# Known issues
Notes
- resolved issues are summarized in [resolved issues](README_resolved_issues.md).
- the case id indicates the release when the issue was first recognized.

### V0.50-2 {[issue #28](https://github.com/wfjm/w11/issues/28)} -- RK11: write protect action too slow

Some simple RK11 drivers, especially in test codes, don't poll for completion
of a write protect command. Due to the emulated I/O this can cause errors.

One example is the boot sequence of RK based XXDP, as seen for example for
the `dzzza` disk. On SimH the disk is immediately switched to write protect
mode, on w11 it is not. The pertinent part of the code is
```
    000214  B003:  mov	#000017,@#rk.cs   ; #rk.fwl+rk.go;  func=write_lock
    000222         bic	#017777,r2      
    000226         clc	
    000230         rol	r2
    000232         rol	r2
    000234         rol	r2
    000236         rol	r2
    000240         mov	r2,D040
    000244         mov	#000001,@#rk.cs   ; #rk.go;         func=control reset
```
The monitor does two writes to the RK11 CSR without busy polling and just a
few instructions in between. In the w11 implementation the first write will
set func=write_lock and cause an attn request. But before the attn can be
serviced the CSR is overwritten with func=creset. The write lock is lost,
only the creset is executed.

Can be resolved by handling write lock locally. Normal OS always do
a busy poll before starting a function, therefore this is considered
a minor deficit. Might be fixed in an upcoming release.

### V0.50-8 {[issue #21](https://github.com/wfjm/w11/issues/21)} -- RK11,RL11: no proper NXM check in 18bit systems

No `NXM` error is generated when a UNIBUS device DMA transfer reaches the top
of memory in 18 bit addressing. Seen originally for RK11, but RL11 and DEUNA
are also affected.

In normal operation is minor non-conformity is not relevant because operating
systems never set up DMA transfers to/from non-existing memory. However, some
highly space optimized crash dump routines use this to detect end-of-memory
and might endless loop. Also maindec's might test this border case and fail.

### V0.76-3 {[issue #18](https://github.com/wfjm/w11/issues/18)} -- w11 clock rate limited by CACHE-to-CACHE false path
So far all Series-7 w11a systems ran with 80 MHz clock. The sys_w11_arty
design (with DDR memory support via MIG) also achieves timing closure under
Vivado 2017.2, but fails (with a small negative slack) under Vivado 2018.3.

The failing data path has
```
  Source:      SYS70/CACHE/CMEM_DAT1/sv_ram_reg_0/DOADO[1]
  Destination: SYS70/CACHE/CMEM_DAT3/sv_ram_reg_0/DIADI[1]
  via            VMBOX->SEQ->OUNIT->SEQ->DPATH->SEQ->VMBOX
```
The connectivity of the multiplexers in `pdp_dpath` in principle allows such
a data flow, but `pdp11_sequencer` will never configure the multiplexers in
such a way. So technically this is a false path.

It seems that the placer strategy changed from Vivado 2017.2 to 2018.3 and
that 2018.3 is less tolerant to the sub-optimal w11a design.

This will be fixed in a future release, either by setting up an appropriate
false_path constraint, or by changing the data path structure.

### V0.73-2 {[issue #10](https://github.com/wfjm/w11/issues/10)} -- Many post-synthesis simulations fail
Many post-synthesis functional and especially post-routing timing 
simulations currently fail due to startup and initialization problems. 
Cause is MMCM/PLL startup, which is not properly reflected in the test 
bench. Will be resolved in an upcoming release.

### V0.65-2 {[issue #7](https://github.com/wfjm/w11/issues/7)} -- Some exotic RH70/RP/RM features not implemented
some exotic RH70/RP/RM features and conditions not implemented yet
- last block transfered flag (in DS)
- `CS2.BAI` currently ignored and not handled
- read or write 'with header' gives currently `ILF`

All this isn't used by any OS, so in practice not relevant.

### V0.65-1 {[issue #6](https://github.com/wfjm/w11/issues/6)} -- ti_rri crashes in normal rundown in very rare cases
`ti_rri` sometimes crashes in normal rundown (exit or ^D) when
a `cuff:` type rlink is active. One gets
```
      terminate called after throwing an instance of 'Retro::Rexception'
        what():  RlinkPortCuff::Cleanup(): driver thread failed to stop
```
Doesn't affect normal operation, will be fixed in upcoming release.

### V0.64-6 {[issue #5](https://github.com/wfjm/w11/issues/5)} -- IO delays still unconstraint in Vivado
IO delays still unconstraint in Vivado. All critical IOs use
explicitly IOB flops, thus timing well defined.

### V0.64-2 {[issue #4](https://github.com/wfjm/w11/issues/4)} -- rlink throughput on basys3/nexys4 limited by serial port stack round trip times
rlink throughput on basys3/nexys4 limited by serial port stack 
round trip times. Will be overcome by libusb based custom driver.

### V0.62-2 {[issue #2](https://github.com/wfjm/w11/issues/2)} -- rlink v4 error recovery not yet implemented, will crash on error
rlink v4 error recovery not yet implemented, will crash on error.

### V0.62-1 {[issue #1](https://github.com/wfjm/w11/issues/1)} -- rlink command lists aren't split to fit in retransmit buffer size
rlink command lists aren't split to fit in retransmit buffer size.

_{the last two issues are not relevant for w11 backend over USB usage because
the backend produces proper command lists and the USB channel is usually error
free}_