveIf(zh_tw_lang_disabled)