RADLAN-Physicaldescription-MIB DEFINITIONS ::= BEGIN -- Version: 7.36 -- Date: 05 Apr 2004 -- -- 30-Jan-2004 Add rlPhdUnitGenParamTable -- 30-Jan-2004 Add rlPhdUnitEnvParamTable -- 24-Feb-2004 Add rlPhdStackOrderTopUnit -- 24-Feb-2004 Add rlPhdStackOrderBottomUnit -- 24-Feb-2004 Add rlPhdStackOrderPermutation IMPORTS OBJECT-TYPE, MODULE-IDENTITY FROM SNMPv2-SMI DisplayString FROM SNMPv2-TC PhysAddress FROM SNMPv2-TC JackType FROM MAU-MIB rnd FROM RADLAN-MIB RlEnvMonState FROM RADLAN-HWENVIROMENT EntitySensorStatus, EntitySensorValue FROM ENTITY-SENSOR-MIB TRAP-TYPE FROM RFC-1215 rndErrorDesc, rndErrorSeverity FROM RADLAN-MIB; rlPhysicalDescription MODULE-IDENTITY LAST-UPDATED "200310180000Z" ORGANIZATION "" CONTACT-INFO "" DESCRIPTION "The private MIB module definition for physical device configuration." REVISION "200310180000Z" DESCRIPTION "Initial version of this MIB." ::= { rnd 53 } rlPhdMibVersion OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "MIB's version, the current version is 3. 1: original version 2: a. new tables rlPhdModuleHotSwapTable rlPhdStackOrderTable b. new scalars rlPhdStackReorder rlPhdNumberOfUnits rlPhdMaxNumberOfUnits 3: a. new field rlPhdModuleRole of rlPhdModuleTable b. new scalars rlPhdForceMasterUnit 4: a. new fields rlPhdModuleConnect1 and rlPhdModuleConnect2 of rlPhdModuleTable. 5: a. Prefix rlPhD were replaced by prefix rlPhd b. fields rlPhdModuleConnect1 and rlPhdModuleConnect2 are moved from rlPhdModuleTable to rlPhdStackTable. c. new fiels rlPhdStackSofrwareVer, rlPhdStackProductID and rlPhdStackMacAddr of rlPhdStackTable. d. new scalars rlPhdStackReloadUnit e. new scalars rlPhdStackOrderTopUnit rlPhdStackOrderBottomUnit rlPhdStackOrderPermutation" ::= { rlPhysicalDescription 1 } rlPhdModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF RlPhdModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each module (board) there is an entry describing it in this module" ::= { rlPhysicalDescription 2 } rlPhdModuleEntry OBJECT-TYPE SYNTAX RlPhdModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry of this table specifies a module (board)" INDEX { rlPhdModuleStackUnit, rlPhdModuleIndex} ::= { rlPhdModuleTable 1 } RlPhdModuleEntry ::= SEQUENCE { rlPhdModuleStackUnit INTEGER, rlPhdModuleIndex INTEGER, rlPhdModuleType INTEGER, rlPhdModuleStartingPort INTEGER, rlPhdModuleNumberOfPorts INTEGER, rlPhdModuleRow INTEGER, rlPhdModuleColumn INTEGER, rlPhdModuleRole INTEGER } rlPhdModuleStackUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The stack unit to which this module belongs." ::= { rlPhdModuleEntry 1 } rlPhdModuleIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of the module in its stack unit" ::= { rlPhdModuleEntry 2 } rlPhdModuleType OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The module type: 1 - unknown 2 - extension 3 - acceleratorOpal 4 - acceleratorHertz3 5 - acceleratorUhual3 6 - hertz2 7 - uhual2 8 - hertz3 9 - uhual3ge 10 - uhual3sonet 11 - uhual3atm 12 - bcm2402 13 - lg8-0 14 - lg16-0 15 - lg8-1 16 - hertz2plus 17 - uhual2plus 18 - 2 98MX620 19 - 2 98EX120 20 - 1 98EX110 21 - two herz3 copper 22 - two uhaul3 fiber SX 23 - two uhaul3 copper 24 - hertz3 fiber 25 - two uhaul3 gibic 26 - two herz3 fiber 27 - two uhaul3 fiber LX 28 - bcm5615 stackable 24 29 - bcm5625x2 stackable 48 30 - EX125D-24 Giga ports 31 - EX115D-48 Fast 4 Giga 32 - SICC 4 copper ports 33 - SICC 4 fiber ports 34 - SICC gbic ports 35 - VesuvioT 36 - VesuvioF 37 - 98DX160 38 - 98DX240 39 - 98DX162 40 - 98DX242 41 - Gemstones Sapphire only 42 - Gemstones 24F+4G 43 - Gemstones 48F+4G 44 - Cheetah 24G + 3XG 45 - Cheetah 48G stacking" ::= { rlPhdModuleEntry 3 } rlPhdModuleStartingPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The minimal number of the port residing on this module." ::= { rlPhdModuleEntry 4 } rlPhdModuleNumberOfPorts OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ports residing on this module." ::= { rlPhdModuleEntry 5} rlPhdModuleRow OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "On which row (the uppermost being numbered 1 and the highest row number asigned to the lowest row) this module resides within the chassis of its stack unit." ::= { rlPhdModuleEntry 6 } rlPhdModuleColumn OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "On which column (the leftmost being numbered 1 and the highest column number asigned to the rightmost column) this module resides within the chassis of its stack unit." ::= { rlPhdModuleEntry 7 } rlPhdModuleRole OBJECT-TYPE SYNTAX INTEGER { standalone(1), master(2), backup(3), slave(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The module role in the stack." DEFVAL { standalone } ::= { rlPhdModuleEntry 8 } rlPhdPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF RlPhdPortsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Lists the physical or physical-related attributes of ports" ::= { rlPhysicalDescription 3 } rlPhdPortsEntry OBJECT-TYPE SYNTAX RlPhdPortsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each port, a entry describing attributes which are either physical or are derived from the features of the device hardware" INDEX { rlPhdPortsIfIndex } ::= { rlPhdPortsTable 1 } RlPhdPortsEntry ::= SEQUENCE { rlPhdPortsIfIndex INTEGER, rlPhdPortsIfIndexName DisplayString(SIZE(1..20)), rlPhdPortsMediaType INTEGER, rlPhdPortsStackUnit INTEGER, rlPhdPortsModuleNumber INTEGER, rlPhdPortsRow INTEGER, rlPhdPortsColumn INTEGER, rlPhdConnectorType JackType, rlPhdPortHaul INTEGER } rlPhdPortsIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The L2 interface number associated with this port." ::= { rlPhdPortsEntry 1 } rlPhdPortsIfIndexName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The L2 interface number associated with this port, in string format based on the overall hardware architecture of the device (i.e., for monolithic devices just numbers, devices composed of modules (boards, cards) or stackable devices composed of monolithic units in form - , stackable devices in which each unit is composed of modules - - " ::= { rlPhdPortsEntry 2 } rlPhdPortsMediaType OBJECT-TYPE SYNTAX INTEGER {copper(1), optic-fiber(2), combo(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "The media type of this port." ::= { rlPhdPortsEntry 3 } rlPhdPortsStackUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of the stack unit to which this port belongs." ::= { rlPhdPortsEntry 4 } rlPhdPortsModuleNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of the module to which this port belongs." ::= { rlPhdPortsEntry 5 } rlPhdPortsRow OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "On which row (the uppermost being numbered 1 and the highest row number asigned to the lowest row) this port resides within its module." ::= { rlPhdPortsEntry 6 } rlPhdPortsColumn OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "On which column (the leftmost being numbered 1 and the highest column number asigned to the rightmost column) this this port resides within its module." ::= { rlPhdPortsEntry 7 } rlPhdConnectorType OBJECT-TYPE SYNTAX JackType MAX-ACCESS read-only STATUS current DESCRIPTION "Type of connector." ::= { rlPhdPortsEntry 8 } rlPhdPortHaul OBJECT-TYPE SYNTAX INTEGER { not-relevant(1), short(2), long(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Distance supported by this port." ::= { rlPhdPortsEntry 9 } rlPhdStackTable OBJECT-TYPE SYNTAX SEQUENCE OF RlPhdStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each stack unit there is an entry describing it in this table" ::= { rlPhysicalDescription 4 } rlPhdStackEntry OBJECT-TYPE SYNTAX RlPhdStackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry of this table specifies a stack unit" INDEX { rlPhdStackUnit } ::= { rlPhdStackTable 1 } RlPhdStackEntry ::= SEQUENCE { rlPhdStackUnit INTEGER, rlPhdStackType INTEGER, rlPhdStackConnect1 INTEGER, rlPhdStackConnect2 INTEGER, rlPhdStackSofrwareVer DisplayString, rlPhdStackProductID DisplayString, rlPhdStackMacAddr PhysAddress } rlPhdStackUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The stack unit described by this entry." ::= { rlPhdStackEntry 1 } rlPhdStackType OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the stack unit described by this entry: 1 - box 3202 2 - box LG 3 - bcm 4 - prestera" ::= { rlPhdStackEntry 2 } rlPhdStackConnect1 OBJECT-TYPE SYNTAX INTEGER (0..8) MAX-ACCESS read-only STATUS current DESCRIPTION "The unit number connected to the Hyper GLink left side connection - 0 means not connected; other integer indicates the unit number." DEFVAL { 0 } ::= { rlPhdStackEntry 3 } rlPhdStackConnect2 OBJECT-TYPE SYNTAX INTEGER (0..8) MAX-ACCESS read-only STATUS current DESCRIPTION "The unit number connected to the Hyper GLink right side connection - 0 means not connected; other integer indicates the unit number." DEFVAL { 0 } ::= { rlPhdStackEntry 4 } rlPhdStackSofrwareVer OBJECT-TYPE SYNTAX DisplayString (SIZE (1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Software version of the unit." ::= { rlPhdStackEntry 5 } rlPhdStackProductID OBJECT-TYPE SYNTAX DisplayString (SIZE (1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Product ID of the unit." ::= { rlPhdStackEntry 6 } rlPhdStackMacAddr OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The physical (MAC) address of the unit." ::= { rlPhdStackEntry 7 } rlPhdModuleHotSwapTable OBJECT-TYPE SYNTAX SEQUENCE OF RlPhdModuleHotSwapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each module (board) there is an entry describing its Hot Swap status" ::= { rlPhysicalDescription 5 } rlPhdModuleHotSwapEntry OBJECT-TYPE SYNTAX RlPhdModuleHotSwapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry of this table specifies a module (board) Hot Swap status" INDEX { rlPhdModuleStackUnit, rlPhdModuleIndex} ::= { rlPhdModuleHotSwapTable 1 } RlPhdModuleHotSwapEntry ::= SEQUENCE { rlPhdModuleHotSwapAdminStatus INTEGER, rlPhdModuleHotSwapOperStatus INTEGER } rlPhdModuleHotSwapAdminStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired state of the module. The off(1) state indicates that the module is not used and its rlPhdModuleHotSwapOperStatus is always off(2). The on{1) state indicates that the module may be used and its rlPhdModuleHotSwapOperStatus will be on(1) if it presents and off(2) if it does not present." DEFVAL { on } ::= { rlPhdModuleHotSwapEntry 1 } rlPhdModuleHotSwapOperStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current Hot Swap state of the module. If rlPhdModuleHotSwapAdminStatus is down(2) then rlPhdModuleHotSwapOperStatus should be down(2). If rlPhdModuleHotSwapAdminStatus is changed to up(1) then rlPhdModuleHotSwapOperStatus should change to up(1) if the module presents; it should remain in the down(2) state if and only if the module does not present." ::= { rlPhdModuleHotSwapEntry 2 } rlPhdStackOrderTable OBJECT-TYPE SYNTAX SEQUENCE OF RlPhdStackOrderEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table enables the user to configure the order of the stack units as displayed on his GUI. The order of the entries in this table corresponds to the last configured order. If the stack units order was never configured, the order will be the same as in the rlPhdStackTable." ::= { rlPhysicalDescription 6 } rlPhdStackOrderEntry OBJECT-TYPE SYNTAX RlPhdStackOrderEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry of this table specifies a stack unit in the position desired by the user" INDEX { rlPhdStackOrderCurrentUnitPosition } ::= { rlPhdStackOrderTable 1 } RlPhdStackOrderEntry ::= SEQUENCE { rlPhdStackOrderCurrentUnitPosition INTEGER, rlPhdStackOrderDesiredUnitPosition INTEGER, rlPhdStackOrderUnitIndex INTEGER, rlPhdStackOrderUnitType INTEGER } rlPhdStackOrderCurrentUnitPosition OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The current stack unit position." ::= { rlPhdStackOrderEntry 1 } rlPhdStackOrderDesiredUnitPosition OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The desired stack unit position. Note that setting this MIB object will take effect only after setting the rlPhdStackReorder MIB object below. After setting this MIB object and until a further change of at least one instance of the rlPhdStackOrderDesiredUnitPosition object, the values of the rlPhdStackOrderCurrentUnitPosition objectinstance and the corresponding rlPhdStackOrderDesiredUnitPosition object instance will be the same." ::= { rlPhdStackOrderEntry 2 } rlPhdStackOrderUnitIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the original unit index, i.e. has the same value as rlPhdStackUnit above." ::= { rlPhdStackOrderEntry 3 } rlPhdStackOrderUnitType OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the stack unit described by this entry. It has the same value as rlPhdStackType above. This information is duplicated here only for easier retrieval by the device manager." ::= { rlPhdStackOrderEntry 4 } rlPhdStackReorder OBJECT-TYPE SYNTAX INTEGER {reorder(1)} MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this MIB object will cause the settings of the rlPhdStackOrderDesiredUnitPosition MIB object instances to take effect. After setting this MIB object and until a further change of at least one instance of the rlPhdStackOrderDesiredUnitPosition object, the values of the rlPhdStackOrderCurrentUnitPosition objectinstance and the corresponding rlPhdStackOrderDesiredUnitPosition object instance will be the same." ::= { rlPhysicalDescription 7 } rlPhdNumberOfUnits OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the current number of units in the stack." ::= { rlPhysicalDescription 8 } rlPhdMaxNumberOfUnits OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Shows the maximum number of units in the stack." ::= { rlPhysicalDescription 9 } rlPhdForceMasterUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Force unit to be master." ::= { rlPhysicalDescription 10 } -- The following scalar isn't suported and will be removed rlPhdStackFixedUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Determine which unit will be on bottom/top of list on Show-List command(see ." ::= { rlPhysicalDescription 11 } -- The following scalar isn't suported and will be removed rlPhdStackFixedUnitLocation OBJECT-TYPE SYNTAX INTEGER{ bottom(1), top(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Determine the bottom/top object in the stack table." ::= { rlPhysicalDescription 12 } rlPhdStackReloadUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Reset a specific unit." ::= { rlPhysicalDescription 13 } rlPhdUnitGenParamTable OBJECT-TYPE SYNTAX SEQUENCE OF RlPhdUnitGenParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each module (board) there is an entry describing it in this module" ::= { rlPhysicalDescription 14 } rlPhdUnitGenParamEntry OBJECT-TYPE SYNTAX RlPhdUnitGenParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry of this table specifies a module (board)" INDEX { rlPhdUnitGenParamStackUnit} ::= { rlPhdUnitGenParamTable 1 } RlPhdUnitGenParamEntry ::= SEQUENCE { rlPhdUnitGenParamStackUnit INTEGER, rlPhdUnitGenParamSoftwareVersion DisplayString, rlPhdUnitGenParamFirmwareVersion DisplayString, rlPhdUnitGenParamHardwareVersion DisplayString, rlPhdUnitGenParamSerialNum DisplayString, rlPhdUnitGenParamAssetTag DisplayString, rlPhdUnitGenParamServiceTag DisplayString } rlPhdUnitGenParamStackUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the stack unit to which this conceptual row corresponds. Note that the index will be the same index as the index of a 'chassis' physical entity in the entity MIB of the product." ::= { rlPhdUnitGenParamEntry 1 } rlPhdUnitGenParamSoftwareVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the product." ::= { rlPhdUnitGenParamEntry 2 } rlPhdUnitGenParamFirmwareVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the product." ::= { rlPhdUnitGenParamEntry 3 } rlPhdUnitGenParamHardwareVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the product." ::= { rlPhdUnitGenParamEntry 4 } rlPhdUnitGenParamSerialNum OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Serial number of the product." ::= { rlPhdUnitGenParamEntry 5 } rlPhdUnitGenParamAssetTag OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Serial number of the product." ::= { rlPhdUnitGenParamEntry 6 } rlPhdUnitGenParamServiceTag OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Asset tag of the product." ::= { rlPhdUnitGenParamEntry 7 } rlPhdUnitEnvParamTable OBJECT-TYPE SYNTAX SEQUENCE OF RlPhdUnitEnvParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For each module (board) there is an entry describing it in this module" ::= { rlPhysicalDescription 15 } rlPhdUnitEnvParamEntry OBJECT-TYPE SYNTAX RlPhdUnitEnvParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry of this table specifies a module (board)" INDEX { rlPhdUnitEnvParamStackUnit} ::= { rlPhdUnitEnvParamTable 1 } RlPhdUnitEnvParamEntry ::= SEQUENCE { rlPhdUnitEnvParamStackUnit INTEGER, rlPhdUnitEnvParamMainPSStatus RlEnvMonState, rlPhdUnitEnvParamRedundantPSStatus RlEnvMonState, rlPhdUnitEnvParamFan1Status RlEnvMonState, rlPhdUnitEnvParamFan2Status RlEnvMonState, rlPhdUnitEnvParamFan3Status RlEnvMonState, rlPhdUnitEnvParamFan4Status RlEnvMonState, rlPhdUnitEnvParamFan5Status RlEnvMonState, rlPhdUnitEnvParamTempSensorValue EntitySensorValue, rlPhdUnitEnvParamTempSensorStatus EntitySensorStatus } rlPhdUnitEnvParamStackUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the stack unit to which this conceptual row corresponds. Note that the index will be the same index as the index of a 'chassis' physical entity in the entity MIB of the product." ::= { rlPhdUnitEnvParamEntry 1 } rlPhdUnitEnvParamMainPSStatus OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the main PS being instrumented." ::= { rlPhdUnitEnvParamEntry 2 } rlPhdUnitEnvParamRedundantPSStatus OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the redundant PS being instrumented." ::= { rlPhdUnitEnvParamEntry 3 } rlPhdUnitEnvParamFan1Status OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the FAN 1 being instrumented." ::= { rlPhdUnitEnvParamEntry 4 } rlPhdUnitEnvParamFan2Status OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the FAN 2 being instrumented." ::= { rlPhdUnitEnvParamEntry 5 } rlPhdUnitEnvParamFan3Status OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the FAN 3 being instrumented." ::= { rlPhdUnitEnvParamEntry 6 } rlPhdUnitEnvParamFan4Status OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the FAN 4 being instrumented." ::= { rlPhdUnitEnvParamEntry 7 } rlPhdUnitEnvParamFan5Status OBJECT-TYPE SYNTAX RlEnvMonState MAX-ACCESS read-only STATUS current DESCRIPTION "The mandatory state of the FAN 5 being instrumented." ::= { rlPhdUnitEnvParamEntry 8 } rlPhdUnitEnvParamTempSensorValue OBJECT-TYPE SYNTAX EntitySensorValue MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for the Sensor being instrumented." ::= { rlPhdUnitEnvParamEntry 9 } rlPhdUnitEnvParamTempSensorStatus OBJECT-TYPE SYNTAX EntitySensorStatus MAX-ACCESS read-only STATUS current DESCRIPTION "Status value for the Sensor being instrumented." ::= { rlPhdUnitEnvParamEntry 10 } rlPhdStackOrderTopUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This scalar mib holds the Top unit for the stack order command" ::= { rlPhysicalDescription 16 } rlPhdStackOrderBottomUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This scalar mib holds the Bottom unit for the stack order command" ::= { rlPhysicalDescription 17 } rlPhdStackOrderPermutation OBJECT-TYPE SYNTAX OCTET STRING(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This scalar mib holds stack permutation" ::= { rlPhysicalDescription 18 } -- Stack MIB Trap Definitions rlStackUnitRemoved TRAP-TYPE ENTERPRISE rnd VARIABLES { rndErrorDesc, rndErrorSeverity } DESCRIPTION "Trap indicating that a unit was removed from the stack." ::= 186 rlStackConfigChangedRingChain TRAP-TYPE ENTERPRISE rnd VARIABLES { rndErrorDesc, rndErrorSeverity } DESCRIPTION "Trap indicating that the configuration of the stack has changed. - from ring to chain - from chain to ring." ::= 187 rlStackBackupUnitRemoved TRAP-TYPE ENTERPRISE rnd VARIABLES { rndErrorDesc, rndErrorSeverity } DESCRIPTION "Trap indicating that the backup unit was removed from the stack." ::= 188 rlStackMasterSwitchover TRAP-TYPE ENTERPRISE rnd VARIABLES { rndErrorDesc, rndErrorSeverity } DESCRIPTION "Trap indicating that a new master was elected. The old maste is the backup now. " ::= 189 rlStackUnitDifferentSwVersion TRAP-TYPE ENTERPRISE rnd VARIABLES { rndErrorDesc, rndErrorSeverity } DESCRIPTION "Trap indicating that the new unit added to the stack has different software version than the master." ::= 190 rlStackDuplicateUnitNotJoin TRAP-TYPE ENTERPRISE rnd VARIABLES { rndErrorDesc, rndErrorSeverity } DESCRIPTION "Trap indicating that a new unit with duplicated unit id was added to the stack - but it will not join the stack." ::= 191 END