# generated by PrusaSlicer 2.6.0+MacOS-arm64 on 2023-07-23 at 16:51:20 UTC

[print:0.20 - Creality K1]
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 12000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.2
enable_dynamic_overhang_speeds = 1
external_perimeter_acceleration = 5000
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 120
external_perimeters_first = 0
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 13
extruder_clearance_radius = 45
extrusion_width = 0.45
fill_angle = 45
fill_density = 5%
fill_pattern = grid
first_layer_acceleration = 500
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.5
first_layer_height = 0.2
first_layer_speed = 40
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 60
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 12000
infill_anchor = 2
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_overlap = 10%
infill_speed = 300
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_max_width = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}.gcode
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 80%
overhangs = 1
perimeter_acceleration = 8000
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_generator = arachne
perimeter_speed = 300
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.2
raft_expansion = 1.5
raft_first_layer_density = 80%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 3
skirts = 0
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 60
solid_infill_acceleration = 8000
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 200
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 0
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.37
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 5
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 70%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_style = snug
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 80%
support_tree_angle = 40
support_tree_angle_slow = 25
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 5
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 15%
thick_bridges = 0
thin_walls = 0
threads = 12
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.42
top_solid_infill_acceleration = 5000
top_solid_infill_speed = 60
top_solid_layers = 5
top_solid_min_thickness = 0.7
travel_acceleration = 0
travel_speed = 500
travel_speed_z = 12
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 170
wipe_tower_y = 140
xy_size_compensation = 0

[filament:Nobufil ABSx - K1]
bed_temperature = 110
bridge_fan_speed = 60
compatible_printers = "Creality K1"
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 0
disable_fan_first_layers = 4
enable_dynamic_fan_speeds = 0
end_filament_gcode = "; Filament-specific end gcode\nSET_TEMPERATURE_FAN_TARGET TEMPERATURE_FAN=chamber TARGET=40"
extrusion_multiplier = 0.95
fan_always_on = 1
fan_below_layer_time = 30
filament_colour = #FFF2EC
filament_cooling_final_speed = 50
filament_cooling_initial_speed = 10
filament_cooling_moves = 5
filament_cost = 27.82
filament_density = 1.04
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 15
filament_loading_speed = 14
filament_loading_speed_start = 19
filament_max_volumetric_speed = 19
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 0
filament_toolchange_delay = 0
filament_type = ABS
filament_unload_time = 12
filament_unloading_speed = 20
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = nil
first_layer_bed_temperature = 105
first_layer_temperature = 270
full_fan_speed_layer = 0
idle_temperature = 100
inherits = 
max_fan_speed = 15
min_fan_speed = 40
min_print_speed = 15
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
slowdown_below_layer_time = 20
start_filament_gcode = "; Filament-specific start gcode\nSET_TEMPERATURE_FAN_TARGET TEMPERATURE_FAN=chamber TARGET=50"
temperature = 270

[printer:Creality K1]
autoemit_temperature_commands = 0
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,220x0,220x220,0x220
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n
between_objects_gcode = 
color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Nobufil ABSx - Creality K1"
default_print_profile = "0.20 - Creality K1"
deretract_speed = 40
end_gcode = END_PRINT\n; total layers count = [total_layer_count]
extra_loading_move = -2
extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = klipper
high_current_on_filament_swap = 0
host_type = prusalink
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nSET_PRINT_STATS_INFO CURRENT_LAYER={layer_num + 1}
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 2500
machine_max_acceleration_extruding = 18000
machine_max_acceleration_retracting = 1200
machine_max_acceleration_travel = 2000
machine_max_acceleration_x = 18000
machine_max_acceleration_y = 18000
machine_max_acceleration_z = 200
machine_max_feedrate_e = 100
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 40
machine_max_jerk_e = 10
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 2
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.3
max_print_height = 250
min_layer_height = 0.07
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = PAUSE
print_host = 
printer_model = 
printer_notes = Do not remove the keywords below.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_K1
printer_settings_id = 
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 1
retract_before_travel = 1.5
retract_before_wipe = 80%
retract_layer_change = 1
retract_length = 0.5
retract_length_toolchange = 4
retract_lift = 0.4
retract_lift_above = 0
retract_lift_below = 240
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = M82 ;absolute extrusion mode\nM140 S0\nM104 S0 \nSET_PRINT_STATS_INFO TOTAL_LAYER=[total_layer_count]\nSTART_PRINT EXTRUDER_TEMP={first_layer_temperature[0]} BED_TEMP=[first_layer_bed_temperature]
template_custom_gcode = 
thumbnails = 96x96,32x32,300x300
thumbnails_format = PNG
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[presets]
print = 0.20 - Creality K1
sla_print = 
sla_material = 
printer = Creality K1
filament = Nobufil ABSx - Creality K1