█████╗ ███╗ ██╗████████╗██╗██╗ ██╗██╗ ██╗███╗ ██╗████████╗███████╗██████╗ ██╔══██╗████╗ ██║╚══██╔══╝██║██║ ██║██║ ██║████╗ ██║╚══██╔══╝██╔════╝██╔══██╗ ███████║██╔██╗ ██║ ██║ ██║███████║██║ ██║██╔██╗ ██║ ██║ █████╗ ██████╔╝ ██╔══██║██║╚██╗██║ ██║ ██║██╔══██║██║ ██║██║╚██╗██║ ██║ ██╔══╝ ██╔══██╗ ██║ ██║██║ ╚██╗█║ ██║ ██║██║ ██║╚██████╔╝██║ ╚████║ ██║ ███████╗██║ ██║ ╚═╝ ╚═╝╚═╝ ╚═══╝ ╚═╝ ╚═╝╚═╝ ╚═╝ ╚═════╝ ╚═╝ ╚═══╝ ╚═╝ ╚══════╝╚═╝ ╚═╝ D I G I N O D E ================================================================================ WELCOME, OPERATOR ================================================================================ You've got the PCB. Populate it with the core components and you've got a fully functional DIGI Node — WiFi/BLE scanner, drone Remote ID detector, LoRa mesh endpoint, GPS, RTC, tamper sensing. Want the full experience? Add the enclosure, antennas, and power kit for a deployable field unit. ================================================================================ [01] BUILD IT ================================================================================ Assembly manual (full walkthrough): https://github.com/lukeswitz/AntiHunter/blob/main/hw/Prototype_STL_Files/Antihunter-DIGINODE-AssemblyManual.pdf Most components are drop-in and solder. Two need a small mod depending on what shipped to you: >> RTC MODULE Usually ships with female headers. Trim and reuse the existing pins, or desolder and swap in male pin headers. >> VIBRATION SENSOR Sourced units have inverted 90° headers. Heat all three joints and bend straight (trim excess), or desolder and replace with standard header pins. ================================================================================ [02] FLASH THE MESH RADIO ================================================================================ Flash your Heltec V3.2 (preferred) or T114 with the latest stable Meshtastic firmware. Then open the Meshtastic app or web config and set: SERIAL ........ Enabled MODE .......... TEXTMSG BAUD .......... 115200 PINS .......... 10 RX / 9 TX (T114) 19 RX / 20 TX (Heltec V3) Disconnect when done. ================================================================================ [03] FLASH ANTIHUNTER ================================================================================ Flash the ESP32-S3 on the AntiHunter PCB. Two variants: >> FULL ......... WiFi AP for the web UI, plus mesh command control >> HEADLESS ..... No AP, quieter field ops, mesh commands only Pick one method: [A] WEB FLASHER https://lukeswitz.github.io/AntiHunter [B] CLI INSTALLER curl -fsSL -o flashAntihunter.sh https://raw.githubusercontent.com/lukeswitz/AntiHunter/main/Dist/flashAntihunter.sh chmod +x flashAntihunter.sh ./flashAntihunter.sh [C] BUILD FROM SOURCE Flash with PlatformIO — see the README. ================================================================================ [04] CONFIGURE ================================================================================ Tune device settings from the same web tool, send mesh commands later, or batch-apply settings during flashing. Your node is now operational. Deploy and tune to taste. ================================================================================ /!\ POWER /!\ ================================================================================ ALWAYS power from a regulated 5V source — USB or the included UPS board. Unregulated input can damage the board components. ================================================================================ [05] TIPS AND REFERENCE ================================================================================ >> Turn off the public mesh channel; use your own encrypted channel as primary >> Disable Bluetooth on the radio for quieter field ops >> Pull the screen on the Heltec V3 to save power >> Use a little petroleum jelly on the TPU seals if in extreme conditions DOCS / MESH COMMANDS / API / FEATURES https://github.com/lukeswitz/AntiHunter BETA CHANNEL Early features to test before they hit stable COMMAND CENTER PRO Multi-site federation with TAK, MQTT, ADSB integration Perimeter deployment strategy tool https://github.com/TheRealSirHaXalot/AntiHunter-Command-Control-PRO Fully open source; Write your own mesh commands, Wire in your IDS. Make it yours. ================================================================================ BILL OF MATERIALS ================================================================================ ---- CORE (minimum for a functional node) ------------------------------------- 1x Seeed XIAO ESP32-S3 1x Heltec WiFi LoRa 32 V3.2 (or T114 — V3.2 preferred) 1x ATGM336H GPS module 1x MicroSD SPI reader + 16GB FAT32 card 1x SW-420 vibration sensor 1x DS3231 RTC module ---- FULL BUILD :: POWER & ENCLOSURE ------------------------------------------ 1x Type-C 15W 3A 5V UPS (2S 18650, 88x41x22mm) 1x 30mm 5V JST fan 1x 3-pin mini on/off switch 1x JST power male cable (switch to board) 1x Weatherproof enclosure STLs: https://github.com/lukeswitz/AntiHunter/tree/main/hw/Prototype_STL_Files ---- FULL BUILD :: ANTENNAS & CABLES ------------------------------------------ 3x U.FL to SMA pigtail (10cm, SMA bulkhead) 1x 6dBi 2.4GHz antenna (WiFi/BLE) 1x 6dBi LoRa antenna (868 EU / 915 US / 923 Asia) 1x GNSS helix antenna (L1/L2/L5) ---- FULL BUILD :: FASTENERS -------------------------------------------------- 6x JST 2.54 2-pin terminals (2.0mm JST also fits) 10x M3 inserts 2x M3x15mm brass standoffs 1x 1/4" tripod insert 8x M3 flat-top screws (enclosure) 6x M3 screws (PCB and power board) ================================================================================ -- END OF FILE -- ================================================================================