Most Laser printers are equipped with a HP Laserjet Pro M203dw Toner Cartridge. Make sure that you buy a quality toner ink before refilling the toner cartridge. Also, ensure that you collect a star-cut screwdriver, soft cloth, a newspaper sheet or any waste-sheet, any sharp edged driver and a quality HP Laserjet Pro M203dw toner ink bottle.
- The primary step after pulling the toner from a laser printer is to open the screw of the side cover.
- Make sure that you take the side cover off and then remove the drum unit. Carefully hold it from a white portion and pull it in the direction instructed.
- Remove PCR roller, then carefully push PCR rod to right-side with some sharp-edged tool and then slightly move PCR upward and take it out leftwards.
- Make sure you separate the waste unit and ink unit, which are joined together with the help of pins on both sides of the cartridge.
- After pushing pin from the inside, get it out from the outer side and then carefully remove the spring located on the left-side of the HP Laserjet Pro M203dw cartridge.
- Set-apart waste unit and the ink-unit, then remove spring on the right-side and then remove the plastic cover.
- In order to get apart the wiper-blade, you need to remove the screws of the waste unit. Take out the waste-Ink which was collected in the unit.
- Open Wiper-Blade, then wipe the waste collector unit and Blade part. Now, carefully clean the Wiper-Blade with a soft cloth and not with a brush.
- Make sure that you re-assemble the waste-unit part. For that, fit the wiper-blade and then the plastic cover.
- Now, re-fit plastic cover so that it fixes into the cut/groove and then you can fit the spring back to its position.
- Open it and fill the Ink (dry) in it and then close it. Now, finally re-assemble the two units which were separated earlier.
- After removing the side cover, you will observe a white plastic cover. Ascertain that you remove this and fill the toner-ink.
- Now, carefully shake the Ink Bottle before use and after removing the cap of the bottle, close the cap.
- Ascertain that you properly align the Waste unit and ink unit and also reinsert PINS that you removed from both sides.
- Insert PCR roller and then you can install Drum-Unit back to its position after reinserting the pins.
- Once you reinstall drum, make sure that you fit the side-cover and then finally re-insert the Spring.
- It is recommended to have a replacement cartridge available to install when the print quality is no longer acceptable.
- You need to scroll to the bottom of the page and make sure that the country/region is correct.
- Generally, the printer uses four colors: yellow (Y), magenta (M), cyan (C), and black (K) and has a different HP Laserjet Pro M203dw Toner Cartridge for each color.
- They are located inside the front door. Ascertain that you do not remove the toner cartridge from its package until it is time to install it.
- Ascertain that you do not expose it to light for more than a few minutes to prevent damage to the toner cartridge.
- Now,take out and replace the toner cartridges and then press the button on the left panel to open the front door.
- Carefully hold the blue handle on the toner cartridge drawer and then you need to pull out the drawer.
- Now, grasp the handle on the toner cartridge and then you need to pull the toner cartridge straight up to remove it.
- Take out the new toner cartridge from the box and then carefully pull the release tab on the package.
- Remove the toner cartridge from the opened package and then carefully rock the toner cartridge from front to back to evenly distribute it.
- Ascertain that you do not touch the imaging drum on the bottom of the cartridge. Sometimes fingerprints on this may cause print quality problems.
- Ensure that you do not expose the cartridge to light unnecessarily. Now, shut the front door.
- Carefully pack the used HP Laserjet Pro M203dw Toner Cartridge in the package that the new cartridge came in.
- Adhere the pre-paid shipping label to the box so that you can return the used cartridge to HP for recycling.